ページ1に含まれる内容の要旨
P-945WESP P-945WESP P-945WESP
P-945WESP P-945WESP
VOL
TUNE/
SKIP/
TRACK
VOL
AM/FM/MPX RADIO WITH DETACHABLE FRONT PANEL,
COMPACT DISC PLAYER, CD CHANGER CONTROLS AND
QUARTZ CLOCK
OWNER'S
MANUAL
Released 7-9-03.
128-6862A
Revision A: 8-22-03 Incorporated panel/display changes
1 of 16
ページ2に含まれる内容の要旨
INDEX Page Operating Instructions ................................................................ 3 - 9 Specifications ...............................................................................10 CD Changer Controls ...................................................................11 Setting the Clock ..........................................................................12 CD Player Error Codes.................................................................13 CD Changer Error Codes .
ページ3に含まれる内容の要旨
OPERATING INSTRUCTIONS 30 32 31 14 15 26 23 25 22 24 27 33 11 16 17 36 VOL TUNE/ 37 9 SKIP/ TRACK VOL 2 3,4,5,6,7 8,10 12 18 21,38 19,39 20,40 29,35 28,34 1 13 1 1 1 1 1 POWER ON/OFF BUTTON These buttons are also used in conjunction with the AUDIO SE- LECT (SEL) button 3 to adjust the bass, treble, balance, and Press this button to turn the unit on or off. If the unit is off and the fader levels as described in 4, 5, 6 and 7. ignition switch is "on", the time of day will be displayed. Also
ページ4に含まれる内容の要旨
ADJUST Volume buttons are used to select the desired beep appears on the display panel. Within 5 seconds of choosing the tone function. BEEP OFF indicates no beep tones. BEEP 2ND Balance mode, press the AUDIO ADJUST VOL or button indicates a tone will sound when a secondary function button is 2 to adjust the balance as desired. The balance position will be pressed, such as BAND/LOUD, and BEEP ALL indicates a tone shown on the display panel from BAL10L (full left) through BAL will sound whenev
ページ5に含まれる内容の要旨
AM band. The unit will stop at each preset station for 5 seconds 9 9 9 AUDIO MUTE (MUTE) 9 9 before continuing to the next pre-set station. During this time, This button is used to mute the volume from the system. By the preset station number (1-6) in the band will flash. Press the pressing the button, a flashing MUTE indication will appear on button again momentarily to stop Pre-Set Scan operation and the display panel and the volume will be muted. Pressing the remain on the selected frequen
ページ6に含まれる内容の要旨
station is now set into that preset memory position. The CAUTION: This unit is designed for play of standard 5" (12cm) station can now be recalled at any time by pressing that Compact Discs ONLY. Do not attempt to use 3" (8cm) button. CD-Singles in this unit, either with or without an adap- tor, as damage to the player and/or disc can occur. Such 4. Repeat the above procedure for the remaining pre-sets on damage will not be covered by the Warranty on this that band and for the other 3 bands on
ページ7に含まれる内容の要旨
cn cn cn DISC EJECT ( ) cn cn bu bu bu bu bu REPEAT PLAY SELECTOR (RPT) Disc play is stopped, the disc is ejected and the unit will change to radio operation by pressing this button. During disc play, press this button to repeat the play of the selected track (S--RPT will appear on the display panel). Play If the disc is not removed from the disc slot within 15 seconds of of the track will continue to repeat until the button is pressed being ejected, it will automatically be re-loaded into th
ページ8に含まれる内容の要旨
disc (the indication will remain on the display panel to show cq cq cq cq cq EQUALIZER SELECTOR (P.EQ) that a disc is still loaded in the unit). Press the button again to return to integral CD player mode and resume play of the disc The P.EQ button applies preset sound effects to the unit’s audio from the point at which it was stopped. output signal. The P.EQ button, when pressed, will activate one of the following operating modes: CLASSICS, POP M, JAZZ, FLAT,or DSP OFF. If the bass and trebl
ページ9に含まれる内容の要旨
dn dn dn RESET BUTTON dn dn A RESET button is located on the front of the chassis (front panel must be removed to access the button). The RESET circuitry is provided to DETACHING THE FRONT PANEL protect the microprocessor circuitry and should only be activated under the following circumstances as it will erase the time and pre-set memories: 1. Upon initial installation after all wiring is completed. 2. After the position of the frequency step switch on the bottom of the chassis has been changed.
ページ10に含まれる内容の要旨
SPECIFICATIONS Size: 7" W x 2" H x 6-5/8" D 178 mm x 50 mm x 168mm Operating Voltage: 12 volts DC, negative ground Output Power: 160 watts maximum (40 watts x 4 channels) Output Wiring: Floating-ground type designed for 4 speaker use. Front and rear channels CANNOT be combined (bridged) for use with 2 speakers. RCA low-level outputs (rear channels). Output Impedance: Compatible with 4 ohm speakers. Low-Level Output: 1.0 volt (1,000 mv.) Tuning Range: AM: 530 - 1,710 kHz. (10 kHz. step) FM: 87
ページ11に含まれる内容の要旨
CD CH CD CH CD CHA A ANGER CONTR NGER CONTR NGER CONTROL OL OLS S S dr dr dr dr dr TRACK SELECT (+ / -) CD CH CD CHA ANGER CONTR NGER CONTROL OLS S The Track Select functions are used to quickly access the Built into this radio are controls to operate an optional CD changer. beginning of a particular track. Each time the Forward Track Please check with your Rampage/Audiovox car stereo specialist Select (+ ) button is pressed, the next higher track number or call 1-800-645-4994 for recommendat
ページ12に含まれる内容の要旨
of the selected disc will continue ( DSN will disappear from the el el el DISC/TRACK SHUFFLE PLAY (SHF) el el display panel). The Disc Scan mode will also be canceled by When the SHF button is pressed, the SHF indication will appear activating the (Repeat Play or Shuffle Play functions). on the display panel and the tracks on the disc will be played in a random, shuffled order. The Track Select button dr will also se- du du du DISC/TRACK REPEAT PLAY (RPT) du du lect tracks in the shuffled o
ページ13に含まれる内容の要旨
CD PL CD PL CD PL CD PL CD PLA A A A AYER ERR YER ERR YER ERR YER ERR YER ERROR CODES OR CODES OR CODES OR CODES OR CODES If a problem should develop while operating the CD player, an error code (ER-1, ER-2, ER-3, etc.) may appear on the display panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the microprocessor control of the player. If an error code should appear, try ejecting and re-loading the disc into the player. While the disc is o
ページ14に含まれる内容の要旨
! Do not attempt to open the unit chassis. There are no user CARE AND MAINTENANCE serviceable parts or adjustments inside. The radio section of your new sound system does not require any ! When the vehicle warms up during cold weather or under damp maintenance. We recommend you keep this manual for conditions, moisture may condense on the lens of the disc reference on the many features found in this unit as well as how player. Should this occur, the player will not operate properly to set the
ページ15に含まれる内容の要旨
NOTES ON DISCS Attempting to use non-standard shape discs (e.g.; square, star, heart) may damage the unit. Be sure to use round-shape CDs only in this unit. NOTES ON CD-Rs (Recordable CDs)/CD-RWs (Rewriteable CDs): 1. Be sure to use discs with the following marks only for play in this unit: . 2. The unit cannot play a CD-R or CD-RW that is not finalized. (Please refer to the manual of your CD-R/CD-RW software for more information on the finalization process.) 3. Depending on the recording
ページ16に含まれる内容の要旨
12 / 24 MONTH LIMITED WARRANTY Applies to automotive radios, radio/tape players, radio/CD players, CD changers, power amplifiers, equalizers and accessories. AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned
