ページ1に含まれる内容の要旨
DUAL DIN SIZED CD RECEIVER
DPX502U
DPX502UY
INSTRUCTION MANUAL
© B64-3829-00/00 (EW/E2W)
ページ2に含まれる内容の要旨
Contents Safety precautions 3 Menu system 24 Menu System Notes 4 Security Code Touch Sensor Tone General features 7 Manual Clock Adjustment Power Synchronize Clock Selecting the Source Display Illumination Control Volume Dimmer Attenuator Switching preout System Q Built-in Amp Setting Audio Control Dual Zone System Setting Adjusting the detail of Audio Control Supreme Setting Audio Setup AMP Control Speaker Setting News Bulletin with Timeout Setting Subwoofer Output Local Seek TEL Mute Tuning Mo
ページ3に含まれる内容の要旨
Safety precautions Do Not Load 8 cm (3 in.) CDs in the CD slot 2WARNING If you try to load a 8 cm (3 in.) CD with its adapter into To prevent injury or fire, take the following the unit, the adapter might separate from the CD and precautions: damage the unit. • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside About CD players/disc changers connected the unit. to this unit • Do not watch or fix your eyes on the unit’s display Kenwood
ページ4に含まれる内容の要旨
Notes • If you experience problems during installation, Cleaning the Unit consult your Kenwood dealer. If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. • When you purchase optional accessories, check with If the faceplate is stained badly, wipe the stain off with your Kenwood dealer to make sure that they work a cloth moistened with neutral cleaner, then wipe it with your model and in your area. again with a clean soft dry cloth. • The RDS fe
ページ5に含まれる内容の要旨
About Audio file About USB device • Playable Audio file • Install the USB device in the place where it will not prevent you from driving your vehicle properly. AA C-LC (.m4a), MP3 (.mp3), WMA (.wma), WAV (.wav) • You cannot connect a USB device via a USB hub. • Playable disc media • Take backups of the audio files used with this unit. The files can be erased depending on the operating CD-R/RW/ROM conditions of the USB device. • Playable disc file format We shall have no compensation for
ページ6に含まれる内容の要旨
Notes This Product is not installed by the manufacturer of a Handling CDs vehicle on the production line, nor by the professional • Do not touch the recording surface of the CD. importer of a vehicle into an EU Member State. • Do not stick tape etc. on the CD, or use a CD with tape stuck on it. • Do not use disc type accessories. Information on Disposal of Old Electrical • Clean from the center of the disc and move and Electronic Equipment (applicable for outward. EU countries that have ad
ページ7に含まれる内容の要旨
General features DISP Auxiliary input VOL Control knob ATT Q SRC Clock display LOUD indicator ATT indicator * An equipment such as a portable audio player can Power be connected to the auxiliary input terminal using a commercially available mini-plug (3.5ø). Turning ON the Power Press the [SRC] button. ⁄ • This unit automatically turns full power OFF after 20 ⁄ minutes lapses in Standby mode in order to save the • When the power is ON, the (page 25) is vehicle's battery. dis
ページ8に含まれる内容の要旨
General features Volume Audio Control Increasing Volume 1 Select the source to adjust Turn the [VOL] knob clockwise. Press the [SRC] button. Decreasing Volume 2 Enter Audio Control mode Turn the [VOL] knob counterclockwise. Press the [VOL] knob. 3 Select the Basic Audio item to adjust Press the [VOL] knob. Each time you press the knob, the item to be Attenuator adjusted alternates between the items shown in Turning the volume down quickly. the table below. Press the [ATT] button. 4 Adjust the
ページ9に含まれる内容の要旨
Adjusting the detail of Audio Control ⁄ • When you set the Bass Extend to ON, low frequency Among the Basic Audio items, you can adjust the Bass response is extended by 20%. level, Middle level, and Treble level in detail. • You can exit the Audio Control mode at anytime by pressing any button except for [VOL] knob and [ATT] 1 Select the Basic Audio item button. Select the desired item to be set in detail from followings; • Bass level • Middle level • Treble level For how to select Basic A
ページ10に含まれる内容の要旨
General features Audio Setup Speaker Setting Setting the Sound system, such as Cross over Fine-tuning so that the System Q value is optimal Network. when setting the speaker type. 1 Select the source to adjust 1 Enter Standby Press the [SRC] button. Press the [SRC] button. Select the "STANDBY" display. 2 Enter Audio Setup mode Press the [VOL] knob for at least 1 second. 2 Enter Speaker Setting mode Press the [VOL] knob. 3 Select the Audio Setup item to adjust Press the [VOL] knob. 3 Select the
ページ11に含まれる内容の要旨
TEL Mute The audio system automatically mutes when a call comes in. When a call comes in "CALL" is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON. When the call ends Hang up the phone. The "CALL" display disappears and the audio system comes back ON. ⁄ • To use the TEL Mute feature, you need to hook up the MUTE wire to your telephone using a commercial telephone accessory. Ref
ページ12に含まれる内容の要旨
General features • * When playing music from iPod or music edited by Switching Display "Music Editor", the folder name display may show Changing the information displayed. something different such as playlist or artist name depending on the music selection procedure. Press the [DISP] button. Each time the button is pressed the display switches as shown below. In Tuner source Information Display Program Service name or Frequency "FREQ/PS" (FM) Radio text, Program Service name or "R-TEXT" Fre
ページ13に含まれる内容の要旨
Tuner features FM Control knob AME AM SRC 1 - 6 Frequency display Band display ST indicator Preset station number Tuning Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUNER" display. 2 Select the band Push the Control knob towards [FM] or [AM]. Each time you push the knob toward [FM], it switches between the FM1, FM2, and FM3 bands. 3 Tune up or down band Push the Control knob towards [4] or [¢]. ⁄ • During reception of stereo stations the "ST" indicator is O
ページ14に含まれる内容の要旨
Tuner features Function of remote control Auto Memory Entry Direct Access Tuning Putting stations with good reception in the memory automatically. Entering the frequency and tuning. 1 Select the band for Auto Memory Entry 1 Select the band Push the Control knob towards [FM] or [AM]. Press the [FM] or [AM] button. 2 Enter Direct Access Tuning mode 2 Open Auto Memory Entry Press the [DIRECT] button on the remote Press the [AME] button for at least 2 seconds. control. "A-MEMORY" is displayed. "– –
ページ15に含まれる内容の要旨
RDS features Control knob TI SRC 1 - 6 Radio text RDS indicator TI indicator PTY indicator Receiving other traffic information stations Traffic Information Push the Control knob towards [4] or [¢]. Changing to traffic information automatically when ⁄ a traffic bulletin starts even when you are not • Traffic information can be switched when it is on the listening to the radio. Tuner Source. However, you cannot switch the Traffic Press the [TI] button. information during reception of the Traff
ページ16に含まれる内容の要旨
RDS features PTY (Program Type) ⁄ • Speech and Music include the Program type shown Selecting the Program Type and searching for a below. station. Music: No.12 — 17, 26 — 30 Speech: No.3 — 11, 18 — 25, 31 1 Enter PTY mode • You can put the Program Type in the [1] — [6] button Press the Control knob. memory and for quick recall. Refer to the (page 16). ⁄ • You can change the display language. Refer to
ページ17に含まれる内容の要旨
Changing Language for PTY Function Selecting the Program Type display language. 1 Enter PTY mode Refer to (page 16). 2 Enter Changing Language mode Press the [TI] button. 3 Select the language Push the Control knob towards up or down. Each time you push the knob, the language alternates between the languages shown in the table below. Language Display English "ENGLISH" French "FRENCH" Swedish "SWEDISH" German "GERMAN" 4 Exit Changing Language mode Press the [TI] button. | E
ページ18に含まれる内容の要旨
CD/USB device/Audio file/External disc control features Control knob USB connector SRC S.MODE SCAN RDM/3/ REP F.SEL M.RDM A.RDM Track number Play time IN indicator Disc number Playing CD & Audio file USB Device Connection 1 Remove the cap and connect the When a disc is inserted USB cable. Press the [SRC] button. 2 Connect the USB device to the unit Select the "CD" display. using the USB cable. ⁄ • When a CD is inserted, the "IN" indicator is ON. Pause and play Press the Control knob. Each time
ページ19に含まれる内容の要旨
Playing USB (iPod) device Drive Search Selecting the device inserted in the Multi Card When the USB device is not connected Reader. Connect the USB device 1 Put the playback to pause Playback of the file contained in the USB device Press the [S.MODE] button. starts. 2 Select a device When the USB device is connected Push the Control knob towards up or down. Select USB source 3 Restart playback Press the [SRC] button. Press the [S.MODE] button. Select the "USB" (or "iPod") display. ⁄ ⁄ • This
ページ20に含まれる内容の要旨
CD/USB device/Audio file/External disc control features Function of disc changer/ Audio file Playing External Disc Disc Search/Folder/Album Search Playing discs set in the optional accessory disc player connected to this unit. Switching between folders/albums contained in the disc in the disc changer, media, or device being Press the [SRC] button. played now. Select the display for the disc player you want. Display examples: Push the Control knob towards up or down. Display Disc player "CD C
