ページ1に含まれる内容の要旨
Operating instructions
Heilbronn RCC 24
ページ2に含まれる内容の要旨
1 2 3 4 5 6 7 15 14 13 12 11 10 9 8 3 Heilbronn RCC 24 FRANÇAIS PORTUGUES ESPAGÑOL SVENSKA NEDERLAND ITALIANO ENGLISH
ページ3に含まれる内容の要旨
Contents Radio operation with RDS ........... 19 Tape operation.............................. 23 Short description.......................... 15 AF - Alternative Frequency ................... 19 Inserting a tape ..................................... 23 Important information .................. 17 REG - Regional ..................................... 19 Care of your audio equipment............... 23 What you need to know! ....................... 17 Selecting a station ...............................
ページ4に含まれる内容の要旨
Short description 1 Amplifier 2 Rocker switch 4 lo Seek tuning sensitivity On Off lo lit up in the display indicates normal Seek tuning seek tuning sensitivity (the system will Volume pick up strong stations only). up dx lit up in the display indicates high seek tuning sensitivity (the system will also pick up weaker stations). down in up in short steps short steps To change the seek tuning sensiti- vity: press lo. down When “CODE” lights up in the display, 5 FF read chapter “Anti-th
ページ5に含まれる内容の要旨
7 Display Extra function: < TA (Traffic Announcement) Coding - Read chapter “Anti-theft co- If TA is on, only traffic announcements ding” first. will be received. Waveband Buttons 1, 2, 3, 4 - To enter the four- TA on/off: press button. Station name/ digit code. frequency Memory bank = DSC (Direct Software Control) Preset button 9 TS (Travelstore) Use the DSC function to change a Tuning sensitivity To store the six most powerful nearby number of basic settings. See “DSC Alternative frequency sta
ページ6に含まれる内容の要旨
Important information Anti-theft coding Installation/connection The car radio comes standard with the code What you need to know! system deactivated. The code system can only be switched on Before starting to use your new car radio you If the anti-theft coding system is on while the and off, if the radio is connected to perma- should carefully read through the information power supply to the unit is interrupted (e.g. nent power. on “Traffic safety” and “Anti-theft coding”. theft, disconnecting t
ページ7に含まれる内容の要旨
The radio will operate again as soon as you Restart following interruption of If the radio is turned off before the waiting have entered the right code number. power supply period has elapsed, then the waiting period If you lose your radio passport and have (Code system switched on) restarts as soon as the radio is turned on forgotten your code number, you will not be again. • Switch on the set. able to restart the set after the power supply “CODE” will appear in the display. has been interrupte
ページ8に含まれる内容の要旨
Radio operation with RDS An ever increasing number of FM radio sta- “SEARCH” goes out as soon as the system Selecting a station tions broadcast addition information in paral- has found an alternative frequency or after FM radio stations in the range between lel to their normal program via the Radio Data the frequency band has been scanned com- 87.5 and 108 MHz can be received. System to make reception even more con- pletely. venient. Should the reception quality of the selected Automatic seek tu
ページ9に含まれる内容の要旨
Adjusting the seek tuning sensi- Note: Changing the memory bank (FM) tivity If you tune to a station which is already You can shift between the memory banks I, II stored, the corresponding preset button and Two basic levels can be selected for the seek and III to store and recall preset stations. the memory bank will flash in the display for tuning sensitivity. The selected memory bank is indicated in the ap-proximately 5 seconds. If “lo” is displayed, the radio will only tune to display. strong
ページ10に含まれる内容の要旨
Recalling stored stations Sampling stations briefly with Radio Scan You can recall any stored station by pressing the corresponding preset button. This function allow you to sample the subse- Use the FM or TS button to select the quent stations briefly for approximately 8 se- desired memory bank. conds each. For this purpose, press FM until the To active Scan: desired memory bank is indicated in the • press button 1 for approximately display. 1 second. Briefly press the desired preset button. Th
ページ11に含まれる内容の要旨
Reception of traffic announcements with RDS-EON Priority of traffic announcements Automatic seek tuning start Many FM broadcasters provide their service ON/OFF (During cassette operation) area with up-to-date traffic messages at re- gular intervals. “TA” lights up in the display, if the priority of If you leave the reception area of your traffic All traffic program stations transmit a special traffic announcements is on. To switch the program station while you are playing a cas- signal in parall
ページ12に含まれる内容の要旨
Tape operation DSC programming Care of your audio equipment This car radio offers direct software control Inserting a tape (DSC) to adjust a number of default settings We recommend you to use C-60/C-90 tapes Turn the set on. to your personal needs and store them. only in your car stereo. Protect your tapes by The following step describes all the default Insert a tape. storing them away from dirt and dust and do settings which can be changed. not expose them to excessive temperatures To activate
ページ13に含まれる内容の要旨
Appendix LOUD Loudness - To boost low Technical data bass frequencies. Amplifier: LOUD 0 - no boost Output power: 2 x 10 W RMS power ac- LOUD 6 - strong boost cording to DIN 45324/3.1 into 4 Ω BEEP Acknowledgement tone for FM: function keys to be hold down Sensitivity: 1.0 µV at 26 dB for more than 2 seconds. Ad- signal-to-noise ratio just volume between 0 and 9 Frequency (0 = OFF). response: 35 - 15 000 Hz (-3 dB) ARI (TA) To adjust the volume of traffic Cassette: announcements between 1 Frequ
ページ14に含まれる内容の要旨
Blaupunkt-Werke GmbH Bosch Gruppe 6/94 K7/VKD 3 D94 162 017 PM 14 Heilbronn RCC 24
