ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-7325
APPLICATIONS
Hyundai Santa Fe
2007-2010
(excludes 2010 NAV models)
99-7325
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing B) ISO Brackets C) Trim Plate
C
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
A
Harness:
• 70-7302 - Hyundai Harness 2007-up
• 70-7305 - Hyundai / KiA Harness 2009
Antenna Adapter:
• 40-KI11 - 2009-10 Santa Fe Adapter
TOOLS REQUIRED:
Small Flat Blade Screwdri
ページ2に含まれる内容の要旨
99-7325 TABLE OF CONTENTS Dash Disassembly - Hyundai Santa Fe 2007-2010 .. ........ ....... ........ ........ ......1 Kit Assembly - DIN Radio Provision with Pocket .... ....... ........ ........ . ...... 2 - ISO Radio Provision with Pocket .... ....... ........ ........ .. ..... .3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installa
ページ3に含まれる内容の要旨
99-7325 DASH DISASSEMBLY HYUNDAI SANTA FE 2007-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Remove (1) Phillips screw from the right side of the panel below the steering column then unclip and let right side of panel hang. (Figure A) Unclip and remove the cover above 3 the clock on top of panel surrounding the radio. (Figure B) 4 Unclip and remove the panel extend- B ing across the dash below the a/c control and above the glove box including the a
ページ4に含まれる内容の要旨
99-7325 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly. B 2
ページ5に含まれる内容の要旨
99-7325 KIT ASSEMBLY ISO RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 2 Slide the radio into the radio opening until the side clips snap into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly. B 3
ページ6に含まれる内容の要旨
99-7325 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
ページ7に含まれる内容の要旨
99-7325 NOTES 5
ページ8に含まれる内容の要旨
99-7325 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/27/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7325
