ページ1に含まれる内容の要旨
TEC Electronic Cash Register
FS-1450-1 SERIES
Owner’s Manual
ページ2に含まれる内容の要旨
NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operati
ページ3に含まれる内容の要旨
EO1-11099 Safety Summary Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual, turn off th
ページ4に含まれる内容の要旨
EO1-11099 Safety Summary Disconnect Disconnect If foreign objects (metal fragments, When unplugging the power the plug. the plug. water, liquids) enter the machines, cords, be sure to hold and pull on first turn off the power switches and the plug portion. Pulling on the cord disconnect the power cord plugs from portion may cut or expose the inter- the outlet, and then contact your nal wires and cause fire or electric authorized TOSHIBA TEC repre- shock. sentative for assistance. Continue
ページ5に含まれる内容の要旨
OPERATOR’S GUIDE – 1 –
ページ6に含まれる内容の要旨
EO1-11097 TABLE OF CONTENTS Page 1. TO OUR CUSTOMERS ................................................................................................................... 1 2. UNPACKING .................................................................................................................................... 2 3. APPEARANCE AND NOMENCLATURE......................................................................................... 3 4. MODE LOCK AND MODE SELECTOR KEYS .......................
ページ7に含まれる内容の要旨
EO1-11097 1. TO OUR CUSTOMERS Thank you for choosing the TEC electronic cash register FS-1450 series. This instruction manual provides a description of the functions and handling of this register and should be read carefully to ensure optimum performance. Since every consideration has been given to safety and reliability, there is no danger of damaging the machine by incorrect operation. Please refer to this manual whenever you have any questions concerning the machine. This machine has been ma
ページ8に含まれる内容の要旨
EO1-11097 2. UNPACKING 1 2 3 7 4 56 8 1 Paper Roll 45 mm x Ø50 mm (2 pcs.) 5 Ribbon Cassette (1 pc.) 2 Mode Key 6 Journal Reel (1 pc.) (REG Key, MGR Key, MA Key, 7 Drawer Key (2 pcs.) S Key; 2 pcs. respectively) 8 Owner's Manual (1 pc.) 3 Receipt Cover Key (2 pcs.) 4 Stamp lnk (1 pc.) - 2 -
ページ9に含まれる内容の要旨
EO1-11097 3. APPEARANCE AND NOMENCLATURE Journal Window Customer Display Receipt Outlet Operator Display Mode Lock Power Switch Drawer Keyboard • Power Switch........ The power switch is provided at the right-hand side of the cabinet. The AC power is turned on when the switch is pushed to ON, and turned off when the switch is pushed to OFF. - 3 -
ページ10に含まれる内容の要旨
EO1-11097 4. MODE LOCK AND MODE SELECTOR KEYS 4.1. MODE LOCK (POSITION) (FUNCTION) SET ........... In this position, the register will allow pro- gramming operations MGR X .................. (LOCK position) The register operations are REG locked when the Mode Lock is in this posi- REG REG (SPERRE) tion. Meanwhile, the Display Message and Z Schlüssel Key the current time are displayed. SET REG .......... Normal cash register operations are carried out in this mode. However, the operations requ
ページ11に含まれる内容の要旨
EO1-11097 5. DISPLAY The operator display is located at the top of the register just above the keyboard. OPERATOR DISPLAY (Front Display) SLIIP AMOUNT RPT DP IN-LINE SIGN ON TL ALM ST R OFF CG The customer display can be fixed as a rear display or moved to form a remote display. It can be moved up, down, to the right, and to the left, and thus is fully adjustable according to the position of the customer. CUSTOMER DISPLAY (Rear or Remote Display) AMOUNT TL ST CG - 5 -
ページ12に含まれる内容の要旨
EO1-11097 5.1. NUMERIC DISPLAY AMOUNT (7 digits): Displays the numeric data, such as amount, quantity, etc. When the amount is negative, the symbol "-" is displayed as well. NOTE: When the following code is being entered, the digits for "RPT" and "DPT" may be used as well (all 10 digits). On exceeding the 10 digits, the lowest 10 digits are being displayed. Non-add Number (max. 18 digits) DPT (2 digits): Displays the Department Code of the department item just entered. It stays lit when repea
ページ13に含まれる内容の要旨
EO1-11097 6. OUTLINE OF PREPARATION PROCEDURE BE- FORE OPERATING THE ECR This chapter shows the outline of set-up procedure of the ECR before actually starting the ECR operation. WARNING! Turn the POWER SWITCH to OFF before connecting the power cord. (1) (2) (3) (7) (4) (5) (6) (8) 1 Remove the cash register from the carton, referring to Chapter "2. Unpacking". And take out all the parts and accessories. 2 Remove the tapes and seals for holding parts or protecting the register surfaces. 3 Plug
ページ14に含まれる内容の要旨
EO1-11097 6 Install the Receipt and Journal rolls (referring to the following section "Installing the Receipt/Journal Roll"). Installing the Receipt/Journal Roll WARNING! Care must be taken not to injure yourself with the paper cutter. Installing the Receipt Roll MGR X 1 REG - Turn the Mode Lock to the REG position with power Z ON. SET 2 To remove the Receipt Cover, insert the Receipt Cover Key to the Receipt Cover Lock, and then turn it 90˚ clockwise. 3 Cut the paper end to make it sharp. 4 Hol
ページ15に含まれる内容の要旨
EO1-11097 5 Place the paper roll in the outer side holder of the two roll holders. There are the following two ways of receipt paper feed procedure. 6 A: Manual installation B: Installation using the [RF] key A: Manual installation 1 Lift the green lever on the receipt side. 2 Insert paper from the rear of the printer until the leading edge of paper comes out by 10 cm. 3 Lower the green lever. 4 Attach the receipt cover. B: Installation using the [RF] key 1 Insert paper from the rear of the pr
ページ16に含まれる内容の要旨
EO1-11097 Installing the Journal Roll Follow Steps 1 to 5 for "Installing the Receipt Roll" on the preceding pages, except that 1 the paper roll should be placed inner side holder of the two holders. There are the following two ways of a journal paper feed procedure. 2 A: Manual installation B: Installation using the [JF] key A: Manual installation 1 Lift the green lever on the journal side. 2 Insert paper from the rear of the printer until the leading edge of paper comes out by 30 cm. 3 Insert
ページ17に含まれる内容の要旨
EO1-11097 Setting the Ribbon Cassette Detach the Ribbon Cover. 1 Set the Ribbon Cassette. 3 After setting the Ribbon Cassette, turn the knob of the Ribbon Cassette in the arrow direction several times to remove the slack on the ribbon. Attach the Ribbon Cover. 4 - 11 -
ページ18に含まれる内容の要旨
EO1-11097 7. CASHIER SIGNING OR CASHIER KEY OPERATIONS The FS-1450 adopts one of the following cashier-identifying operations. • CODE ENTRY METHOD, using the [LOG/RECEIPT] (or [LOG]) key. • CASHIER KEY METHOD, (hardware option), using Cashier Keys. • CASHIER KEY METHOD, using [CLK] keys. 7.1. CODE ENTRY METHOD Each cashier will sign-ON, sign-OFF, sign-IN, and sign-OUT through the [LOG/RECEIPT] (or [LOG]) key. OPERATION: Mode Lock: REG (or, MGR or with Manager Intervention) ([LOG/RECEIPT] = [LO
ページ19に含まれる内容の要旨
EO1-11097 NOTES: 1. Sign-OUT may automatically be performed without operating "9 [LOG]" on finalizing each transaction including Check (or other non-cash media) Cashing, No-sale Exchange from/ to Foreign Currencies, No-sale, Received-on-Account, Paid-Out, Loan, and Pick Up if so set by a program option. When this option is selected, Sign-IN is always necessary before starting every transaction. 2. When the finalizing media key is programmed with Validation Compulsory or Endorsement Compulsory
ページ20に含まれる内容の要旨
EO1-11097 (3) Mode Changes With Signing Operations When Signed-ON or Signed-IN: The Mode Lock position changes are allowed within "LOCK", "REG", "MGR", and " ". Changing to any other position will be an error. When Signed-OUT: The Mode Lock may be turned to any position. However, cashier reports of the cashier being signed OUT cannot be taken in the "X" or "Z" position. When Signed-OFF: The Mode Lock may be turned to any position. Therefore, it is best for the cashier (or all the cashiers on a
