ページ1に含まれる内容の要旨
®
Installation/Operation
PMCL15A
TFT LCD Monitor
C1965M-C (12/03)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
ページ2に含まれる内容の要旨
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ..................................................................................... 3 REGULATORY NOTICES ........................................................................................................................ 3 DESCRIPTION ........................................................................................................................................ 4 INSTALLATION ..................................................
ページ3に含まれる内容の要旨
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco. 4. After replacem
ページ4に含まれる内容の要旨
SVCR DESCRIPTION The PMCL15A is a high resolution, 15-inch, thin film transistor (TFT) LCD color monitor. The unit produces a sharp picture with a resolution of 540 TV lines. The monitor features multiple video inputs for S-video and PC-based imaging and supports circuitry for NTSC/PAL formats with input voltages of 100-240 VAC. INSTALLATION 1. The monitor can be placed on any flat surface, desk, or table. 2. Refer to Figure 1 and connect the video signal to the monitor. Refer to Table A for vid
ページ5に含まれる内容の要旨
Table A. Video Coaxial Cable Requirements Cable Type* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) * Minimum cable requirements: 75 ohms impedance All-copper center conductor All-copper braided shield with 95% braid coverage Figure 2. Looping Operation - One Monitor with External Video Equipment [ ] Pelco Manual C1965M-C (12/03) 5
ページ6に含まれる内容の要旨
Figure 3. Looping Operation - Maximum of Three Monitors With External Video Equipment [ ] 6 Pelco Manual C1965M-C (12/03)
ページ7に含まれる内容の要旨
Front Panel Controls Refer to Figure 4. 1 CHANNEL BUTTON Channel Select - Press the Channel button once to display a camera view. Auto Scan - Press and hold the button for three seconds to sequence through composite video channels. 2 MENU BUTTON - On-screen display menu (OSD). 3 BUTTONS - Use to navigate through the OSD menus. 4 POWER LED Green - Power ON Dark - Power OFF Yellow - Power-saving mode 5 POWER BUTTON - Press the power button to turn the monitor ON/OFF. 1 2 3 4 5 Channel Menu 00871
ページ8に含まれる内容の要旨
▲ ▲ ▲ OPERATION 1. Turn the monitor’s main power switch ON. The power switch is located on the base of the monitor (refer to Figure 1). 2. Push IN the power button located on the front of the monitor (refer to Figure 4). The LED turns green. 3. Push the Channel button to select the input signal. 4. If required, adjust the video using the front panel controls and the on-screen display (OSD). How To Adjust The Video Use the front control panel to adjust the screen display. 1. Press the Menu button
ページ9に含まれる内容の要旨
▲ ▲ ▲ ▲ ▲ ▲ ▲ Video Mode BRIGHTNESS Press the button to increase brightness and the button to decrease brightness. Default setting is 80%. CONTRAST Proper adjustment will allow maximum gradations between the darkest and lightest picture contrast. Press the button to increase contrast and the button to decrease contrast. Default setting is 70%. RGB COLOR Press the button to increase saturation level and the button to decrease color saturation level. Default setting
ページ10に含まれる内容の要旨
▲ ▲ ▲ ▲ ▲ PC Mode CONTRAST Proper adjustment will allow maximum gradations between the darkest and lightest picture contrast. Press the button to increase contrast and the button to decrease contrast. Default setting is 85% BRIGHTNESS Press the button to increase brightness and the button to decrease brightness. Default setting is 80%. H POSITION Adjust the horizontal position of the image on the screen. V POSITION Adjust the vertical position of the image on the screen. PHAS
ページ11に含まれる内容の要旨
MAINTENANCE If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel, inspect all system connections and cable runs. To reduce the risk of electrical shock, do not remove the cover or back of monitor. No user-serviceable parts are inside. Refer servicing to qualified personnel or contact the Pelco Technical Support Depart- ment for assistance. Refer to the Warranty and Return Information section. SPECIFICATIONS ELECTRICAL Input Voltage: 100-24
ページ12に含まれる内容の要旨
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. ® • Three years on Genex Series products (multiplexers, server, and keyboard). ® • Three years on Camclosure and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X,