Metra Electronics 99-8225Gの取扱説明書

ページ1に含まれる内容の要旨

INSTALLATION INSTRUCTIONS FOR PART 99-8225G
APPLICATIONS
Toyota Venza
2009-2010
99-8225G
KIT FEATURES
• DIN Head Unit Provision With Pocket
• ISO DIN Head Unit Provision With Pocket
• Painted to match factory dash - G=Gray
KIT COMPONENTS
• A) Single DIN Radio Housing • B) ISO Brackets • C) Trim Plate
B C
A
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• 70-1761 - 1987-up Toyota harness
• TYTO-01 - 2003-up Toyota JBL amp interface
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel

ページ2に含まれる内容の要旨

99-8225G TABLE OF CONTENTS Dash Disassembly - Toyota Venza 2009-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . .2 - ISO Din Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . 3 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognize

ページ3に含まれる内容の要旨

99-8225G DASH DISASSEMBLY Toyota Venza 2009-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel to the right of the shifter. (Figure A) 3 Remove (1) Phillips screw from the bottom of the climate control then unclip and remove the climate control. (Figure B) 4 Remove (4)10 MM bolts securing the radio. Note: You will need a univer- B sal swivel head socket adapter to get to the bottom left bolt. (Figure C) 5 Remove (4) Phil

ページ4に含まれる内容の要旨

99-8225G KIT ASSEMBLY DIN HEAD UNIT PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Secure the Radio Housing into the A factory a/c vent panel using the factory hardware. (Figure A) REAR VIEW - A/C VENT PANEL 2 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 3 Slide the DIN cage into the Radio H

ページ5に含まれる内容の要旨

99-8225G KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Secure the Radio Housing into the A factory a/c vent panel using the factory hardware. (Figure A) REAR VIEW - A/C VENT PANEL 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 3 Slide the head unit into the radio opening until the side clips engage. (Figure C) 4 Snap the Trim Plate into the Radio Housing. (Figure C)

ページ6に含まれる内容の要旨

99-8225G NOTES 4

ページ7に含まれる内容の要旨

99-8225G NOTES 5

ページ8に含まれる内容の要旨

99-8225G INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 05/20/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-8225G