ページ1に含まれる内容の要旨
3-860-804-23 (1)
Video Cassette
Player
Operating Instructions
PAL NTSC 4.43
SLV-XA17ME/SG
SLV-XA37ME/SG
©1997 by Sony Corporation
ページ2に含まれる内容の要旨
Caution WARNING Television programmes, films, video tapes, and To prevent fire or shock hazard, do not expose other materials may be copyrighted. the unit to rain or moisture. Unauthorized recording of such material may To avoid electrical shock, do not open the be contrary to the provisions of the copyright cabinet. Refer servicing to qualified personnel laws. Also, use of this recorder with cable only. television transmission may require authorization from the cable television The mains lead
ページ3に含まれる内容の要旨
Getting Started Table of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the remote commander 6 Step 3: Connecting the unit 8 Step 4: Tuning your TV to the unit Basic Operations 10 Playing a tape Additional Operations 13 Playing/searching at various speeds 15 Adjusting the picture 16 Editing with another VCR Additional Information 18 Troubleshooting 20 Specifications 21 Index to parts and controls 24 Index Introduction 3
ページ4に含まれる内容の要旨
Getting Started Step 1 Unpacking Check that you have received the following items with the unit: • Remote commander • Aerial cable • Plug adaptor • R6 (Size AA) batteries (SLV-XA17ME/XA37ME only) Checking your model name The instructions in this manual are for the 4 models: SLV-XA17ME, XA17SG, XA37ME, and XA37SG. Check your model number by looking at the rear panel of your unit. The SLV-XA37ME is the model used for illustration purposes. Any difference in operation is clearly indicated in t
ページ5に含まれる内容の要旨
Getting Started Step 2 Setting up the remote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Using the remote commander Remote sensor You can use this remote commander to operate the unit and a Sony TV. To operate this REC unit, point at the remote sensor on the unit. To operate the TV, point at the remote sensor on the TV. TV/VIDEO ; (TV power) u (on/standby) PROG(CH) +/– VOL +/– To Pre
ページ6に含まれる内容の要旨
Step 3 Connecting the unit AERIAL OUT Aerial cable (supplied) AERIAL IN to mains : Signal flow 1 Disconnect the aerial cable from your TV AERIAL OUT and connect it to AERIAL IN on the rear panel of the unit. IN AERIAL 2 Connect AERIAL OUT of the unit and OUT the aerial input of your TV using the IN supplied aerial cable. 3 Connect the mains lead to the mains. Use the supplied plug adapter, if necessary, depending on the design of the mains (SLV-XA17ME/XA37ME only). 6 Getting Started
ページ7に含まれる内容の要旨
Getting Started Additional connections To a TV that has phono type For SLV-XA17ME/SG audio/video input jacks This unit This additional connection TV improves picture and sound quality. AUDIO VIDEO LINE OUT Connect the TV as shown on the IN VIDEO right. AUDIO If you want to use the Trinitron TV Synchro Play function (see page 12), Audio/video cable (not supplied) this connection is necessary. (If your TV has two or more inputs, For SLV-XA37ME/SG connect the audio/video cable to This unit the VID
ページ8に含まれる内容の要旨
Step 4 Tuning your TV to the unit If you have connected your unit to the TV using the audio/video cable, skip this step. ON/STANDBY REC ON/STANDBY 1 Press ON/STANDBY to turn on the unit. 2 Turn on your TV and select a programme position for video playback. Choose a channel between UHF 30 and 39 on the TV where there is no picture and no sound or only a steady rustling sound. This channel will now be referred to as the video channel. 3 Insert a tape recorded in the colour system matching your TV
ページ9に含まれる内容の要旨
Getting Started To obtain a clear playback picture If the playback picture does not appear clearly in step 5 above, turn the RF CHANNEL screw on the rear panel of the unit with a RF CHANNEL screwdriver to a position where the TV clearly displays the playback picture. To select the TV system For your TV to receive the correct signal from your unit, you must set the TV SYSTEM switch on the rear panel of the unit to either G (for system B/G) or K (for system D/K). If this switch is set to the TV S
ページ10に含まれる内容の要旨
Basic Operations Playing a tape 6 EJECT 3/# SEARCH P PAUSE ) FF á PLAY p STOP REC 0 REW NTSC PB COLOR SYSTEM 1 Turn on your TV and set it to the video channel. 2 Insert a tape. (SLV-XA17ME/SG) REC The unit turns on, and starts playing automatically. (SLV-XA37ME/SG) The unit turns on, and starts playing automatically if you insert a tape with its safety tab removed. 3 PLAY Press á PLAY. When the tape reaches the end, it will rewind automatically. Basic Operations 10
ページ11に含まれる内容の要旨
Basic Operations Additional tasks To Press Stop play p STOP Pause play P PAUSE Resume play after pause P PAUSE or á PLAY Search forward ) FF or # SEARCH during playback Search backward 0 REW or 3 SEARCH during playback Fast-forward the tape ) FF during stop Rewind the tape 0 REW during stop Eject the tape 6 EJECT To set the colour system If streaks appear during playback, set COLOR SYSTEM on the unit to conform to the system that the tape was recorded in. (Normally set the switch to AUTO.) If y
ページ12に含まれる内容の要旨
Playing a tape (continued) Tip • You can play back tapes recorded in the SP, LP, and EP mode. Notes • Depending on your TV, the following may occur while playing an NTSC-recorded tape: – the picture is black and white, – the picture shakes, – no picture appears on the TV screen, – black streaks appear horizontally on the TV screen, and – the colour density increases or decreases. • You can eject a tape even when the power is off. When you press 6 EJECT, the unit turns on automatically. After e
ページ13に含まれる内容の要旨
Additional Operations Playing/searching at various speeds SLOW +/– 3/# SEARCH á PLAY 03 REW )# FF 7 FRAME ) FF á PLAY 0 REW REC Playback options Operation Fast-forward/rewind During stop, press ) FF or 0 REW. View the picture during fast- During fast-forward, hold ) FF down. During rewind, hold forward or rewind 0 REW down. Play at high speed During playback or pause, press # SEARCH or 3 SEARCH. Play in slow motion During playback or pause, press SLOW +/–. Press the +/– buttons to change the s
ページ14に含まれる内容の要旨
Playing/searching at various speeds (continued) To resume normal playback Press á PLAY. Tip • If the picture shakes while in the still mode, adjust the picture using $/4 TRACKING NORMAL/SLOW STILL ADJUST. Notes • Streaks or snow cannot be eliminated completely in the various playback operations, especially in the slow motion mode. • The sound is muted during these operations. • If you press 7 FRAME during playback, playback continues at the normal speed but the sound is muted. Press á PLAY to r
ページ15に含まれる内容の要旨
Adjusting the picture Adjusting the tracking TRACKING Although the unit automatically AUTO/ adjusts the tracking when MANU playing a tape, distortion may occur if the tape was recorded in poor condition. If so, manually $/4 adjust the tracking. TRACKING Press $/4 TRACKING NORMAL/ NORMAL/SLOW to obtain the SLOW best possible picture. The distortion should disappear as you press one of the two buttons. If you cannot get a clear picture with manual adjustment, press TRACKING AUTO/MANU to return t
ページ16に含まれる内容の要旨
Editing with another VCR How to connect to record on this unit (SLV-XA37ME/ SG only) This unit (Recorder) TV LINE IN Other VCR (Player) LINE OUT Audio/video cable (not supplied) : Signal flow Tip • Use a commercially available 2-phono to 2-phono type audio/video cable. If the other VCR has the AUDIO L and R jacks, use a commercially available 3-phono to 2-phono type audio/video cable. Notes • Make sure you connect the plugs to the jacks of the same colour. • When connecting the units, do not si
ページ17に含まれる内容の要旨
P PAUSE Operation (when recording on this unit) (SLV-XA37ME/SG only) You can make a copy of a tape REC using this unit for recording or playback. The unit cannot record TV programmes directly since it TAPE SPEED r REC does not have a TV tuner. Before you start editing • Turn on your TV and set it to the video channel. 1 Set TAPE SPEED to select the tape speed (SP or LP for the PAL colour system, and SP or EP for the NTSC colour system). LP provides a recording time twice as long as SP. EP prov
ページ18に含まれる内容の要旨
Additional Information Troubleshooting If you have any questions or problems not covered below, please consult your nearest Sony service facility. Symptom Remedy The ON/STANDBY switch • Connect the mains lead securely. does not function. The power is turned on but the • Moisture condensation occurs. Turn the power off, unit does not operate. unplug the mains lead and leave the unit to dry for over an hour. • The auto safety system is triggered to protect your tape The unit enters standby mode a
ページ19に含まれる内容の要旨
Symptom Remedy No tape can be inserted. • Check that a tape isn’t already in the tape compartment. The remote commander does • Make sure you are pointing the remote commander at not function. the remote sensor on the unit. • Replace all the batteries in the remote commander with new ones if they are weak. The unit needs to be cleaned. • Clean the cabinet, panel, and controls with a dry soft cloth, or a soft cloth slightly moistened with a mild detergent solution. Do not use any type of solvent,
ページ20に含まれる内容の要旨
Specifications System Supplied accessories RF output signal Remote commander (1) UHF channels 30 to 39 R6 (Size AA) batteries (2) Aerial out Aerial cable (1) 75-ohm asymmetrical aerial socket Plug adaptor (SLV-XA37ME/ SLV-XA17ME only) (1) Inputs and outputs LINE IN (SLV-XA37ME/SG only) Design and specifications are subject to change VIDEO IN, phono jack (1) without notice. Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO IN, phono jack (1) Input level: 327 mVrms Input impedance: mo
