ページ1に含まれる内容の要旨
HSM09RU03/R2(DB)
HSM09RU03/R2(DB)
2HUM18R03/R2(DB)
HSM09RU03/R2(DB)
HSM12RU03/R2(DB)
2HUM18R03/R2(DB)
No, 0010503373
ページ2に含まれる内容の要旨
Contents Cautions 2 Parts and functions 6 Operation 9 Maintenance 22 Trouble shooting 27
ページ3に含まれる内容の要旨
Cautions Disposal of the old air conditioner Safety Instructions and Warnings Before disposing an old air conditioner that Before starting the air conditioner, read the goes out of use, please make sure it's inop- information given in the User's Guide caref- erative and safe. Unplug the air conditioner ully. The User's Guide contains very impor- in order to avoid the risk of child entrapment. tant observations relating to the assembly, operation and maintenance of the air conditioner. It must be
ページ4に含まれる内容の要旨
Cautions 7. The appliance is not intended for use Do not obstruct or cover the ventilation by young children or infirm persons grille of the air conditoner.Do not put fingers without supervision. or any other things into the inlet/outlet and swing louver. 8. Young children should be supervised to ensure that they do not play with Do not allow children to play with the air the applience. conditioner.In no case should children be allowed to sit on the outdoor unit. 9.Ple
ページ5に含まれる内容の要旨
Cautions Safety Instruction Please read the following Safety Instructions carefully prior to use. The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use. Installation WARNING Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water
ページ6に含まれる内容の要旨
Cautions WARNING When abnormality such as burnt-small found, Use an exclusive power source with a immediately stop the operation button and circuit breaker contact sales shop. STRICT OFF ENFORCEMENT Connect power supply cord Use the proper voltage Do not use power supply cord to the outlet completely extended or connected in halfway STRICT STRICT PROHIBITION ENFORCEMENT ENFORCEMENT Take care not to damage Do not insert objects into the air Do not use power supply cord inlet or outlet. in a bun
ページ7に含まれる内容の要旨
Parts and Functions Indoor unit Air Purifying Filter Outlet (inside) Inlet Air filter(inside) Inlet grille UV light degerming display board(inside) device (inside) Vertical flap Anion generator (adjust up and down air flow. (inside) Don't adjust it manually) Horizontal louver(inside) (adjust left and right air flow) Outdoor unit 1 3 OUTLET CONNECTING PIPING AND ELECTRICAL WIRING 2 4 INLET DRAIN HOSE 6
ページ8に含まれる内容の要旨
Parts and Functions 19 20 8. HOUR button Used to set clock and timer setting. 9. HEALTH AIRFLOW button 21 Used to set the health airflow mode. 22 10. HEALTH button Used to set healthy operation. 23 11. ON/OFF button 24 Used for unit start and stop. 12. TIMER ON display 25 13. FAN SPEED display TEMP 26 LOW MED HI AUTO 27 14. LOCK display HEALTH FAN 26 15. SWING UP/DOWN display SWING 28 16. SLEEP display MODE H.AIR. 29 17. HEALTH display SLEEP FRESH 18.FRESH AIR display 30 CLOCK SET 31 19. Operat
ページ9に含まれる内容の要旨
Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: 1. Press CLOCK button,"AM" or "PM" flashes. 2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly. 3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working. Remote controller's operation When in use, p
ページ10に含まれる内容の要旨
Operation HEALTH operation 1.Unit start Remote controller Press on/off button (" ") on the remote controller, unit starts. Health function includes health anion function, UV light degerming function. 2.Health anion function Press HEALTH button. For each press, is displayed. Air conditioner starts health anion function operation. For twice press, disappears,the operation stops. When indoor fan motor is running, it has healthy process function. (It's available under any mode) Whe
ページ11に含まれる内容の要旨
Operation Auto Operation 1. Unit start Remote controller Press on/off button (" ") on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select Auto operation 3.Select temp.setting TEMP Press TEMP. button Every time the button is pressed, temp.setting o increase 1 C,if kept depressed, it will increase rapidly HEALTH FAN Every time the button is pressed, temp.setting S
ページ12に含まれる内容の要旨
Operation Cool Operation 1. Unit start Remote controller Press on/off button (" ") on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select COOL operation TEMP 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting HEALTH FAN o increase 1 C,if kept depressed, it will increase SWING rapidly MODE H.AIR. Every time the button is press
ページ13に含まれる内容の要旨
Operation Dry Operation Remote controller 1. Unit start Press on/off button (" ") on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation TEMP 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting o HEALTH FAN increase 1 C,if kept depressed, it will increase rapidly SWING MODE H.AIR. Every time the button is pressed
ページ14に含まれる内容の要旨
Operation Fan Operation 1. Unit start Remote controller Press on/off button (" ") on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation TEMP 3.Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: HEALTH FAN LOW MED HI SWING H.AIR. MODE 4.Unit stop SLEEP FRESH Press on/off button(" "), the unit
ページ15に含まれる内容の要旨
Operation Heat Operation 1. Unit start Remote controller Press on/off button (" ") on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation TEMP 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting o increase 1 C,if kept depressed, it will increase HEALTH FAN rapidly SWING Every time the button is pressed, temp.set
ページ16に含まれる内容の要旨
Operation Air Flow Direction Adjustment 1.Status display of air sending Vertical flap Horizontal louvers Pos.1 Pos.1 Pos.2 Pos.2 TEMP Pos.3 Pos.3 Pos.4 HEALTH FAN Pos.4 SWING MODE H.AIR. Pos.5 Pos.5 SLEEP FRESH CLOCK SET Pos.6 Pos.6 TIMER (Auto swing) Pos.7 LOCK LIGHT CODE RESET Pos.8 2.Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN Pos.1 Pos.2 Pos.3 Pos.4 Pos.6 remo
ページ17に含まれる内容の要旨
Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. SLEEP operation starts SLEEP operation stops Use of SLEEP function Approx.6hrs After the unit starts, set the operation status, then press SLEEP button before which the O Rises 1 C 1 hr clock must be adjusted and time being set. Operation Mode O Rises 1 C 1 hr 1. In COOL,DRY mode 1 hours after SLEEP mode starts, temp. will Unit stop O Temp.settin
ページ18に含まれる内容の要旨
Operation Timer On/Off Operation Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode Remote Controller Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash. 3.T
ページ19に含まれる内容の要旨
Operation Timer On-Off Operation Set clock correctly before starting TIMER operation. Remote Controller 1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON - OFF). " "will flash. 3.Time setting Press H
ページ20に含まれる内容の要旨
Operation POWER/SOFT Operation POWER Operation When you need rapid heating or cooling, you can use this function. Remote controller Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed,display changes as follows: BLANK SOFT POWER Stop the display at In POWER operation status: In HEAT or COOL mode, compressor runs in high frequency for 15 min then returns to original status setting. TEMP To cancel POWER operation Press POWER/SOFT button twice ,POWER/SOFT disappea
