Kenwood KOS-L702の取扱説明書

ページ1に含まれる内容の要旨

KOS-L702
WIDE TOUCH SCREEN MONITOR 7 page 2-11
INSTRUCTION MANUAL
MONITEUR ECRAN LARGE TACTILE 7 page 12-21
MODE D’EMPLOI
WIDE TOUCH SCREEN MONITOR 7 Seite 22-31
BEDIENUNGSANLEITUNG
BREEDBEELD MONITOR MET AANRAAKSCHERM 7 blz 32-41
GEBRUIKSAANWIJZING
MONITOR TOUCH SCREEN PANORAMICO 7 pagina 42-51
ISTRUZIONI PER L’USO
MONITOR DE PANTALLA TÁCTIL PANORÁMICA 7 página 52-61
MANUAL DE INSTRUCCIONES
MONITOR DE ECRÃ LARGO DE TOQUE 7 página 62-71
MANUAL DE INSTRUÇÕES
7

Take the time to read throu

ページ2に含まれる内容の要旨

Safety precautions 2 WARNING 2 CAUTION To prevent injury or fire, take the To prevent damage to the machine, take following precautions: the following precautions: • To prevent a short circuit, never put or leave any • Do not install the unit in a spot exposed to direct metallic objects (such as coins or metal tools) sunlight or excessive heat or humidity. Also avoid inside the unit. places with too much dust or the possibility of water splashing. • Do not watch or fix your eyes on the unit’

ページ3に含まれる内容の要旨

Notes • If you experience problems during installation, Screen brightness during low consult your Kenwood dealer. temperatures • When you purchase optional accessories, check When the temperature of the unit falls such as with your Kenwood dealer to make sure that they during winter, the liquid crystal panel’s screen will work with your model and in your area. become darker than usual. Normal brightness will return after using the monitor for a while. • If the unit fails to operate properly

ページ4に含まれる内容の要旨

Operations SRC/ MODE Auto Dimmer sensor PWR OFF V.SEL/ FUNC/ V.OFF AV OUT Switches the audio source ⁄ Controlling of optional A/V controllers is possible by Press the [SRC] button. touching the screen of this unit. Each time the button is pressed, the audio source Functions which can be controlled vary depending is changed. on the A/V controllers. Refer to the instruction ⁄ manual of the connected A/V controller for more • Refer to of

ページ5に含まれる内容の要旨

Switching Screen Mode Swithing the Display off mode Press the [MODE] button. You can set the display off mode for the monitor. Each time the button is pressed, the screen Press the [V.SEL] button for at least 1 second. mode switches as follows: Exit the Display off mode Display Setting Press any button. "Full" Full picture mode Press the button other than the [5] and [∞] buttons. "Zoom" Zoom picture mode Switches AV OUT source Selects an AV source to be output at the "AV "Just" Justify pict

ページ6に含まれる内容の要旨

Accessories 1 5 ..........1 ..........1 2 6 ..........1 ..........1 3 7 (Ø4 × 12 mm) ..........5 ..........1 4 ..........1 | 6 English

ページ7に含まれる内容の要旨

Installation Procedure 1. To prevent short circuits, remove the key from € the ignition and disconnect the · terminal of • If the fuse blows, first make sure that the wires have not the battery. caused a short circuit, then replace the old fuse with one 2. Make the proper input and output cable with the same rating. connections for each unit. • Do not let unconnected wires or terminals touch metal 3. Connect the wiring harness connector to the on the car or anything else conducting electr

ページ8に含まれる内容の要旨

Connection Monitor Unit Accessory 1 A/V controller (Optional accessory) (KOS-V500) MONITER POWER Connect the wiring harness referring to the instruction manual of the connected A/V controller. A/V controller (Optional accessory) (KOS-V1000) AV AV MONITOR MONITOR POWER POWER I/F IN 2 OUT 2 FM/ PRE AM OUT AV R-CAM IN 1 V-IN AV SUB REAR FRONT VIDEO VIDEO VIDEO OUT 1 MONITER POWER Connect the wiring harness referring to the instruction manual of the connected A/V controller. | 8 English

ページ9に含まれる内容の要旨

Installation Installation for Monitor Unit 5 Secure the stand using the supplied tapping screw (Accessory 3). Installation location and cleaning 6 After attaching the stand, allow it to sit Select for installation a location where the stand undisturbed for 24 hours. Take care not to apply can be placed completely horizontal or where the any force to the stand during this time. front edge of the support (petal-shaped part) can 7 I nsert the shoe of the monitor unit into the be attached hor

ページ10に含まれる内容の要旨

Installation Installation for Monitor Unit (For Headrest) Mounting and wiring this product requires skills and experience. For safety's sake, leave the mounting and wiring work to professionals. Before mounting the monitor to the headrest: • Perform the required external connections first (Accessory 1). • Using the supplied paper template (Accessory 7), mark the area to be cut out of the headrest, then carefully cut it. 1 Connect Monitor and system cord (Accessory 1). 2 Install the monitor uni

ページ11に含まれる内容の要旨

Troubleshooting Guide What might seem to be a malfunction in your unit ⁄ may just be the result of slight misoperation or • Refer to the instruction manual of the connected A/C miswiring. Before calling service, first check the controller for troubleshooting on the operation. following table for possible problems. ? The power does not turn ON. ✔ The motor is not attached to the bracket securely. ☞ Attach the motor to the bracket until it clicks. ? Nothing happens when the buttons are presse