ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-1005
APPLICATIONS
KIA Sedona 2002-2005
KIA Spectra 2002-2004
(2004 Base and LS models only)
99-1005
KIT FEATURES
• DIN Radio with Pocket Provision
• ISO Mount Radio with Pocket Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Snap In Brackets • C) Trim Plate • D) (4) Phillips Pan Head Screws
• E) Rear Support Bracket • F) Pocket
B C
D
A
E
F
TOOLS REQUIRED:
• Phillips Screwdriver
1-800-221-0932
www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS C
ページ2に含まれる内容の要旨
99-1005 TABLE OF CONTENTS Dash Disassembly - KIA Sedona 2002-2005 .... ........ ....... ........ ........ ........1 - KIA Spectra 2002-2004 (2004 Base and LS models only) . ...........2 DIN Radio Provision with Pocket ... ........ ........ ....... ........ ..3 ISO Mount Radio with Pocket Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Final Assembly .... ........ ....... ........ ........ ....... ........ .5 *Note: Refer also to the instructions included with the af
ページ3に含まれる内容の要旨
99-1005 DASH DISASSEMBLY KIA SEDONA 2002-2005 A 1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity. (Figure A) 3 Unclip and remove the small trim panel from around radio, climate con- trols and shifter. (Figure A) 4 Remove (4) Phillips screws from the radio trim panel then unclip and B remove the panel. (Figure B) 5 Remove (4) Phillips screws securing radio. Unplug and remove radio. (Figure
ページ4に含まれる内容の要旨
99-1005 DASH DISASSEMBLY KIA SPECTRA 2002-2004 (2004 Base and LS models only) *Note: Refer also to the instructions included with the aftermarket radio. A 1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Remove (2) Phillips facing up above gauge cluster. (Figure A) 3 Unsnap and remove top portion of steering wheel column cover. (Figure B) 4 Unsnap and remove entire panel from left side of steering wheel to right side surrounding radio. (Figure C) B 5 Remove
ページ5に含まれる内容の要旨
99-1005 KIT ASSEMBLY DIN RADIO WITH POCKET PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the pocket to the back of the radio housing using (2) of the screws supplied with the kit. (Figure A) 2 Mount the rear support bracket to the back of the pocket using the remaining (2) screws supplied with the kit. (Figure A) • Spectra only skip to final assembly. 3 Slide the DIN cage into the Radio B Housing and secure by bending the metal locking tabs outw
ページ6に含まれる内容の要旨
99-1005 KIT ASSEMBLY ISO MOUNT RADIO WITH POCKET PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the pocket to the back of the radio housing using (2) of the screws supplied with the kit. (Figure A) 2 Mount the rear support bracket to the back of the pocket using the remaining (2) screws supplied with the kit. (Figure A) 3 Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure B) B 4 Slide the radio i
ページ7に含まれる内容の要旨
99-1005 FINAL ASSEMBLY FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 (All Sedona and Spectra ISO mount radio only) Reassemble radio and das
ページ8に含まれる内容の要旨
99-1005 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 11/09/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-1005
