ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-8711
APPLICATIONS
Mercedes C-Class 2001-2004
Mercedes CLK 2004
99-8711
KIT FEATURES
• DIN Radio Provision with Pocket
• Stacked DIN Units Provision
KIT COMPONENTS
A) Radio Housing B) Pocket
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Torx Screwdriver
1-800-221-0932
www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
ページ2に含まれる内容の要旨
99-8711 TABLE OF CONTENTS Dash Disassembly - Mercedes C-Class 2001-2004 .... ........ ....... ........ ........ ...1 - Mercedes CLK 2004 .... ........ ....... ........ ........ ....... ....2 Kit Assembly - DIN Mount Radio Provision ...... ....... ........ ........ .... ... ... 3 - Stacked DIN Units Provision..... ........ ........ ....... ..... ... ... 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..5 *Note: Refer also to the instructions inc
ページ3に含まれる内容の要旨
99-8711 DASH DISASSEMBLY MERCEDES C-CLASS 2001-2004 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip shifter trim (with gear indica- tors). Unclip and remove center console 3 trim panel. (Figure A) 4 Remove the ashtray insert by releas- ing (2) plastic clips on the bottom lip of the ashtray assembly. (Figure B) B 5 Using a small flat screwdriver push the lower clip (“A”) inward and rotate the vent upward to expose (1) Torx head screw. Loosen the To
ページ4に含まれる内容の要旨
99-8711 DASH DISASSEMBLY MERCEDES CLK 2004 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery termi- A nal to prevent an accidental short cir- cuit. 2 Loosen shifter boot and pull up over shifter handle. (Figure A) 3 Turn the retainer on the shifter 1/2 turn to remove shifter handle and boot. (Figure B) 4 Unclip and remove the shifter trim panel. (Figure C) 5 Remove the ashtray insert by releasing (2) plastic clips on the bottom lip of
ページ5に含まれる内容の要旨
99-8711 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Slide the pocket into the radio housing until it snaps into place. (Figure B) Continue to final assembly. B 3
ページ6に含まれる内容の要旨
99-8711 KIT ASSEMBLY STACKED DIN UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cages into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket units into the cages until they snap into place. (Figure B) Continue to final assembly. B 4
ページ7に含まれる内容の要旨
99-8711 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
ページ8に含まれる内容の要旨
99-8711 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 10/20/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-8711
