ページ1に含まれる内容の要旨
In Car Video
IVSC-5502
Operating and installation instructions
http://www.blaupunkt.com
ページ2に含まれる内容の要旨
CONTENTS General information ............... 11 Installation and safety notices ........ 11 Accessories .................................. 11 Supplied parts........................ 12 Switching on/off .................... 12 Switching on the signal controller .. 12 Switching off the signal controller .. 12 Settings .................................. 13 External monitor switch (Fig. 2)...... 13 Monitor connections ...................... 13 IR remote control ................... 13 Functions ......
ページ3に含まれる内容の要旨
GENERAL INFORMATION When doing so, observe the vehicle General information manufacturer’s safety notices (airbags, Thank you for choosing a Blaupunkt alarm systems, trip computers, immo- product. We hope you enjoy using this bilizers). new piece of equipment. Before drilling any holes, make sure that Please read these operating instruc- no installed cables or vehicle compo- tions before using the equipment for nents can be damaged. the first time. When installing the signal controller, The Blaup
ページ4に含まれる内容の要旨
SUPPLIED PARTS SWITCHING ON/OFF Supplied parts Switching on/off The signal controller is supplied with all Switching on the signal the parts listed below. Please check that controller the range of parts supplied with your The signal controller is switched on via device is complete. If one of the listed the “+12V ignition” switching line by the parts is missing, please contact your connected control device. dealer immediately. Switching off the signal ● Signal controller 7 607 003 551 controller
ページ5に含まれる内容の要旨
SETTINGS IR REMOTE CONTROL Settings IR remote control External monitor switch (Fig. 2) Functions Switch position on right: No external The supplied remote control is suitable monitor connected. for operating the signal controller and the monitors. Switch position on left: If a Blaupunkt navigation (RGB) monitor is connected You must enter a button combination via a Y-cable (7 607 001 600). in order to control a single monitor or all the monitors simultaneously. Monitor connections To do so, you
ページ6に含まれる内容の要旨
IR REMOTE CONTROL 1 POWER Settings for Audio OUT On/off button for the selected ; AUDIO CH • Arrow button / monitor or monitors. Select the input source for Audio OUT. 2 NAVI Selects the navigation monitor. Note: The volume of the input source must be adjustable. 3 VOL • arrow button Increase the volume for the se- < BOOSTER lected monitor (not Audio OUT). Setting the amplification for Audio OUT / 0 dB or 10 dB. VOL • arrow button Decrease the volume for the se- lected monitor (not Audio
ページ7に含まれる内容の要旨
INSTALLATION Note: Installation Before connecting the monitors to Installation and safety notices your signal controller, check that the +/- and switching positive connec- Before connecting your signal control- tions are working properly. ler, please read the following informa- tion carefully. Positive connection The battery’s negative terminal must Connect the fuse holder (1A fuse) to be disconnected for the entire time it protect the positive cable (permanent takes to install and connect this
ページ8に含まれる内容の要旨
INSTALLATION SPECIFICATIONS made to the vehicle, please contact Specifications a specialist workshop in your area. Video input: Note: Composite Video, 1.0 Vpp, 75 ohms You cannot display PAL video on the Audio input: wide vision TV monitor using the RGB 0 - 1.0 Vrms, 20 Hz-20 kHz input. (Booster off) In this case, the PAL video signal must be connected directly to the AV input of 0 - 0.3 Vrms, 20 Hz-20 kHz the wide vision TV monitor.. (Booster on) RGB input (video signal): 0.7 VPP, 75 ohms RGB i
ページ9に含まれる内容の要旨
SPECIFICATIONS Features 5 Audio inputs: Cinch jacks 4 Video inputs: Cinch jacks 1 RGB input: 15 pin Sub-D socket 4 monitor outputs: Composite video, audio L/R, control, 13-pin (8-pin) jack, with power, earth and switching positive 1 RGB output: 15-pin Sub-D plug-type connector 1 Audio output: Cinch jacks 10dB booster on/off Conversion: RGB to CCVS CCVS to RGB IR remote control IR receiver Power input: 4-pin plug-type connector Metal housing 17 DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO
ページ10に含まれる内容の要旨
12V Anschlussbilder • Connection diagrams • Schéma électrique • Schemi di allacciamento • Aansluittekeningen • Anslutningsbilder • Esquemas de conexión • Esquemas de ligação • Tilslutningsskemaer Fig. 1 Ext-monitor IR CH1 CH3 DC 12V IN CH5 RGB-IN AUDIO-IN CH2 CH4 +12V Ignition +12V Permanent (2) (Batterie, battery) (1) (3) Masse / GND 72
ページ11に含まれる内容の要旨
○○ ○○○○○○ Fig. 2 Ext-monitor IR CH1 CH3 DC 12V IN CH5 RGB-IN AUDIO-IN CH2 CH4 IR-Empfänger (Eingang) IR receiver in Audio in-right Video in Audio in-left Externer Monitorschalter Fig. 3 Audio OUT RGB OUT RL FRONT LEFT RIGHT OVERHEAD (right) (left) Audio OUT MONITOR MONITOR MONITOR MONITOR ○ ○ Navi- Monitor IVMS 5802 IVMS 6502 IVMR 9002 IVMR 1042 73 ○○○○○○ DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH DEUTSCH
ページ12に含まれる内容の要旨
74 Beispielanschluss mit verschiedenen Komponenten / Connection example with various components DX-N/V Monitor Car Radio DVD - Player (IVDP-01) 2x Aux-in Amplifier Preamp CDC AUX 2 DX-N/V out in in Digital RGB Video 3 AV 4 out in out in 1 1 2 Speakers 1 1 CDC-A08 5 IDC-A09 CDC out Audio Video 1 Audio L 1 OUT Audio R 1 RGB Anschlusskabel/Additional Cables: OUT Video 2 Audio L 2 Overhead 1 RCA-Cable 7 607 885 093 (1,3m) Audio R 2 M 4 Monitor
ページ13に含まれる内容の要旨
Service-Nummern / Service numbers / Numéros du service après- vente / Numeri del servizio di assistenza / Servicenummers / Telefonnummer för service / Números de servicio / Números de serviço / Servicenumre Country: Phone: Fax: WWW: Germany (D) 0180-5000225 05121-49 4002 http://www.blaupunkt.com Austria (A) 01-610 390 01-610 393 91 Belgium (B) 02-525 5454 02-525 5263 Denmark (DK) 44 898 360 44-898 644 Finland (FIN) 09-435 991 09-435 99236 France (F) 01-4010 7007 01-4010 7320 Great Britain (GB) 0
