ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Contents Precautions..............................................................................2 Notes on Installation.................................................................3 Before You Install.....................................................................4 Installation (DIN Front Mount)...................................................5 Installation (Vehicle's Brackets)................................................6 Wiring Connections......................................
ページ3に含まれる内容の要旨
Precautions • This unit will only play the following discs. Type of disc Label on the disc Recorded material Size of disc CD, MP3, WMA Audio only 12 cm Care of Discs • Do not use CDs with labels or stick- • Handle the disc by its edge to keep ers attached. The label may leave the disc clean. Do not touch the a sticky residue when it begins to disc’s surface. peel. • Clean the discs with an optional • Do not use a CD with paste or ink cleaning cloth. Wipe each disc from residue on it. the
ページ4に含まれる内容の要旨
Notes on Installation • Disconnect negative battery terminal before starting installation. Consult the vehicle’s owner’s manual for proper instruction. • The unit is designed for a 12Volt DC negative ground operation system only. Before installing the unit, make sure your vehicle is a 12Volt DC negative ground system. • Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicle's electrical system. • Be su
ページ5に含まれる内容の要旨
Before You Install Automotive audio equipment installations can be troublesome at times, even to the most experienced of installation technicians. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. IMPORTANT: Remove the two transport screws from the top of the unit before installing. 1. Remove the Old Unit fr
ページ6に含まれる内容の要旨
Installation WARNING! Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. NOTE: Mark the polarity of the existing speaker wires before disconnecting battery. NOTE: Remove the two transport screws from the top of the unit before installing. DIN Front Mount 1. After removing the old 2. Bend the tabs on the mount- radio and mounting sleeve, ing sleeve to keep the mount- insert supplied mount- ing sleeve f
ページ7に含まれる内容の要旨
Installation NOTE: Outer trim frame, hook, and mounting sleeve are not used for this installation. This is only intended as a general guide; contact the vehicle's manufacturer for specific instructions. This method of installation uses the screw holes at the sides of the unit and the holes of the existing vehicle mounting bracket. 1. Remove the hooks on both sides. 2. Align the screw holes of the mounting bracket supplied with the car and the screw holes of the main unit. Tighten the 2 scr
ページ8に含まれる内容の要旨
Wiring Connections Make sure that you have a good chassis ground. Good ground connections will eliminate most electrical noise problems. A good chassis ground requires a tight connec- tion to the vehicle's metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good electrical connection. Speaker Wiring Notes Follow the above wiring dia- • Never bridge or combine the gram to install the head unit speaker wire outputs
ページ9に含まれる内容の要旨
Front Panel Controls 8
ページ10に含まれる内容の要旨
VOL +/- Button to adjust the balance Basic Operation between the left & right speakers. Tuning the unit On / Off Fader Press any Button to turn the unit Press SEL Button five times and the on, the display will show a message display shows "FAD", then use the WELCOME to indicate it is ready for VOL +/- Button to adjust the balance use. Press the POWER button for 2 between the front & rear speakers. seconds to turn the unit off. Clock Mode Selection The time clock can be set anytime Press
ページ11に含まれる内容の要旨
Radio Operation Save Your Preset Stations There are six numbered preset but- Choose Radio Band tons which can store and recall sta- Press the BND•ID3 Button anytime to tions for each band. While listening to access the radio function. a radio station you would like to save The unit comes with five bands- three as a pre-set, press and hold one of the FM Bands (FM1, FM2, and FM3) buttons numbered 1-6 until you hear a and two AM Bands (AM1, and AM2) beep. The button you pressed is now selects
ページ12に含まれる内容の要旨
10 seconds of each track. Press this CD Operation(Cont) button again to resume playback. Repeat Insert/Eject CD On the Remote or Head Unit, press Insert a disc into CD slot with label the No.3/RPT Button to repeat the side up. The disc will be automati- same track continuously. “RPT ON" cally loaded into the unit, even when will appear on the display. Press this it is off or at radio mode. The word button again to stop repeating. “LOAD” will blink on the display and the CD will play aut
ページ13に含まれる内容の要旨
Selecting Tracks track. Press the Number 5 button to On the Head Unit, press the SEEK go back 10 tracks at once or press >>| Button to advance CD to the next the Number 6 button to advance 10 track. Track numbers will be shown tracks at once. on the display. Press and hold SEEK >>| to fast forward. Track Search Press the SEEK |<< Button to go Press the F/PS Button and the display to a previous track. Track numbers will show “TRK SCH”. Press the SEL will be shown on the display. Press
ページ14に含まれる内容の要旨
LCD. If there is no ID3 Tag informa- Auxilliary in, tion, nothing will shown on LCD. The sequence of ID3 Tag information will RCA out & be shown as follows: Subwoofer out (FILE) (FOLDER) MUSIC ALBUM ARTIST Auxiliary Input The Auxiliary Input Jack is on the pan- You can also press the BND/ID3 but- el of the unit. Insert the AUX IN cable's ton on the remote control to view the stereo plug into the AUX IN jack on the ID3 information anytime. panel of the unit. Route the other end of the ste
ページ15に含まれる内容の要旨
Infra Red Remote Control This unit comes with a full remote control system. The CR-2025 Lithium battery is an included item with the remote control. In case you have to replace the batteries (1) remove the cover from the back of the remote control. (2) insert a CR-2025 Lithium battery. (3) Fix the cover to the back of the remote control. Operating the remote control Aim at the face panel of the CD Receiver, the maximum dis- tance at which signals can be received is about 6M. Make sure that t
ページ16に含まれる内容の要旨
Simple Troubleshooting Guide PROBLEM CAUSE/SOLUTION Check wiring connections. Check and make sure the fuse is not No Power blown. Replace with the proper rating/size fuse. Press the RESET Button (21). Some errors occur in the LCD or nothing functions when buttons are pressed. Check and make sure the antenna Unable to receive stations is connected properly. Poor radio reception Check and make sure the antenna is the correct length. Make sure the antenna is not broken. If the antenna is b