ページ1に含まれる内容の要旨
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-18CV03(T3)
HSU-24CV03(T3)
Please read this operation manual before using the air conditioner
No.0010556977
ページ2に含まれる内容の要旨
Cautions Safety Instructions and Warnings Disposal of the old air conditioner Before disposing an old air conditioner that Before starting the air conditioner, read the goes out of use, please make sure it's inop- information given in the User's Guide caref- erative and safe. Unplug the air conditioner ully. The User's Guide contains very impor- in order to avoid the risk of child entrapment. tant observations relating to the assembly, operation and maintenance of the air It must be noticed t
ページ3に含まれる内容の要旨
Cautions 7. The appliance is not intended for use Do not obstruct or cover the ventilation by young children or infirm persons grille of the air conditoner.Do not put fingers without supervision. or any other things into the inlet/outlet and swing louver. 8. Young children should be supervised to ensure that they do not play with Do not allow children to play with the air the applience. conditioner.In no case should children be allowed to sit on the outdoor unit.
ページ4に含まれる内容の要旨
Cautions Safety Instruction Please read the following Safety Instructions carefully prior to use. The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use. Installation WARNING Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, wa
ページ5に含まれる内容の要旨
Cautions WARNING When abnormality such as burnt-small found, Use an exclusive power source with a immediately stop the operation button and circuit breaker contact sales shop. STRICT OFF ENFORCEMENT Connect power supply cord Use the proper voltage Do not use power supply cord to the outlet completely extended or connected in halfway STRICT STRICT PROHIBITION ENFORCEMENT ENFORCEMENT Take care not to damage Do not insert objects into the air Do not use power supply cord the power supply cord. in
ページ6に含まれる内容の要旨
Parts and Functions Indoor unit Outlet Display board Air filter(inside) Inlet UV light degerming Air Purifying Filter device (inside) (inside) Inlet grille Anion generator (inside) Vertical flap (adjust up and down air flow. Power plug Don't adjust it manually) Horizontal louver (adjust left and right air flow) For 24k unit, the power plug is on the outdoor unit Outdoor unit 1 1 1 1 4 4 2 2 3 3 HSU-18CV03(T3) HSU-24CV03(T3) 1 INLET 3 OUTLET CONNECTING PIPING AND ELECTRICAL WIRING 2 DRAIN HOSE
ページ7に含まれる内容の要旨
Parts and Functions 19 18 34 11 15 23 16 17 9. HEALTH button Used to set healthy operation. 10. ON/OFF button Used for unit start and stop. 11. TIMER ON display 12. FAN SPEED display LOW MED HI AUTO 13. LOCK display 14. SWING UP/DOWN display 28 FRESH 15. SLEEP display 16. HEALTH display 17.FRESH AIR display STERILIZE 18. Operation mode display Operation mode AUTO COOL DRY HEAT FAN 33 Remote controller Display board 19.Singal sending display 20. UV light degerming function display 21. Left/rig
ページ8に含まれる内容の要旨
Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in FRESH remote controller, clock should be adjusted as follows: 1. Press CLOCK button,"AM" or "PM" flashes. STERILIZE 2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly. 3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working. Remote controller's operat
ページ9に含まれる内容の要旨
Operation HEALTH operation Remote controller 1.Unit start Press ON/OFF on the remote controller, unit starts. Health function includes health anion function and UV light degerming function . 2.Health anion function Press HEALTH button. For each press, is displayed. Air conditioner starts health anion function operation. For twice press, disappears,the operation stops. 3.UV light degerming function Press STERILIZE button ," "and " "displayed on the remote controller and the air co
ページ10に含まれる内容の要旨
Operation Auto Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select Auto operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting FRESH increase 1 C,if kept depressed, it will increase rapidly STERILIZE Every time the button is pressed, temp.setting decrease 1 C,if
ページ11に含まれる内容の要旨
Operation Cool Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select COOL operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting FRESH increase 1oC,if kept depressed, it will increase rapidly STERILIZE Every time the button is pressed, temp.setting decrease 1oC,if
ページ12に含まれる内容の要旨
Operation Dry Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting FRESH increase 1oC,if kept depressed, it will increase rapidly STERILIZE Every time the button is pressed, temp.setting decrease 1oC,if ke
ページ13に含まれる内容の要旨
Operation Fan Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3.Fan speed selection Press FAN button. For each press, fan speed changes as follows: FRESH Remote controller: STERILIZE LOW MED HI 4.Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the u
ページ14に含まれる内容の要旨
Operation Heat Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting FRESH increase 1oC,if kept depressed, it will increase rapidly STERILIZE Every time the button is pressed, temp.setting decrease 1oC,if
ページ15に含まれる内容の要旨
Operation Air Flow Direction Adjustment 1.Status display of air sending Vertical flap Horizontal louvers Pos.1 Pos.1 Pos.2 Pos.2 Pos.3 Pos.3 FRESH Pos.4 Pos.4 STERILIZE Pos.5 Pos.5 Pos.6 Pos.6 (Auto swing) Pos.7 Pos.8 2.Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN remote controller: Pos.1 Pos.2 Pos.3 Pos.4 Pos.6 : HEAT: remote controller: Pos.5 Pos.4 Pos.3 Pos.2 P
ページ16に含まれる内容の要旨
Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. SLEEP operation starts SLEEP operation stops Use of SLEEP function Approx.6hrs After the unit starts, set the operation status, then press SLEEP button before which the Rises 1OC 1 hr clock must be adjusted and time being set. Operation Mode Rises 1OC 1 hr 1. In COOL,DRY mode 1 hours after SLEEP mode starts, temp. will Unit stop Temp.setting be
ページ17に含まれる内容の要旨
Operation Timer On/Off Operation Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode Remote Controller Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash. 3.
ページ18に含まれる内容の要旨
Operation Timer On-Off Operation Set clock correctly before starting TIMER operation. Remote Controller 1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON - OFF). " "will flash. 3.Time setting Press
ページ19に含まれる内容の要旨
Operation Health airflow Operation 1.Press ON/OFF to starting Remote controller The liquid crystal will display the working state of last time (Except timer, sleeping, power/soft and health airflow). Setting the comfort work conditions. 2.The setting of health airflow function 1).Press the button of health airflow, appears on the display. The nether inlet and outlet grills of the air condit- ioner are closed and the airflow is blown horizontally from the above inlet and outlet grills. Av
ページ20に含まれる内容の要旨
Operation Emergency and Test Operation Emergency operation: Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation. In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature. Operation Designated Timer Temperature Air flow mode temperature mode NO ABOVE 23OC COOLING 26OC AUTOMATIC AUTOMATI
