ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-7509
APPLICATIONS
Mazda 5 2006-2010
99-7509
KIT FEATURES
• Painted To Match Factory Dash
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Snap In Pocket
B
C
D
Wiring & Antenna Connections (sold separately)
A
70-7903 - Mazda Harness 01
ページ2に含まれる内容の要旨
99-7509 TABLE OF CONTENTS Dash Disassembly - Mazda 5 2006-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN/Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . 5 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
99-7509 DASH DISASSEMBLY MAZDA 5 2006-2010 For Models With Manual Climate Controls 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Unclip and remove the panel sur- rounding the shift lever. (Figure A) 3 Remove (2) Phillips screws exposed below shift lever trim panel. (Figure B) 4 Unclip and remove the center console side trim panels then remove (1) Phillips screw per side behind panels. B (Figure C,D) Continued on page 2. C D 1 A/C A/C P R N M-D
ページ4に含まれる内容の要旨
99-7509 DASH DISASSEMBLY MAZDA 5 2006-2010 For Models With Manual Climate Controls 5 Unclip and pull the center console E towards the rear of the vehicle. Note: You do not have to remove the center console completely. (Figure E) 6 Remove (2) Phillips screws at the bot- tom of the radio trim panel then unclip the panel including the factory radio. Unplug and remove the panel. Note: The climate controls do not come out with the panel. (Figure F,G) Continue to kit assembly. F G 2 A/C A/C
ページ5に含まれる内容の要旨
99-7509 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Slide the DIN cage into the Radio A Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. B C 3
ページ6に含まれる内容の要旨
99-7509 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Mount the ISO Brackets to the after- A market radio using the screws sup- plied with the radio. (Figure A) 2 Slide the radio into the Radio Housing until it snaps into place. (Figure B) 3 Snap the Trim Plate onto the front of the Radio Housing. (Figure C) 4 Snap the pocket into the Radio Housing. (Figure D) B Continue to final assembly. C D 4
ページ7に含まれる内容の要旨
99-7509 KIT ASSEMBLY DOUBLE DIN/STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Cut and remove the center bar from A the Radio Housing. (Figure A) 2 Snap the Double DIN Brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the Double DIN or stacked ISO unit(s) into the bracket/radio housing assembly and secure the Double DIN or stacked ISO unit(s) to the assembly using the screws supplied with the unit(s). (Figure C) B 4 Sna
ページ8に含まれる内容の要旨
99-7509 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassemb
ページ9に含まれる内容の要旨
99-7509 NOTES 7
ページ10に含まれる内容の要旨
99-7509 NOTES 8
ページ11に含まれる内容の要旨
99-7509 NOTES 9
ページ12に含まれる内容の要旨
99-7509 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/23/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7509
