ページ1に含まれる内容の要旨
MONITOR WITH DVD RECEIVER
DDX8029
INSTALLATION MANUAL
© B54-4535-00/00 (EV/E2V)
ページ2に含まれる内容の要旨
Accessories 1 ..........1 2 ..........1 3 ..........2 4 ..........1 5 ..........1 | 2 DDX8029
ページ3に含まれる内容の要旨
Installation Procedure 1. To prevent short circuits, remove the key from the € ignition and disconnect the - terminal of the • If the power is not turned ON (or it is ON, but will be OFF battery. immediately), the speaker wire may have a short-circuit 2. Make the proper input and output wire or touched the chassis of the vehicle and the protection connections for each unit. function may have been activated. Therefore, the speaker 3. Connect the wire on the wiring harness. wire should be c
ページ4に含まれる内容の要旨
Connection Connecter A Ground wire (Black) FUSE ( 5A ) Battery wire (Yellow) 8 6 4 2 7 5 3 1 Ignition wire (Red) 8 6 4 2 7 5 3 1 Accessory 4 (ISO-JASO) Connecter B Antenna Cord (ISO) (Orange/White) Dimmer control wire (Orange/White) Connect to the vehicle's parking brake detection switch harness ILLUMI using the supplied relay connector. Parking sensor wire (Light Green) PRK SW For the sake of safety, be sure to connect the parking sensor. Reveres sensor wire (Purple/White) To vehicle's reve
ページ5に含まれる内容の要旨
Rear view Cooling fan FM/AM antenna input FUSE ( 10A ) Accessory 1 REVERSE REMO.CONT MUTE ANT. CONT P CONT EXT.CONT | English 5
ページ6に含まれる内容の要旨
Connecting Wires to Terminals Connector Function Guide 2WARNING Pin Numbers for Cable Colour Functions Connecting the ISO Connector ISO Connectors The pin arrangement for the ISO connectors depends on External Power the type of vehicle you drive. Make sure to make the proper Connector connections to prevent damage to the unit. A-4 Yellow Battery The default connection for the wiring harness is described in A-5 Blue/White Power Control 1 below. If the ISO connector pins are set as described i
ページ7に含まれる内容の要旨
System Connection USB terminal (iPod) USB device (commercially available) USB terminal USB device (commercially available) iPod Do not connect. To Relay Box Accessory 2 Rear view ■ Audio/Visual input2 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Audio/Visual Output • Visual output (Yellow) ■ Audio/Visual input1 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Input • Visual input (Yellow) ■ Front Preout • Aud
ページ8に含まれる内容の要旨
iPod iPod AUDIO IN VIDEO IN Optional Accessory Connection iPod (commercially available) Navigation System (Optional Accessory) KCA-iP300V (Optional Accessory) Audio Input Connection cable Audio Output (Included in the Navigation System) (Black) Visual Input Visual Output (Yellow) Rear view USB terminal USB terminal (iPod) USB terminal iPod cannot be connected. Connection cable (Included in the Disc changer) Disc Changer etc. (Optional Accessory) TV Tuner (Optional Accessory) Connection cable
ページ9に含まれる内容の要旨
Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw Metal mounting strap (commercially available) (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installing the Escutcheon Accessory 5 | English 9
ページ10に含まれる内容の要旨
Removing Monitor/Player Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section . remove the two locks on the lower level. 2. Remove the Hex-head screw with integral washer Lower the frame and pull it forward as shown in (M4 × 8) on the back panel. the figure. 3. Insert the two removal tools 3 deeply into the Acce
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
