ページ1に含まれる内容の要旨
MOTORIZED 7 IN -DASH
LCD COLOR MONITOR
WITH AM/FM STEREO RADIO
PLR7N
MODEL:
OWNER S MANUAL
ページ2に含まれる内容の要旨
Any changes or modifications in construction of this device which is not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.
ページ3に含まれる内容の要旨
! WARNING The exclamation point within an equilateral triangle and WARNING are intended to alert the user to the presence of important operating instructions. Failure to heed the instruction will result in severe injury or death. DO NOT WATCH VIDEO WHILE DRIVING Watching the video may distract the driver from looking ahead of the vehicle and cause an accident. DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE Any function that requires your prol
ページ4に含まれる内容の要旨
! CAUTION The exclamation point within an equilateral triangle and CAUTION are intended to alert the user to the presence of important operating instructions. Failure to heed the instructions can result in injury or material damage. DO NOT RAISE THE VOLUME EXCESSIVELY Keep the volume at a level, where you can still hear outside noises while driving . Driving while unable to hear outside could cause an accident. DO NOT USE THIS EQUIPMENT OUTSIDE THE VEHICLE Do not use this equipment for pu
ページ5に含まれる内容の要旨
! CAUTION The exclamation point within an equilateral triangle and CAUTION are intended to alert the user to the presence of important operating instructions. Failure to heed the instructions can result in injury or material damage. Operation of some of the functions of this unit is very complex. Because of this, it was deemed necessary to place these functions into a special SETUP screen. This will restrict operation of these functions to times when the vehicle is parked. This ensures th
ページ6に含まれる内容の要旨
INTRODUCTION MONITOR POWER ON/OFF BUTTON MODE SELECTION BUTTON AS/ATM BUTTON SOUND MUTE BUTTON VOLUME UP/DOWN ADJUST BUTTON SEARCH UP/DOWN BUTTON OPEN/CLOSE BUTTON TILT UP/DOWN BUTTON BAND SELECTION BUTTON MENU SELECTION BUTTON 4
ページ7に含まれる内容の要旨
REMOTE CONTROLLER POWER ON/OFF BUTTON MODE SELECTION BUTTON AS/ATM BUTTON SOUND MUTE BUTTON VOLUME UP/DOWN BUTTON SEARCH UP/DOWN BUTTON OPEN/CLOSE BUTTON MANUAL MEMORY BUTTON CHANNEL UP/DOWN BUTTON NAVIGATION BUTTON ASPECT BUTTON MENU SELECTION BUTTON 5
ページ8に含まれる内容の要旨
REMOTE CONTROL UNIT Replacing battery Applicable battery : Use two AAA sized dry batteries. 1. Opening the battery cover. Push and slide the cover in the arrow direction, and the cover will be removed. 2. Replacing the battery. Remove the old batteries. Insert new ones matching the (+) and (-) polarities as shown in the diagram inside the unit. 3. Closing the cover. Push the cover in the arrow direction until a click is heard. 6
ページ9に含まれる内容の要旨
BASIC OPERATION POWER ON / OFF RADIO MAIN MENU 1. POWER ON 1) Press the POWER button to turn the power on. But the monitor will not open. 2) You can also turn the power on by pressing the OPEN/CLOSE button. The power will be on and the monitor will open. 2. POWER OFF 1) Press the POWER button again to turn the power off. 2) If you turn the power off by pressing the POWER button when the monitor opens, the monitor will not close. If the car key is pulled out, or the OPEN/CLOSE button is
ページ10に含まれる内容の要旨
CLOSING THE MONITOR 1. Hold left and right upper side of the monitor and set the left and right angle of the monitor parallel with the front of the unit as the picture. 2. Press OPEN/CLOSE button. The monitor will close. NOTE 1. If the left and right angle of the monitor is not parallel to the front of the unit, the monitor can not be closed. 2. If the OPEN/CLOSE button is pressed while radio or video is on, the monitor will close. But the sound is still on. Press the POWER button to turn t
ページ11に含まれる内容の要旨
ADJUSTING THE SLIDE POSITION 1. Press the MENU button repeatedly on radio or AV mode until the USER SELECTOR menu is selected. 2. Press the SEARCH UP/DOWN button to select MOVE 3. Press the VOLUME button to select FORWARD. The monitor will slide one step (15mm) to the front. 4. Press the VOLUME button to select BACKWARD. The monitor will slide one step (15mm) to the back. For more information, see page 21 of owner s manual. NOTE 1. If the VOLUME button is pressed when FORWARD is selected,
ページ12に含まれる内容の要旨
SELECTING MODE Press the MODE button to select the desired mode. Each time you press the button, the mode changes as follows. RADIO -> AV1 -> AV2 -> AV3 (CD OR VCD CHANGER) -> AV4 (TV) NOTE 1. AV3 has only video input. 2. The CD/VCD changer must be connected to the 8 pin DIN socket on the rear of the unit with 8 pin DIN cable in our CD/VCD changer gift box. 3. The video output of VCD changer must be connected to AV3 video input. If the video output of VCD changer is not connected AV3 video
ページ13に含まれる内容の要旨
ADJUSTING THE TV/VIDEO PICTURE MODE (ASPECT) Each time you press A (ASPECT) button, the picture mode switches between Normal, Full, Zoom and Wide. NORMAL MODE The monitor displays normal picture at the center of the screen with the proportion of 4 to 3. The screen shows a vertical black belt at each side. FULL MODE The monitor displays normal picture wider by stretching out horizontally with the proportion of 16 to 9. ZOOM MODE The monitor displays normal picture wider by stretching out ho
ページ14に含まれる内容の要旨
RADIO CONTROL Press the OPEN/CLOSE button to turn the power on and to open the monitor. The monitor shows following picture. RADIO MAIN MENU NOTE 1. Each time you press the MENU button on RADIO MAIN MENU screen, the menu on the screen changes as follows. RADIO SUB -> VOLUME -> USER SELECTOR -> PICTURE -> RADIO MAIN 2. You can select the items on each menu by pressing the SEARCH UP/DOWN button. 3. You can adjust the level of the selected items by pressing the VOLUME or CH UP
ページ15に含まれる内容の要旨
AUTO MEMORY OF STATION 1. Tune in desired radio station you wish to store on the CH number. 2. Press the AS/ATM button for at least 2 seconds. The frequency on the display continues to change while the auto memory is in progress. The tuner will automatically seek and can store up to 30 stations in each band in order of frequency signal. They can be stored in FM1: 30, FM2: 30, AM1: 30 and AM2: 30 stations (total 120 stations). 3. When the auto memory has been completed, the tuner goes to th
ページ16に含まれる内容の要旨
RADIO BAND 1. Press the SEARCH UP/DOWN button to select RADIO BAND. 2. When RADIO BAND is selected, press the VOLUME button to select the band. Each time you press the VOLUME button, the band switches as follows. FM1 -> FM2 -> AM1 -> AM2 3. You can also select the band by pushing the BAND button on the unit. Each time you press the BAND button, the band switches as follows. FM1 -> FM2 ->AM1 -> AM2 TREBLE 1. Press the SEARCH UP/DOWN button to select TREBLE. 2. Press the VOLUME button
ページ17に含まれる内容の要旨
NAVIGATION SETTING THE NAVIGATION 1. Connect a NAVIGATION system to AV1 or AV2 Input terminals on the rear of the unit. 2. Press the MODE button to select radio mode. 3. Press the MENU button to select following picture. RADIO SUB MENU 4. Press the SEARCH UP/DOWN button to select NAVIGATION. 5. Press the VOLUME button to select AV1 or AV2 that NAVIGATION system is connected to. Each time you press this button, AV Input changes as follows AV 1 -> AV2 -> OFF WATCHING THE NAVIGATION PICTU
ページ18に含まれる内容の要旨
CAMERA IN SETTING THE CAMERA IN 1. Connect a Back View Camera video output to AV1,2 or 3 video Input terminals on the rear of the unit. * When the VCD changer is connected to AV3 Video input, The back view camera can be connected only to AV1 or AV2 video input. 2. Press the MODE button to select radio mode. 3. Press the MENU button to select following picture. RADIO SUB MENU 4. Press the SEARCH UP/DOWN button to select CAMERA IN. 5. Press the VOLUME button to select AV1,2 or 3 mode that Ba
ページ19に含まれる内容の要旨
CD CHANGER CONTROL When a CD (VCD) changer is connected to this unit with 8 pin DIN cable, AV3 mode changes to CDC mode and CDC control menu is displayed on the screen. 1. Press the MODE button to select CD CHANGER (AV3) mode. Each time you press this button, the display changes as follows. RADIO-> AV1-> AV2-> AV3 (CD or VCD CHANGER) -> AV4(TV) 2. When CD CHANGER (AV3) mode is selected, The monitor shows following picture. 3. Press the SEARCH UP/DOWN button to select the item. 4. Press t
ページ20に含まれる内容の要旨
TRACK NUMBER 1. Press the SEARCH UP/DOWN button to select TRACK NUMBER. 2. Each time you press the CH UP button, the next track number will be selected forward and the displayed track number increases by one. 3. Each time you press the CH DOWN button, the previous track number will be selected and the displayed track number decreases by one. INTRO SCAN 1. Press the SEARCH button to select INTRO SCAN. 2. Press the CH UP/DOWN button to select the item. Each time you press the CH UP/DOWN button or
