ページ1に含まれる内容の要旨
MONITOR WITH DVD RECEIVER
KVT-829DVD
INSTALLATION MANUAL
© B54-4555-00/00 (EV)
ページ2に含まれる内容の要旨
Accessories 1 0 ..........1 ..........1 2 ! ..........1 ..........2 3 @ ..........1 ..........1 4 ..........1 5 ..........1 6 ..........2 7 ..........4 8 ..........4 9 ..........2 | 2 KVT-829DVD
ページ3に含まれる内容の要旨
Installation Procedure 1. To prevent short circuits, remove the key from the € ignition and disconnect the - terminal of the • If the power is not turned ON (or it is ON, but will be OFF battery. immediately), the speaker wire may have a short-circuit 2. Make the proper input and output wire or touched the chassis of the vehicle and the protection connections for each unit. function may have been activated. Therefore, the speaker 3. Connect the wire on the wiring harness. wire should be c
ページ4に含まれる内容の要旨
iPod Connection Monitor/Player unit Do not connect. USB device (commercially available) USB connector (iPod) USB device (commercially available) USB connector Accessory ! Wiring harness (Accessory 2) Ground wire (Black) Ground wire (Black) The cable (Accessory 3) is FUSE ( 5A ) fixed with a chassis using Connector A harness band (Accessory Battery wire (Yellow) BATT !). 8 6 4 2 Ignition wire (Red) 7 5 3 1 ACC 8 6 4 2 Accessory 0 7 5 3 1 (ISO–JASO) Accessory 4 Connector B Antenna Cord (ISO)
ページ5に含まれる内容の要旨
Receiver unit Accessory ! The cable (Accessory 3) is fixed with a chassis using Accessory 3 harness band (Accessory !). Receiver unit FM/AM antenna input Wiring harness (Accessory 1) ILLUMI Ground wire (Black) - (To car chassis) A REVERSE REMO.CONT MUTE A ANT CONT P. CONT Battery EXT. CONT If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power sou
ページ6に含まれる内容の要旨
Connecting Wires to Terminals Connector Function Guide 2WARNING Pin Numbers for Cable Colour Functions Connecting the ISO Connector ISO Connectors The pin arrangement for the ISO connectors depends on External Power the type of vehicle you drive. Make sure to make the proper Connector connections to prevent damage to the unit. A-4 Yellow Battery The default connection for the wiring harness is described in A-5 Blue/White Power Control 1 below. If the ISO connector pins are set as described i
ページ7に含まれる内容の要旨
System Connection To Relay Box Accessory @ Receiver unit ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) • Audio right output (Red) ■ Audio/Visual input 2 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Audio/Visual input 1 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Inpu
ページ8に含まれる内容の要旨
iPod iPod iPod AUDIO IN VIDEO IN Optional Accessory Connection iPod (commercially available) KCA-iP300V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3.5Ф) Audio Output (Black) Visual Input Resistance-free mini plug (3.5Ф) Monitor/Player unit Visual Output (Yellow) USB terminal USB terminal (iPod) iPod cannot be connected. USB terminal Receiver unit Accessory 3 Connection cable Connection cable (Included in the Disc changer) (Included in the Navigation System) Disc C
ページ9に含まれる内容の要旨
Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw Metal mounting strap Accessory 5 (commercially available) (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installation for Receiver Unit 1. Attach the installation brackets 9
ページ10に含まれる内容の要旨
Removing Monitor/Player Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section . remove the two locks on the lower level. 2. Remove the Hex-head screw with integral washer Lower the frame and pull it forward as shown in (M4 × 8) on the back panel. the figure. 3. Insert the two removal tools 6 deeply into the Remo
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
