ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-6505
APPLICATIONS
Chrysler Multi Kit
99-6505
KIT FEATURES
• DIN Head Unit Provision with pocket
• ISO DIN Head Unit Provision with pocket
KIT COMPONENTS
A) Radio Housing • B) ISO Trim Plate • C) ISO Snap in Brackets
A C
B
TOOLS REQUIRED:
A) T orx # 20 • B) Phillips Screwdriver • C) Socket Wrench
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
ページ2に含まれる内容の要旨
99-6505 TABLE OF CONTENTS Dash Disassembly Chrysler 300M 1999-2004/Concorde 1998-2004/ Chrysler LHS 1998-2001/ Dodge Intrepid 1998-2004.............................1 Chrysler PT Cruiser. 2001-2005...............................................................1 Chrysler Sebring/Dodge Stratus 2001-2006.......................................... 2 Chrysler Town & Country/Voyager 2000-03/Dodge Caravan 2001-07 ..2 Dodge Neon 2000-2006/Plymouth Neon 2000-2001............................. 3 Dodge Ram 2
ページ3に含まれる内容の要旨
DASH DISASSEMBLY 99-6505 CHRYSLER 300M 1999-2004/CONCORDE 1998-2004 CHRYSLER LHS 1998-2001/DODGE INTREPID 1998-2004 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the ashtray by pressing down on the inner spring clip. (Concorde only) Unclip gear shifter trim panel and 3 slide trim panel toward the rear of the vehicle. 4 Unclip dash trim panel and discon- nect the wire to the trim panel. Remove (4) Phillips head screws 5 securing the radio. Disconnect
ページ4に含まれる内容の要旨
DASH DISASSEMBLY 99-6505 CHRYSLER SEBRING DODGE STRATUS 2001-2006 Disconnect the negative battery 1 terminal to prevent an accidental short circuit. 2 Remove (2) Phillips head screws from under the climate controls. Unclip and remove radio trim panel. 3 4 Remove (4) Phillips head screws securing the radio. Disconnect and remove the radio. Skip to kit assem- bly page. CHRYSLER TOWN & COUNTRYDODGE CARAVAN 2001-2007 CHRYSLER VOYAGER 2000-2003 1 Disconnect the negative battery terminal to prevent
ページ5に含まれる内容の要旨
99-6505 DASH DISASSEMBLY DODGE NEON 2000-2006 PLYMOUTH NEON 2000-2001 Disconnect the negative battery 1 terminal to prevent an accidental short circuit. 2 Pull off climate control knobs. Unclip and remove ac/heater vents. 3 4 Remove (1) Phillips head screw from each vent cavity. 5 Unclip and remove dash trim panel. 6 Remove (4) Phillips head screws securing the radio. Disconnect and remove the radio. Skip to kit assem- bly page. DODGE RAM 2002-2005 1 Disconnect the negative battery terminal t
ページ6に含まれる内容の要旨
99-6505 DASH DISASSEMBLY JEEP GRAND CHEROKEE 1999-2004 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove radio trim panel. 3 Remove (4) Phillips head screws securing the radio. Disconnect and remove the radio. Skip to kit assem- bly page. DODGE DAKOTA 2001-2004 DURANGO 2001-2003 1 Disconnect the negative battery 2 Screws terminal to prevent an accidental short circuit. 2 Remove (3) T-20 Torx screws from the bottom edge of the panel below the
ページ7に含まれる内容の要旨
99-6505 DASH DISASSEMBLY JEEP LIBERTY 2002-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove ashtray and remove one Phillips screw exposed. 2 3 1 4 3 Unclip and remove radio/ climate control panel. 4 Remove (4) Phillips screws securing radio. Disconnect and remove radio. Skip to kit assembly page. POWER OUTLET JEEP WRANGLER 2003-2006 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove defroster gr
ページ8に含まれる内容の要旨
99-6505 DASH DISASSEMBLY DODGE VIPER 2003-2009 Disconnect the negative battery 1 A terminal to prevent an accidental short circuit. 2 Using a small flat blade screw driver, pry up on center console trim panel. (Be careful not to scratch the trim panel) (Figure A) Loosen the shifter lock nut below 3 center console trim panel (Figure A) and unscrew the shifter knob. (Figure B) 4 Unplug electrical connectors and B remove center console trim panel. (Figure C) 5 Remove (6) Allen screws from radio/cl
ページ9に含まれる内容の要旨
99-6505 KIT ASSEMBLY DIN HEAD UNIT PROVISION A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) Slide the aftermarket head unit into 2 the cage and secure. (Figure B) B 7
ページ10に含まれる内容の要旨
99-6505 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION A 1 Align the holes in the ISO Snap In Brackets with the holes in the head unit and mount the brackets to the head unit with the screws supplied with the unit. (Figure A) Slide the head unit/bracket assembly 2 into the radio opening until the side clips engage. (Figure B) 3 Snap the ISO Trimplate over the head unit. (Figure B) B 8
ページ11に含まれる内容の要旨
99-6505 FINAL ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring
ページ12に含まれる内容の要旨
99-6505 INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-6505 REV. 05/04/10
