ページ1に含まれる内容の要旨
H-CMD4009
MULTIMEDIA DVD/CD/MP3 RECEIVER WITH BUILT-IN 3.5” TFT
DISPLAY AND TV TUNER
Instruction manual
DVD/CD/MP3-
3.5” TFT-
ページ2に含まれる内容の要旨
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents........................................................................................................................................2 Important safeguards..............................................................................
ページ3に含まれる内容の要旨
Important safeguards Using the device at temperature below -10º may cause the breakage of the device. Before using please heat up the passenger compartment to the recommended temperature! Read carefully through this manual to familiarize yourself with this high-quality car stereo system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage
ページ4に含まれる内容の要旨
Installation/Connection Installation 4
ページ5に含まれる内容の要旨
5
ページ6に含まれる内容の要旨
Electrical connection Caution: Do not interchange the connection of the wiring! For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit. 6
ページ7に含まれる内容の要旨
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. 3. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the color code table below for speaker and power cable connections. Function Connector A Connector B 1 7 Rear R
ページ8に含まれる内容の要旨
Panel controls Front panel 1. POWER/MU (mute) button 2. ANG (i.e. TILT) button 3. REL (Release) button 4. MODE button 5. TA button 6. VOL/SEL knob 7. AF button 8. TFT display 9. IR remote sensor 10. BAND button 11. UP and DN buttons 12. APS button 13. EJECT button 14. 1/PLAY/PAUSE button 15. 2/INT button 16. 3/RPT button 17. 4/RDM button 18. 5/-10 button 19. 6/+10 button 20. USB slot 21. RET(reset) button 22. AUX IN 23. SD/MMC slot 8
ページ9に含まれる内容の要旨
9
ページ10に含まれる内容の要旨
Remote control 1. EQ button – press to select the corresponding equalizer preset modes to adjust the sound quality. 2. PWR button - press it to turn the power on, press again to turn the power off. 3. MODE button - press it to select the mode: => TUNER => DISC (the type of disc in the unit) => USB => SD/MMC => AUX => TV =>. 4. MU button - press it to cut down the volume output, press it again or press +/- buttons to resume volume. 5. SEL button - press SEL button repeatedly to select the modes:
ページ11に含まれる内容の要旨
15. AUDIO button – In DVD mode press it to select audio language. In VCD mode press it to select the channel. 16. A-B button - press it to start repeating of the A-B fragment. 17. OSD button - Press it to show the information on display. 18. PROG button - During playback press this button to enter the program window. Use the buttons to select items of program list and adjust them. 19. P/N / BAND button – in Tuner mode press it to select the desired band. In DVD mode press it to choose T
ページ12に含まれる内容の要旨
During video CD playback press it to open the disc menu. 31. SUBTITLE button - Press it to select the subtitle language. 32. LOUD button - Press it to turn the LOUD function on or off. 33. STEP button - Press it consecutively to display the still frame forward with step by step. Changing the battery 1. Press the catch and at the same time pull out the battery tray. 2. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the
ページ13に含まれる内容の要旨
General operation Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press the RESET button on the panel to restore the unit to the original factory settings. Power on/off Press POWER button on the panel or PWR button on the RC to turn the unit on. Long press the POWER button on the front panel or briefly press the PWR button on the RC to turn the unit off. Note: After the unit is off, the volume level and radio current settings will
ページ14に含まれる内容の要旨
Mode control Press the MODE button on the panel or MODE button on the RC to select the different playing modes: => TUNER => DISC (the type of disc in the unit if there is any) => USB (if the USB device is inserted) => CARD (if the SD/ MMC card is inserted) => AUX => TV. Clock setting 1. Press the CLK button on the RC to show the clock on the display. 2. Press and hold for 2 seconds the CLK button, the hour will change its color. 3. Press the +/- buttons on RC or rotate the VOL knob on the panel
ページ15に含まれる内容の要旨
Digital tuner Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Band selection Press the MODE button on the panel or MODE button on the RC to select the TUNER mode. Press P/N / BAND button on the RC or BAND button on the panel once or more to select: FM1, FM2, FM3, AM1, AM2. Display will show the wave band, frequency and preset station number if already stored. Manua
ページ16に含まれる内容の要旨
Preset scan function Press the APS button to scan all preset stations in the memory of the current band and stay on each memory stations for about 5 seconds. To stop preset scan, press this button again. Auto memory store function Press the APS button on the panel and hold for 2 seconds to enter auto store mode. The radio will automatically store the 6 strongest available stations to the 6 preset memories of the current band. To stop auto store, press this button again. Mono/Stereo selection Pre
ページ17に含まれる内容の要旨
AF (Alternative Frequencies) function Press the AF button briefly to switch on/ off mode. Symbol “AF” will appear on the display. Note: The tuner will return to Alternative Frequencies whenever the reception signals getting worse. “Alarm” will be displayed when an emergency broadcasting is received. Meanwhile sound output level will be adjusted to the preset output level automatically when the volume control is set at minimum. PTY (Program Type) function 1. Press the PTY button on the RC to turn
ページ18に含まれる内容の要旨
Disc operations Disc glossary PBC (PlayBack Control) PBC is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc contains still images, it can playback high definition of still image. Title The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes possible to record several films on one disc. For example, if a disc contains three films, th
ページ19に含まれる内容の要旨
Picture file: JPEG (*.jpg) ISO 9660 or ISO 9660 +Joliet format - Max. 30 characters Max. Track number is 448 Max. nested directory is 8 levels The max. album number is 99 The max. length of each track is 99 minutes 59 seconds Supported sampling frequency for MP3 disc: 8 KHz – 48 KHz (44.1 KHz preferably) Supported bit-rates of MP3 disc are: 32 - 320 kbps (128 kbps preferably). Following formats are NOT supported *.ACC, *.DLF, *.M3U, *.PLS, MP3 PRO, files with DRM. Open session discs are
ページ20に含まれる内容の要旨
Note: USB format supports 2.0. Capacity: 8 MB ~ 1 GB. SD cards brands: Cannon, Fuji film, Palm, Motorola, Microsoft, IBM, HP, Compaq, Sharp, Samsung, etc. Capacity: 8 MB ~ 1 GB. MMC cards brands: Ericsson, Nokia, Motorola, HP, Palm, Sanyo, Microsystems, etc. Capacity: 16 MB ~ 1 GB. Loading a disc 1. Turn the power on. 2. Press the EJECT button on the panel to flip it down. Insert the disc with the printed side facing upward into the slot. Press EJECT button on the panel to eject the disc. The pa
