ページ1に含まれる内容の要旨
SM-CMD2022
DVD/MP3/CD RECEIVER DVD/MP3/CD-
Instruction manual
ページ2に含まれる内容の要旨
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ....................................................................................................... 2 Important safeguards ................................................................................................. 3 Installa
ページ3に含まれる内容の要旨
Important safeguards Read carefully through the manual to familiarize yours with this high-quality sound system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. Do not attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes. Make sure that pins or other
ページ4に含まれる内容の要旨
Installation/ Connections First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. Before installing the unit, please remove two screws on the top. Before the installation 1. Remove the old unit from the dashboard. Remove the outer trim fram
ページ5に含まれる内容の要旨
On the masking tape mark the polarity of the speaker wires (+ & -), as well as left or right, and front or rear. Repeat this procedure for all of the speakers. Mark the power, ground, and any other wires also. Installation method A After inserting the holder into the dashboard, select the appropriate tab and bend them inwards to secure the holder in place. Insert fingers into the groove in the front of frame and remove it. Insert the levers supplied with the unit to the grooves at both sid
ページ6に含まれる内容の要旨
Use either truss screws (5 x 8mm) or flush surface screws (4 x 8mm), depending on the shape of the screw holes in the bracket. 2. Screw. 3. Factory radio mounting bracket. 4. Dashboard or Console. 5. Hook (Remove this part). Note: The mounting box, outer trim ring, and the Half-sleeve are not used for this method of installation. Detachable control panel Detaching the control panel 1. Press the OPEN button on the front panel. The panel will go down (pic. 1). 2. Push the panel to the left and the
ページ7に含まれる内容の要旨
Caution: DO NOT insert the control panel from the right side. It can damage the control panel. The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an Pic. 3 extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. Note: If the control panel is dirty, wipe off
ページ8に含まれる内容の要旨
Connection scheme: 8
ページ9に含まれる内容の要旨
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections. Location FUNCTION Connector A Connector B 1 Re
ページ10に含まれる内容の要旨
Accessories Name pcs 1 Hexagon nut M5 T (3.5 mm) 1 2 Mounting box (0.6 mm) 1 3 Left key (1.0 mm) 1 4 Right key (1.0 mm) 1 5 Metal bar (0.8 mm) 1 6 ISO connector 1 7 Plain washer =5 mm 1 8 Carrying case 1 9 Outer trim ring 1 10 Spring washer =5 mm 2 11 Screw 5X5 mm 4 12 Screw 5X25 mm 1 13 Screw M5 5X29.3 mm 1 14 Customer information 1 15 Warranty card 1 16 Instruction manual 1 10
ページ11に含まれる内容の要旨
Controls description Front panel 1. OPEN BUTTON Press it to remove the front panel. 2. TA BUTTON In RADIO mode press it to active the TA function. 3. / buttons In Disc mode press the buttons shortly to go to previous/next track. Press and hold them to start fast backward/ forward rewind. In Radio mode press the buttons shortly to search the stations manually. Press and hold for 2 seconds to start searching the stations automatically. 4. PTY / CLK BUTTON Press it and hold for 2 seconds to set c
ページ12に含まれる内容の要旨
6. / OSD button In menu use it to move to the left. During playback press it and hold for 2 seconds to show the mode information on the display. 7. / RPT BUTTON In menu use it to move to the right. During playback press it and hold for 2 seconds to start repeat playback. 8. / INT BUTTON In menu use it to move upward. During playback press it and hold for 2 seconds to start intro playback (about 10 seconds each track). 9. / RDM BUTTON In menu use it to move downward. During playback press it and
ページ13に含まれる内容の要旨
In Radio mode press it to scan the preset memorized stations. Press it and hold for 2 seconds to store the programs with the best reception into preset buttons automatically. 16. USB socket 17. SD/MMC socket 18. MUTE BUTTON Press it to switch the sound off/on. 19. VOL KNOB / SEL BUTTON Rotate it clockwise to increase the volume level; rotate anticlockwise to decrease the volume level. Press it repeatedly to select the mode: VOL => BAS => TRE => BAL => FAD => LOUD => LOC => ST => EQ. Rotate VOL k
ページ14に含まれる内容の要旨
Back of the front panel Press the OPEN button to open the panel. 1. LED INDICATOR 2. RESET BUTTON 3. DISK SLOT 4. EJECT BUTTON Note: Pressing the RESET hole will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down, flashes when you remove the panel. 14
ページ15に含まれる内容の要旨
Remote control 1. MODE BUTTON 2. POWER BUTTON 3. BND/SYS BUTTON 4. ERROR BUTTONS 5. ENTER BUTTON 6. STOP/REVERSE BUTTON 7. AMS/RPT BUTTON 8. ST/PROG BUTTON 9. LOC/RDM BUTTON 10. VOL +/- BUTTON 11. PBC BUTTON 12. OSD BUTTON 13. DIGIT AREA 14. PLAY/PAUSE BUTTON 15. MUTE BUTTON 16. TITLE BUTTON 17. SUB-T BUTTON 18. SETUP BUTTON 19. ANGLE BUTTON 20. SLOW BUTTON 21. ZOOM BUTTON 22. SEL BUTTON 23. SEEK +/- / / BUTTONS 24. AUDIO BUTTON 25. GOTO BUTTON 15
ページ16に含まれる内容の要旨
Changing the battery 1. Press the catch and at the same time pull out the battery tray. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. General operations Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press OPEN button and remove the panel, then press the RESET button to restore the unit to the original factory settings. Power butto
ページ17に含まれる内容の要旨
Mode selecting Press the MOD button on the front panel or MODE button on RC repeatedly to select the mode: RADIO => DISC (the type of disc inserted) => USB (if any is inserted) => CARD (the type of card inserted). Subwoofer control Press and hold the BAND/ NP/ SUB button on the panel to turn the Subwoofer output ON. An external amplifier is required to operate a subwoofer. Sound settings Press SEL button shortly and repeatedly to select the mode: VOL => BAS => TRE => BAL => FAD => LOUD => LOC =>
ページ18に含まれる内容の要旨
4. Press briefly the SEL button again, the minute will blink. 5. Rotate the VOL knob on the panel to adjust minutes. 6. Press the PTY/CLK button to confirm it. 18
ページ19に含まれる内容の要旨
Radio operations Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Band select Press the BAND button on the front panel or BND/SYS button on RC repeatedly to select your desired radio band during RADIO mode: FM1, FM2, FM3, AM1, AM2. Auto/ Manual tuning Manual tuning: Press briefly the SEEK-/+ buttons on the RC or press briefly / buttons on the panel to select a stat
ページ20に含まれる内容の要旨
APS (Auto memory store/ Preset scan) function Preset scan: press APS button on the panel or AMS button on the RC to scan all preset stations in the memory of the current band and stay on each memory stations for about 5 seconds. To stop preset scan, press this button again. To listen to saved station press 1-6 buttons. Auto memory store: press APS button on the panel for more than 2 seconds to enter auto store mode. The radio will automatically store the 6 strongest available stations to the 6
