ページ1に含まれる内容の要旨
Jiva TP/LT- 5600/5800 Series
Touch Terminal
User’s Manual
Rev. A0
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when oper
ページ2に含まれる内容の要旨
ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery and maybe also a sealed type Lead acid battery if the UPS battery option is ordered. Please always follow local environmental protection laws / regulations for disposal of used batteries and
ページ3に含まれる内容の要旨
BRIEF INTRODUCTION The User’s Manual The purpose of this manual is to guide the user in the initial installation and general use of the Posiflex Jiva TP/LT-5600 series and Jiva TP/LT-5800 series of POS terminals. It does not explain any application software that may be supplied with it. We intend to provide our customers with all technology advantages available by evolving the product design to incorporate appropriate changes and improvements. So some detail differences may exist betwe
ページ4に含まれる内容の要旨
Long life touch panel that endures 10 million touches at same spot (for Jiva TP only) Spill proof water resistant structure allowing easy cleaning Easy maintenance construction Various I/O ports supported, including: 1. one PS/2 KB port 2. one PS/2 mouse port 3. 4 serial ports with capability for +5V DC support (reduce to 3 ports if RS232 interface touch panel is used) 4. one parallel port 5. 2 USB ports 6. one LAN port 10/100 base T Ethernet 7. one external VGA monitor port 8. on
ページ5に含まれる内容の要旨
MSR or smart card reader and finger print sensor or iButton reader ² Security upgrade kit SD200 covering options of USB interface MSR or optical scan type finger reader ² Bar code card reader BC-100U d) Integrated rear top mount LCD customer display PD-302 e) 2 in 1 cash drawer control cable (CCBLA-238) f) USB interface external slim type CD ROM drive g) UPS battery h) Preload OS i) Wall mount kit j) IDE cable kit (for Jiva TP/LT-5800 only) Part 5
ページ6に含まれる内容の要旨
INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded. Failure to do the above will void the product warranty! OPENING CABLE COVER Please first push the lock/release
ページ7に含まれる内容の要旨
DISCONNECTING CABLES After removal of the cable cover, the connector area will be accessible then. Please disconnect every cable before separation of main unit and the adjustable stand assembly. When later the main unit and stand assembly are to be re-assembled for application, please connect all required cables to the appropriate connectors. Please make sure that each connector is connected to the right port with the correct orientation. Damages due to incorrect connection or orientati
ページ8に含まれる内容の要旨
and take the cable passage cover away to show the cable passage. If there is no need to install the optional UPS battery here, please skip Screws the next paragraph and start routing cables through the cable passage. Cable Otherwise, please remove the four Passage screws holding the battery cover to Cover install the battery. INSTALLING UPS BATTERY Place the optional UPS battery in the battery compartment (shown below left). Screw on the battery cover and route the battery cab
ページ9に含まれる内容の要旨
ROUTING THE CABLES Fix this End of the Cover First Route Cables under the Cover Connect this End to Main Unit This End to Other Devices Place all the cables required for connections to the Jiva TP/LT-5600 or Jiva TP/LT-5800 except those for special application purposes into the cable passage. Insert one end of the cable passage cover under the adjacent cover plate and screw on the two screws. Be sure not to damage any of the cables during this operation. Now, turn the a
ページ10に含まれる内容の要旨
INSTALLING UPGRADE KIT Please follow the instructions in the manuals delivered with the side mount upgrade kit: KP100, SD100, SD200 or BC100U and the rear top mount upgrade kit PD302 to fit them in Jiva 5600 / Jiva 5800 construction. The USB power arrangement in this system has been particularly designed to help smooth start up of the fingerprint sensor in SD200. WIRELESS PRINTER The whole Jiva series can access the Posiflex wireless thermal printer PP7700 in Windows environment except
ページ11に含まれる内容の要旨
JOINING MAIN UNIT AND STAND Matching Pegs Matching Holes Round Part Slot Part Removal Hollow Match the matching pegs on the back of the main unit against the matching holes on the stand. First aim the matching pegs toward the upper round part of the hole and make sure that all pegs are inside the holes. Then slide the main unit down to move the pegs into the lower slot part of the holes till it clicks. Note that all the cables come out of the stand from the lower edge
ページ12に含まれる内容の要旨
assembly. The stand assembly is not engaged in wall mount operation. Wall Mount Bracket Matching Holes Show Screw this Holes side out. LOCATION FOR INSTALLATION As the stand assembly is not involved in wall mount installation, the space required for wall mount application will take only the main unit into consideration. So the space required is 375 mm in width and 315 mm in height. For desk top/counter application, the adjustable stand assembly requires a base of
ページ13に含まれる内容の要旨
For Jiva TP/LT-5800, the operating system exists in the HDD. Once the software system on HDD collapses, it is possible to restore the operating system onto a physically intact HDD with use of the Recovery CD that comes with the preloaded operating system. Please follow the instruction from your system integrator for system / software restoration. Follow the instructions below for operating system recovery only if your system integrator does not advise otherwise. For the Jiva TP/LT-5800
ページ14に含まれる内容の要旨
USING THE TOUCH POS APPLICATION ENVIRONMENT It is very important that you check the following operation guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. The installation should be such that there is at least 25mm air clearance around any top or side ventilation holes. The installation must also be such that there is a free flow of air around the unit at ALL times. Operating Environment The equipment must not be operated or store
ページ15に含まれる内容の要旨
Emergency treatment: The battery is constructed maintenance free and leakproof. It is well protected in Jiva system as long as the ambient temperature remains below 30°C and the ventilation of the Jiva system remains free. However, should any accident happen and the sulfuric acid from the battery spills on skin or clothing, wash immediately with water. If the acid comes in contact with eyes, rinse eyes with large amount of clean water and see a doctor immediately. A larger external batt
ページ16に含まれる内容の要旨
Hardware Power Switch The power switch located at left side of the main unit is a slide type switch. This switch controls the power on/off of the system. This switch turns the system on when slid downward, only when external power is present. The switch will always spring back to its original position when pressure is removed. This switch turns the system off when slid downward again during power on status. However, if the system hangs due to any reason such as software resource conflic
ページ17に含まれる内容の要旨
3. Alarm setup detail will appear. Set the alarm as wished then press “F10” key to save and exit CMOS setup. 4. This system may be powered off and will automatically boot up at the preset alarm time. By RS232 MODEM Ring up 1. Preset the system to boot up on RS232 MODEM ring by pressing “Del” key at powering up this system to enter system BIOS CMOS setup. 2. Select “Power Management Setup” and enter “PM Wake Up Events”. Go to item “Ring Power Up Control” and change the setting to “Ena
ページ18に含まれる内容の要旨
VGA cable or purchase another type of VGA cable and set an internal jumper in Jiva TP/LT-5600 or Jiva TP/LT-5800 to supply the required power through the VGA connector. Do not connect other monitor to this port before the power in this port is disabled. TOP MOUNT CUSTOMER DISPLAY Please follow the instructions on the manual that comes along with the top mount customer display PD302 when it is installed. SERIAL PORTS – COM1/2/3/4 In Jiva TP/LT-5600 / Jiva TP/LT-5800, there are 4 serial
ページ19に含まれる内容の要旨
a matter of few seconds that the system will automatically shutdown power due to uprising temperature. Please review the ventilation condition and environment temperature, check if the fan is stuck by contaminants such as dry grease or threads and try to correct the situation when the system is off and cooled down. You may power up the system again after the system cooled down and trouble cause removed. However, if the warning pops up soon again, please consult your dealer for possi
ページ20に含まれる内容の要旨
RS232 Touch Controller If the Jiva TP-5600 or Jiva TP-5800 purchased is the leading edge Infra Red type touch models, the touch controller is of RS232 interface. The “Posiflex Touch Terminal Manager” above should be disregarded. In these models, the COM4 position of the system will be covered in the connection area. Removal of this cover will void the product warranty!! Once the RS232 touch controller driver is installed, the user can utilize it to control the mouse emulation. Please cl
