ページ1に含まれる内容の要旨
ge.com
Safety Information . . . . . . . . . . 3
Owner’s Manual
and Installation
Operating/Care and
Instructions
Cleaning Instructions
Charcoal Filters . . . . . . . . . . . . . .5 JV535
Grease Filters . . . . . . . . . . . . . . . .4
JV536
Hood Lights . . . . . . . . . . . . . . . .5
JV565
Hood Surfaces . . . . . . . . . . . . . . .5
JV566
Stainless Steel Surfaces . . . . . . . .5
JV635
Vent Controls . . . . . . . . . . . . . . .4
JV636
Installation Instructions . . .6–14 JV665
JV666
Consumer S
ページ2に含まれる内容の要旨
GE & You, A Service Partnership. IMPORTANT! Fill out the Consumer Product Registration Card. Two easy ways to register your appliance! Through the internet at ge.com Complete and mail the enclosed Product Registration Card FOR YOUR RECORDS Write the model and serial numbers here: # # You can find them on a label on the back wall of the hood. Staple sales slip or cancelled check here. Proof of the original purchase date is needed to obtain service under the warranty. READ THIS MANUAL Inside
ページ3に含まれる内容の要旨
Safety Instructions Operating Instructions Installation Instructions Consumer Support IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. SAFETY PRECAUTIONS WARNING – TO REDUCE THE RISK OF FIRE, WARNING – TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE A RANGE TOP GREASE FIRE: THE FOLLOWING: A. Never leave surface units unattended at high A. Use this unit only in the manner intended settings. Boilovers cause smoking and greasy by the manufacturer. If you have qu
ページ4に含まれる内容の要旨
Using the hood controls. Throughout this manual, features and appearance may vary from your model. Your model will have one of the above type of controls. FAN Control LIGHT Control Turn or press (according to your model) the FAN Turn or press (according to your model) the speed control to LO, MED, HI or BOOST, as needed. LIGHT control to BRIGHT for bright light while cooking. Turn or press to NITE for use as a night Continuous use of the fan system while cooking light. helps keep the kitchen co
ページ5に含まれる内容の要旨
Safety Instructions Operating Instructions Installation Instructions Consumer Support Charcoal Filters (on some models) If the model is not The charcoal filters The charcoal filters vented to the outside, the should be replaced when cannot be cleaned. They air will be recirculated they are noticeably dirty must be replaced. through disposable or discolored (usually For 30″ hood models, order charcoal filters that help after 6 to 12 months, Kit no. WB02X10707. remove smoke and depending on hood
ページ6に含まれる内容の要旨
Range Hood Installation Models JV535 JV635 JV536 JV636 Instructions JV565 JV665 JV566 JV666 Questions? Call 1.800.GE.CARES or visit our Website at: ge.com DUCTWORK REQUIREMENTS BEFORE YOU BEGIN NOTE: Read the ductwork sections only if you do not Read these instructions completely and carefully. have existing ductwork. If you have existing ductwork, skip to the “Damage” section and proceed. • IMPORTANT – Save these instructions for local inspector’s use. The venting system must exhaust to th
ページ7に含まれる内容の要旨
Installation Instructions Follow the guidelines for proper duct sizing in the ducting charts. DUCTING CHART—JV5 Series Models Equivalent Length in Feet 0 25 50 75 100 125 150 250 • • • 200 • • 7″ Round • • 150 • • 1 3 ⁄4″ x 10″ • Rectangular 100 1 3 ⁄4″ x 10″ Rectangular Transition to 6″ Round = 4.5 ft. 7″ Round 90° Elbow = 8 ft. 7″ Roof Cap = 30 ft. DUCTING CHART—JV6 Series Models Equivalent Length in Feet 0 25 50 75 100 125 150 400 • 350 • 7″ Round • • • 300 • • • 250 • 1 3 ⁄4″ x 10″ • Rectang
ページ8に含まれる内容の要旨
Installation Instructions WORKSHEET—CALCULATE TOTAL EQUIVALENT DUCTWORK LENGTH DUCT EQUIVALENT NUMBER DUCT EQUIVALENT NUMBER PIECES LENGTH x USED = TOTAL PIECES LENGTH x USED = TOTAL 1 3 ⁄4″ x 10″ 1 Ft. x ( ) = Ft. 6″ Round 34 Ft. x ( ) = Ft. Rect., wall cap (6 ft. w/o straight with damper) x ( ) = Ft. damper 7″ Round, 1 Ft. x ( ) = Ft. straight 6″ Round 30 Ft. x ( ) = Ft. roof cap 6″ Round, 1 Ft. x ( ) = Ft. straight 6″ Round 5.5 Ft. x ( ) = Ft. to 1
ページ9に含まれる内容の要旨
Installation Instructions DAMAGE—SHIPMENT/INSTALLATION TOOLS YOU WILL NEED • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or Flat blade and Phillips Pencil replacement is the responsibility of the customer. screwdrivers Duct tape • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and instal
ページ10に含まれる内容の要旨
Installation Instructions 1 Outside rear exhaust CHOOSE VENT OPTION C 1 (Horizontal duct—3 ⁄4″ x 10″ The outside vent exhaust option that your installation Rectangular) requires will determine the hood knockouts that you will use. If the hood is to be installed in a recirculating, non- vented ductless manner, do not knock out any vent openings in the hood. Only an electrical access hole will be knocked out of the hood. NOTE: Only JV5 Series models may be recirculated. We do not recommend the r
ページ11に含まれる内容の要旨
Installation Instructions 2 REMOVE EXHAUST ADAPTOR 5 REMOVE OTHER EXHAUST ADAPTOR 1 Remove the 7″ round exhaust adaptor from the top of Remove the 3 ⁄4″ x 10″ rectangular exhaust adaptor the hood. Set it aside along with its mounting screws. from inside the hood. Set it aside along with its mounting screws and parts bag. Depending on the model, the exhaust adaptor will be located on the left or right side. 7″ round exhaust adaptor 1 1 3 ⁄4″ x 10″ 3 ⁄4″ x 10″ rectangular rectangular 3 REMOVE FI
ページ12に含まれる内容の要旨
Installation Instructions 1 10 8 FOR 3 ⁄4″ X 10″ RECTANGULAR REMOVE DUCT KNOCKOUT(S) If recirculating, non-vented ductless (optional for DUCTED DISCHARGE JV5 Series models only), see note below and skip to INSTALLATIONS ONLY: Step 12 D and proceed. We do not recommend the Attach exhaust adaptor/damper over knockout recirculated configuration for JV6 Series models. opening with two exhaust adaptor screws. Make sure Using a flat blade screwdriver, remove the appropriate damper pivot is nearest t
ページ13に含まれる内容の要旨
Installation Instructions 12 D.Recirculating (non-vented ductless— MARK HOLES Available on JV5 Series models only) Select the vent option that your installation will require and proceed to that section: • Use the hood as a template and mark the locations on the cabinet for the electrical wiring and keyhole A.Outside top exhaust screw slots. 1 (Vertical duct—3 ⁄4″ x 10″ Rectangular) • Since the hood is to be recirculated (not to be vented outside), do not cut out any vent openings in the wall •
ページ14に含まれる内容の要旨
Installation Instructions 22 CONNECT WIRING 18 SECURE HOOD Connect house black to hood black wire, house Slide the hood back against the wall. Tighten white to hood white wire, and house ground under the mounting screws. Be sure the screw heads green ground screw. Securely tighten the strain are in the narrow neck of the keyhole slot. relief clamp onto the house wiring. Green ground screw Mounting screw (4) Keyhole (4) NOTE: DO NOT PUSH ON FAN BLADE. Pushing 23 REPLACE WIRING COVER on the blade
ページ15に含まれる内容の要旨
Safety Instructions Operating Instructions Installation Instructions Consumer Support GE Range Hood Warranty. All warranty service provided by our Factory Service Centers ® or an authorized Customer Care technician. To schedule service on-line, 24 hours a day, visit us at ge.com or call 800.GE.CARES (800.432.2737). Please have serial number and model number available when calling for service. For The Period Of: GE Will Replace: One Year Any part of the range hood which fails due to a defect in
ページ16に含まれる内容の要旨
Consumer Support. GE Appliances Website ge.com Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, ™ order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts ” your questions, and so much more... Schedule Service ge.com Expert GE repair service is only one step away from your door. Get on-line and schedul
