ページ1に含まれる内容の要旨
Inductive Loopset LPS-4
User Guide
9354812
Issue 3
ページ2に含まれる内容の要旨
DECLARATION OF CONFORMITY We, NOKIA CORPORATION declare under our sole responsibility that the product LPS-4 is in conformity with the provisions of the following Council Directive: 1999/5/EC. A copy of the Declaration of Conformity can be found from http://www.nokia.com/phones/declaration_of_conformity/. The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of-life. Do not dispose of these products as unsorted m
ページ3に含まれる内容の要旨
The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you. Unauthorized changes or modifications to this device may void the user's authority to operate the equipment. Export Controls This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited. 9354812 / Issue 3
ページ4に含まれる内容の要旨
1. General The Mobile Inductive Loopset LPS-4 for people with hearing aids is developed to facilitate the use of a compatible mobile phone together with T-coil equipped hearing aids. When using the inductive loopset, you can speak directly to the microphone inside it. You do not need to hold a mobile phone near your ear, but you can carry it using a carrying case, belt clip, or other accessory. The loopset does not require any separate batteries. The operation of the device is based on ind
ページ5に含まれる内容の要旨
2. Using the loopset ■ Make and receive calls 1. Place the loop around your neck, and connect the plug to its counterpart. 2. Connect the Pop-Port plug to the bottom of the phone. The phone displays the following symbol: 3. Switch your hearing aid to the T or MT mode. © 2006 Nokia. All rights reserved. 5
ページ6に含まれる内容の要旨
4. To answer or end a call, press the answer button on the device or use the keys on your phone. Calls can be made in the normal way (see the user guide of your phone). Notes The lead does not need to be connected to the Pop-Port connector of the phone all the time. You can choose to connect it only when you wish to make or receive calls. When you receive a call, both the phone and the loopset sound an alert if the lead is connected to the phone and if the hearing aid is in the T or MT
ページ7に含まれる内容の要旨
■ Connect the loopset to external devices The loopset can be connected to a compatible speech processor of a cochlear implant or to the audio input of a hearing aid. Contact your hearing aid specialist for the compatibility with your cochlear implant or hearing aid, the correct connection cable, and instructions on the use of the connection cable. Connect the plug of the external device to the audio output connector with the symbol on the right side of the loopset device. © 2006 Nokia.
ページ8に含まれる内容の要旨
3. Technical data External audio output: Connector: 3.5-mm socket Can be connected to the audio input of a compatible hearing aid or to a compatible speech processor of a cochlear implant Impedance: >1 kΩ @ 1 kHz (nominal 2.2 kΩ @1 kHz) Typical output signal level: 0.5–10 mV rms Symbol: The loopset can be connected to a compatible speech processor with a suitable cable that has a 3.5-mm stereo or mono plug. The sound that you hear through the loopset is monophonic. External audio i
ページ9に含まれる内容の要旨
Care and maintenance Your device is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you protect your warranty coverage. Keep the device out of the reach of small children. Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, allow the device to dry completely. Do not use or store the device in dusty, dirty
