ページ1に含まれる内容の要旨
SM-CMD2021
DVD/CD/MP3-RECEIVER DVD/CD/MP3-
Instruction manual
ページ2に含まれる内容の要旨
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents..........................................................................................................2 Installation/ Connections ...............................................................................................4 Acces
ページ3に含まれる内容の要旨
Important safeguards Read carefully through the manual to familiarize yours with this high-quality sound system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. Do not attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes. Make sure that pins or other
ページ4に含まれる内容の要旨
Installation/ Connections First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. Before installing the unit, please remove two screws on the top. Before the installation 1. Remove the old unit from the dashboard. Remove the outer trim f
ページ5に含まれる内容の要旨
Installation method A After inserting the holder into the dashboard, select the appropriate tab and bend them inwards to secure the holder in place. Insert fingers into the groove in the front of frame and remove it. Insert the levers supplied with the unit to the grooves at both sides. The unit can be installed or removed from the dashboard. Installation way (method 2) Installation using the screw holes at both sides of the unit. 1. Select a position where the screw holes of the main unit ar
ページ6に含まれる内容の要旨
Detachable control panel Detaching the control panel 1. Press the OPEN button on the front panel. The panel will go down (pic. 1). 2. Push the panel to the left and then pull it towards Pic. 1 Pic. 2 you (pic. 2). Attaching the control panel 1. Insert the left side of the control panel into the main unit (pic. 3). Note: the control panel must be attached into the T-Joint. 2. Press the right side of the control panel until a “click” sound is heard. Pic. 3 3. Close the panel. Caution: DO NOT inser
ページ7に含まれる内容の要旨
Electrical connections Speaker wiring notes Follow the above wiring diagram to install the head unit with new or existing speakers. This unit is designed for use with four (4) speakers with an impedance between 4 Ohms to 8 Ohms. An impedance load of less than 4 Ohms could damage the unit. Never bridge or combine the speaker wire outputs. When not using four speakers, use electrical tape to tape the ends of the unused speaker outputs to prevent a short circuit. Never ground the negative speak
ページ8に含まれる内容の要旨
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections. Location FUNCTION Connector A Connector B 1 Re
ページ9に含まれる内容の要旨
Accessories Name pcs 1 Hexagon nut M5 T (3.5 mm) 1 2 Mounting box (0.6 mm) 1 3 Left key (1.0 mm) 1 4 Right key (1.0 mm) 1 5 Metal bar (0.8 mm) 1 6 ISO connector 1 7 Plain washer =5 mm 1 8 Carrying case 1 9 Outer trim ring 1 10 Spring washer =5 mm 2 11 Screw 5X5 mm 4 12 Screw 5X25 mm 1 13 Screw M5 5X29.3 mm 1 14 Customer information 1 15 Warranty card 1 16 Instruction manual 1 9
ページ10に含まれる内容の要旨
Controls description Front panel 1. MODE button. Press it to select the mode: TUNER => DISC => AUX. 2. POWER BUTTON Press it to turn the power on/off. 3. VOL KNOB / SEL BUTTON Rotate it clockwise to increase the volume level; rotate anticlockwise to decrease the volume level. 10
ページ11に含まれる内容の要旨
Press it repeatedly to select the mode: VOL => BAS => TRE => BAL => FAD => LOUD => LOC => ST => EQ. Rotate VOL knob to adjust each mode. 4. LCD (LIQUID CRYSTAL DISPLAY) 5. TA BUTTON 6. PTY/CLK BUTTON Press it and hold for 2 seconds to set clock. 7. AF BUTTON 8. OPEN BUTTON Press it to remove the front panel. 9. / (NEXT/PREVIOUS) buttons In Disc mode press the buttons shortly to go to previous/next track. Press and hold them to start fast backward/ forward rewind. In Radio mode press t
ページ12に含まれる内容の要旨
In menu use it to move to the right. During playback press it and hold for 2 seconds to start repeat playback. 16. 1/ / OSD button In menu use it to move to the left. 17. APS BUTTON When press the APS button once, it will scan the preset station (1-6). When press and hold the APS button for 2 seconds, it will search all the strongest station and then save automatically (For FM and AM). 18. When SCAN button is pressed, the unit will search for the strongest signal for the nearby station. After th
ページ13に含まれる内容の要旨
Back of the front panel Press the OPEN button to open the panel. 1. LED INDICATOR 2. RESET BUTTON 3. DISK SLOT 4. EJECT BUTTON Note: Pressing the RESET hole will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down, flashes when you remove the panel. 13
ページ14に含まれる内容の要旨
Remote control 1. MODE BUTTON 2. POWER BUTTON 3. BND/SYS BUTTON 4. ERROR BUTTONS 5. ENTER BUTTON 6. STOP/REVERSE BUTTON 7. AMS/RPT BUTTON 8. ST/PROG BUTTON 9. LOC/RDM BUTTON 10. VOL +/- BUTTON 11. PBC BUTTON 12. OSD BUTTON 13. DIGIT AREA 14. PLAY/PAUSE BUTTON 15. MUTE BUTTON 16. TITLE BUTTON 17. SUB-T BUTTON 18. SETUP BUTTON 19. ANGLE BUTTON 20. SLOW BUTTON 21. ZOOM BUTTON 22. SEL BUTTON 23. SEEK +/- / / BUTTONS 24. AUDIO BUTTON 25. GOTO BUTTON 14
ページ15に含まれる内容の要旨
Changing the battery 1. Press the catch and at the same time pull out the battery tray. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. General operations Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press OPEN button and remove the panel, then press the RESET button to restore the unit to the original factory settings. Power butto
ページ16に含まれる内容の要旨
Mode selecting Press the MOD button on the front panel or MODE button on RC repeatedly to select the mode: RADIO => DISC (the type of disc inserted) =>. Subwoofer control Press and hold the BAND/ NP/ SUB button on the panel to turn the Subwoofer output ON. An external amplifier is required to operate a subwoofer. Sound settings Press SEL button shortly and repeatedly to select the mode: VOL => BAS => TRE => BAL => FAD => LOUD => LOC => ST => EQ. Rotate the VOL knob or use VOL +/- buttons to adju
ページ17に含まれる内容の要旨
Radio operations Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Band select Press the BAND button on the front panel or BND/SYS button on RC repeatedly to select your desired radio band during RADIO mode: FM1, FM2, FM3, AM1, AM2. Scan When SCAN button is pressed, the unit will search for the strongest signal for the nearby station. After the strongest signal is go
ページ18に含まれる内容の要旨
APS (Auto memory store/ Preset scan) function Preset scan: press APS button on the panel or AMS button on the RC to scan all preset stations in the memory of the current band and stay on each memory stations for about 5 seconds. To stop preset scan, press this button again. To listen to saved station press 1-6 buttons. Auto memory store: press APS button on the panel for more than 2 seconds to enter auto store mode. The radio will automatically store the 6 strongest available stations to the 6
ページ19に含まれる内容の要旨
TA (Traffic Alarm) function Press the TA button on the panel to select TA ON or TA OFF. In TA mode traffic program will be automatically searched, until the program is received. When traffic announcement is received the unit will temporarily switch to the tuner mode (regardless of the current mode) and begin broadcasting the announcement. After the traffic announcement is over, it will return to the previous mode and volume level. PTY (Program Type) 1. Press PTY/CLK button on the panel to activa
ページ20に含まれる内容の要旨
TA (Traffic Announcement) mode To determine what action will the radio take if the newly tuned station does not receive TP (Transport Program) information for 5 seconds. Rotate the VOL knob to select the desired mode: TA ALARM and TA SEEK. - TA SEEK When newly tuned station does not receive TP information for 5 seconds, the radio retunes to next station which has not the same station (PI – Program Information) as the last station, but has the TP information. When TP information gets lost at t
