ページ1に含まれる内容の要旨
VRCD220S
CD/MP3/WMA Player,
AM/FM Stereo Receiver with RDS,
Auxiliary Input and Detachable Face
VRCD220S English PROOF Manual.indd 1 VRCD220S English PROOF Manual.indd 1 10/15/08 11:34:09 AM 10/15/08 11:34:09 AM
ページ2に含まれる内容の要旨
Welcome! Dear Customer, CONGRATULATIONS. The VRCD220S CD/MP3/WMA Player, AM/FM Stereo Receiver with RDS, Auxiliary Input, Detachable Face and Speaker Kit when used as described, will give you years of dependable service in your car, truck, RV, or mini-van. We have taken numerous measures in quality con- trol to ensure that your product arrives in top condition and will perform to your satisfaction. In the rare event that your VRCD220S CD/MP3/WMA Player, AM/FM Stereo Receiver with RDS, Auxil
ページ3に含まれる内容の要旨
Precautions This unit will only play the following discs. Type of disc Label on the Disc Recorded Material Size of Disc CD Audio only 12 cm MP3/WMA N/A Audio only 12 cm • Do not attempt to modify the unit. • Do not operate in extremely high or low tem- • Modifying the unit will void the warranty. peratures. The temperature inside the vehicle • Stop the vehicle before carrying out any oper- should be between 32º F (0º C) and 100º F ation that could interfere with your driving. (37º C) before t
ページ4に含まれる内容の要旨
Notes on Installation • Disconnect negative battery terminal before starting installation. Consult the vehicle’s owner’s manual for proper instruction. • The unit is designed for a 12 Volt DC negative ground operation system only. Before installing the unit, make sure your vehicle is a 12 Volt DC negative ground system. • Mark the polarity of the existing speaker wires before disconnecting the old unit. • Be sure to connect the color coded leads according to the diagram. Incorrect connec- tion
ページ5に含まれる内容の要旨
Before You Install Automotive audio equipment installations can be challenging at times, even to the most experienced of installation technicians. If you are not confi dent working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other compo- nents of your vehicle, please call our toll-free help line 1-800-445-1797 and our in-house technical service team will answer your installation questions. Contact the vehicle's manufacturer for vehicle specifi c
ページ6に含まれる内容の要旨
Installation DIN FRONT-MOUNT (Method A) After inserting the Mounting Sleeve into the dashboard, select tabs on top, bottom, and sides, then bend them to secure the mounting sleeve in the dash board.(Fig. 1) Fig. 1 Follow the diagram in Fig. 2 for in- 1. Dashboard 2. Nut (5mm) stalling the rear mounting strap to 3. Spring washer the head unit. The rear mounting 4. Screw (5 x strap will help keep the head unit 25mm) 5. Screw from moving around inside the dash- 6. Strap board. 7. Plain w
ページ7に含まれる内容の要旨
Installation DIN REAR-MOUNT (Method B) Installation using the screw holes on both sides of the unit. 1. Screw holes on the side of the unit. 2. Screws. Use either truss screws (5 x 8mm) or fl ush surface screws (4 x 8mm), depending on the shape of the screw holes in the bracket. 3. Vehicle’s Factory Mounting Bracket 4. Dashboard or Console 5 Hook (Remove this part) Note: The mounting sleeve, outer trim ring, and the mounting strap are not used for this method of installation. PARTS 2 Keys 1
ページ8に含まれる内容の要旨
Installation WIRING CONNECTIONS GIVE US A CALL, WE'LL HELP YOU INSTALL. PLEASE DO NOT RETURN PRODUCT TO STORE. Visit us on the WEB www.vr-3.com For Information and Technical Assistance, Call Toll-Free in U.S.A. and Canada. 1-800-445-1797 7 VRCD220S English PROOF Manual.indd 8 VRCD220S English PROOF Manual.indd 8 10/15/08 11:34:15 AM 10/15/08 11:34:15 AM
ページ9に含まれる内容の要旨
Location of the Controls 12 34 5 6 7 8 21 20 19 18 17 16 15 14 13 12 11 10 9 1. Clock Button 14. Pre-set #5/Down 10 2. Mode Button 15. Pre-set #4/Random 3. Volume Up Button 16. Pre-set #3/Repeat 4. SEL Button 17. Pre-set #2/Intro 5. PTY Button 18. Pre-set #1/Pause/Play 6. LCD for Track Number, Time, Radio 19. TA Button Frequency, File Type, ID3, RDS, EQ 20. Volume Down Button 7. Open Faceplate Button 21. AF Button 8. Next Track/Change Frequency/Fast Forward 22. Eject button 9. Previous Track/Cha
ページ10に含まれる内容の要旨
Basic Operation 1. Turning the Unit On / Off 9. DSP-Preset Equalizer Function Press any button to turn the unit on, 1. Press and hold the “SEL” button until WELCOME will be displayed on the LCD to you hear a beep. indicate it is ready for use. Press and hold 2. Press the “SEL” button to cycle through the POWER button to turn the unit off. the menu choices until you see DSP OFF. 3. Press the +/- buttons to cycle 2. Mode Selection through the pre-set EQ settings. Press the MODE Button to cycle
ページ11に含まれる内容の要旨
Radio Operation 5. Press the +/- Buttons to adjust the vol- There are six numbered preset buttons ume level. which can store and recall stations for each 6. Leave the unit idle for the new setting to band. While listening to a radio station you take effect. The next time you turn the would like to save as a pre-set, press and unit ON, the volume will automatically hold one of the buttons numbered 1-6 until be adjusted to the sound level you set you hear a beep. The button you pressed here
ページ12に含まれる内容の要旨
RDS Operation station. This means you do not have to sound select button again so that the unit re-tune the radio when driving between will show “MASK DPI”. different transmitter coverage areas. When Press the “+/-” Buttons to toggle between AF is on, it means RDS information is “MASK DPI” and “MASK ALL” mode. Then received; when AF is flashing, it means leave the unit idle for the new setting to RDS information is not yet received. take effect. TA - Travel Announcements During “MASK DPI”
ページ13に含まれる内容の要旨
CD Operation Electronic Skip Protection - 12 or 45 Press this button again to resume play- seconds back. Electronic Skip Protection is ideal for driv- 4. Scanning Tracks ing on rough roads. Press the “SEL” Button Press the No.2/INT Button to play the first until the display will show “TA SEEK”. Then 10 seconds of each track. Press this but- press the “SEL” Button to cycle through ton again to resume playback. the menu until “ESP12” is displayed indi- cating that 12 seconds Electronic Skip 5
ページ14に含まれる内容の要旨
MP3 & WMA Disc Operation MP3 & WMA Disc Operation 4. Play/ Pause CD On the Head Unit, press the No.1 Button Electronic Skip Protection-120 Seconds to pause the CD. Press this button again Electronic Skip Protection is ideal for to resume playback. driving on rough roads. Electronic Skip Protection for MP3 & WMA CDs is a default 5. Scanning Tracks feature. Please note that this feature sup- On the Head Unit, press the No.2/INT ports CDs with Songs encoded by 96Kb/s Button to play the first 10
ページ15に含まれる内容の要旨
MP3 & WMA Disc Operation that “TRK” will blink on the display. AUX IN cable. Use the volume control to Then use the VOL +/- Button to choose adjust volume. your desired track and press the SEL Button again to confirm the selection. The 2. RCA Output selected track will be searched for and The RCA Output Jack is on the back of the then played. unit. (Refer to Wiring Diagram) This output is for connecting amplifier, equalizer, or 3. File Search other audio component that requires a Press the
ページ16に含まれる内容の要旨
Simple Troubleshooting Guide PROBLEM CAUSE/SOLUTION No Power Check wiring connections. Check and make sure the fuse is not blown. Replace with the proper rating/size fuse. Some errors occur in the LCD or Press the RESET Button. nothing functions when buttons are pressed. Unable to receive stations Check and make sure the antenna is con- nected properly. Poor radio reception Check and make sure the antenna is the correct length. Make sure the antenna is not broken. If the antenna is broken, re
ページ17に含まれる内容の要旨
Limited Warranty ® VIRTUAL REALITY SOUND LABS products are designed and manufactured to provide a high level of trouble- free performance. VIRTUAL REALITY SOUND LABS warrants, to the original purchaser, that its products are free from defects in material and workmanship for 30 days from the date of original purchase, as part of our commitment to product excellence. VIRTUAL REALITY SOUND LABS and/or it’s affi liates routinely improves the designs, materials or production methods of its existin
ページ18に含まれる内容の要旨
©2008 Intellectual Solutions Inc., All rights reserved. All designs, logos and images are the exclusive property of Intellectual Solutions Inc. and/or its affi liates. US and Foreign patents pending. 072208 Printed in China 00000 VRCD220S English PROOF Manual.indd 18 VRCD220S English PROOF Manual.indd 18 10/15/08 11:34:19 AM 10/15/08 11:34:19 AM
