Boston Acoustics GT-40の取扱説明書

デバイスBoston Acoustics GT-40の取扱説明書

デバイス: Boston Acoustics GT-40
カテゴリ: カーオーディオ
メーカー: Boston Acoustics
サイズ: 0.63 MB
追加した日付: 8/28/2014
ページ数: 19
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスBoston Acoustics GT-40の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Boston Acoustics GT-40に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Boston Acoustics GT-40をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Boston Acoustics GT-40のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Boston Acoustics GT-40の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Boston Acoustics GT-40 取扱説明書 - Online PDF
Advertisement
« Page 1 of 19 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Boston Acoustics GT-40を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Boston Acoustics GT-40の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 1
GT-40
4-Channel, High-Current/High-Power Amplifier
On
Safe
Status

ページ2に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 2 Table of Contents Parts List 3 Features and Specifications 3 Control Functions 4 Control functions (cont.) 5 Control functions (cont.) 6 Mechanical Functions 6 Control cover removal & reinstallation 6 Multi-position mounting feet 6 Mechanical functions (cont.) 7 Amplifier linking 7 Wire connection 7 Fuses 7 General Installation Precautions 8 Before you install 8 Battery & charging system 8 Wire routing 8 Installation—Amplifier Mounting 9 Choose the mounting lo

ページ3に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 3 Parts List Included Hardware (1) owner’s manual (1) female quick-connect terminal for remote input (1) 2mm hex wrench (for speaker input) (1) 3mm hex wrench (for power input) (4) mounting screws Features and Specifications GT-40 Features 4-Channel, High-Current Amplifier Continuously Variable Crossover and Q-factor Settings 2 Ω Bridge Stable Operation Selectable Highpass Front Channels Power Increase with Input Voltage Rise Selectable Mono/Stereo Rear Highpas

ページ4に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 4 Control Functions 3 5 9 12 10 6 4 4 11 1 7 2 8 12 1 FRONT RCA Inputs RCA cables marked “FRONT” from head unit or from other line level device 1 should be connected here. Use both inputs (L & R) for stereo. 2 2 FRONT Remote Input Use the supplied FEMALE quick connector to connect the REMOTE trigger lead from the head unit to the amplifier. Amplifier turns “ON” when head unit is turned “ON.” One FEMALE .210" connector is supplied with amplifier. 3 FRONT Input Sw

ページ5に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 5 Control Functions (cont.) 6 “Q” Control “Q” Control is active when the highpass crossover is engaged and is centered on the selected crossover point. The range of operation is 0.7–1.2. dB Q +1.6dB 0dB -3dB .707 .95 1.2 t (tuned crossover frequency) 7 REAR RCA Inputs RCA cables marked “REAR” from head unit or other line level device should be 7 connected here. Use both inputs (L & R) for stereo. 8 8 REAR Remote Input This remote input is parallel to the FRON

ページ6に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 6 Control Functions (cont.) 12 Subwoofer Level Control Port Switch should be set to “OFF” when control circuit is not installed, (see optional “subwoofer level control” owner’s manual). cover panel Mechanical Functions Recessed RCA Inputs The input jacks are recessed into the body of the amplifier to provide clear- ance in tight mounting locations. 1 inch 1 inch Control Cover Removal & Reinstallation The cover panel is secured with two (2) captive coin-slotted

ページ7に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 7 Mechanical Functions (cont.) Amplifier Linking The design of the side panels enables multiple amplifiers to be used together without additional hardware. Wire Connection Amplifier accepts stripped wire directly into the terminal blocks. Speaker outputs accept 8-gauge, and the DC power and ground accept 4-gauge. Tighten with supplied hex wrenches. Fuses Amplifier accepts standard AT-style automotive blade fuses. 7

ページ8に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 8 General Installation Precautions WARNING! Before driving the amplifier mounting screws through any surface, be sure of what is behind that surface. Check for the gas tank, brake lines, and any vehicle wiring harness. Never run wires outside or under the vehicle or where they could become broken or interfere with the safe operation of the vehicle. Before You Install Before you install the unit, disconnect the negative (–) battery cable in the engine compartm

ページ9に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 9 Installation—Amplifier Mounting Choose the Mounting Location Plan your installation so that the amplifier is mounted where adequate ventilation is available. Never mount an amplifier in the engine compartment of a vehicle! WARNING! Before driving the mounting screws through any surface, be sure of what is behind that sur- face. Check for gas tank, brake lines, and any vehicle wiring harness. 1 13mm ( /2”) 7 225mm (8 /8”) 1 57mm (2 /2”) 1 358mm (14 /8”) 9

ページ10に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 10 Installation—Amplifier Mounting (cont.) Passenger & Trunk Compartment Mounting If the amplifier is mounted under a seat, be sure that the vents do not become blocked. Do not allow seat padding or other obstructive material to press down on the amplifier. All Boston GT amplifiers have top panel controls. If the amplifier is mounted under a seat, position the amplifier so the cover panel can be removed with the seat forward or back to allow adjustment of the audi

ページ11に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 11 Installation—Fuses & Wiring (cont.) Power/B+ & Power/GND Connection 5 Strip approximately /8" (16mm) of insulation. The positive (+) power wire is installed into the amplifier terminal marked “B+.” The negative (–) wire 1 / " 4 is installed into the terminal marked “GND.” The ground wire should be as short as possible and connected directly to the chassis of the vehicle. Make sure that the chassis connection point is free of rust, grease, dirt, paint, and o

ページ12に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 12 Installation—Fuses & Wiring (cont.) Mono Subwoofer Operation If the amplifier is to be bridged and used with a subwoofer connected to the REAR channels, use the “SPEAKER OUTPUT” terminals marked for mono use. WARNING! Subwoofer impedance must not fall below 2 ohms when in MONO mode. 2-ohm minimum Setup Tuning—Full-range Speakers 1) Music The material chosen for head unit/amplifier system setup must be both clear in recording quality and dynam- ic in amplitud

ページ13に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 13 Setup Tuning—Full-range Speakers (cont.) 4) Head Unit The head unit should have all controls such as bass, treble, balance, and fader set to the flat or centered position. The volume control should be at the minimum setting. If the head unit has any equalization or bass management features such as boost, they should be defeated at this time. Turn head unit on, and verify that the GREEN status LED is lit on the amplifier. 5) Volume With the chosen musical tra

ページ14に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 14 Setup Tuning—Full-range Speakers (cont.) 8) FRONT “Q” Control Once the FRONT highpass crossover point has been determined, use the FRONT “Q” control to increase the bass information centered around the crossover point. Setting the front “Q” control is done in conjunction with setting the levels on the input sensitivity and highpass crossover frequency controls. You may find while setting the “Q” that bottoming may be detected in the front speakers; lowering

ページ15に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 15 Setup Tuning—Subwoofers (cont.) 3) Head Unit The head unit should have all controls such as bass, treble, balance, and fader set to the flat or centered position. The volume control should be at the minimum setting. If the head unit has any equalization or bass management features such as boost, they should be deactivated at this time. Turn head unit on, and verify that the GREEN status LED is lit on the amplifier. 4) Volume With the chosen musical track pl

ページ16に含まれる内容の要旨

6.5LF 6.5LF 6.5LF 6.5LF GT-40_manual 4/10/03 4:17 PM Page 16 System Examples System A—Full-range Front with Full-range Rear to ground fuse to + battery terminal System B—Full-range Front with Rear Fill to ground fuse to + battery terminal 16 6.5LF 6.5LF 6.5LF 6.5LF

ページ17に含まれる内容の要旨

6.5LF 6.5LF GT-40_manual 4/10/03 4:17 PM Page 17 System Examples (cont.) System C—Main Speakers with Single Subwoofer (2 Ω) to ground fuse to + battery terminal 2Ω 10.5LF System D —Main Speakers with Parallel 4 Ω Subwoofers (2 Ω load) to ground fuse to + battery terminal 4Ω 4Ω 10.5LF 10.5LF 17 6.5LF 6.5LF

ページ18に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 18 Amplifier Troubleshooting Guide Status LEDs on Amplifier not Lit—Head Unit (Source) Turned “ON” Verify Remote turn-on wire from source to amplifier has proper voltage Power (B+) connections at amplifier, terminal blocks, and battery are secure Ground (GND) connections at amplifier and vehicle chassis are secure Battery B+ fuse is OK Amplifier fuse is OK B+ at battery and B+ at amplifier have proper voltage Status LEDs Lit, no Output from Speakers—Speakers in Norm

ページ19に含まれる内容の要旨

GT-40_manual 4/10/03 4:17 PM Page 19 Contact and Warranty Information Limited Warranty (US) For one (1) year from the date of purchase, Boston Acoustics will repair for the original owner any defect in materials or workmanship that occurs in normal use, without charge for parts and labor—when purchased from an authorized Boston Acoustics retailer. If an authorized Boston Acoustics retailer installs your amplifier, the warranty will be extended one (1) additional year. Installation of the ampli


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Boston Acoustics GT-42 取扱説明書 カーオーディオ 68
2 Boston Acoustics RX57DIN 取扱説明書 カーオーディオ 0
3 Boston Acoustics RX67DIN 取扱説明書 カーオーディオ 0
4 Boston Acoustics GT-50 取扱説明書 カーオーディオ 38
5 Sony Bluetooth 4-158-429-31(1) 取扱説明書 カーオーディオ 14
6 Sony CDX GT430IP 取扱説明書 カーオーディオ 23
7 Sony Bluetooth 3-299-319-12 (1) 取扱説明書 カーオーディオ 22
8 Sony CDX 757MX 取扱説明書 カーオーディオ 38
9 Sony CDX GT54UIW 取扱説明書 カーオーディオ 55
10 Sony CDX-530RF 取扱説明書 カーオーディオ 6
11 Sony CD Walkman D-E775 取扱説明書 カーオーディオ 14
12 Sony CDX GT550UI 取扱説明書 カーオーディオ 82
13 Sony BLUETOOTHTM AUDIO SYSTEM MEX-BT5100 取扱説明書 カーオーディオ 109
14 Sony Bluetooth 4-158-430-31(2) 取扱説明書 カーオーディオ 192
15 Sony CDX-C910RDS 取扱説明書 カーオーディオ 6