ページ1に含まれる内容の要旨
VIDEO CASSETTE PLAYER
-
HR P41A
OPERATE STANDBY
INTELLIGENT
NTSC
SP/LP/EP PICTURE
ON PAL TV
INTELLIGENT
NTSC 3.58/4.43 NTSC3.58
PICTURE LP/EP PAL NTSC
VIDEO CASSETTE RECORDING & PLAYBACK
NTSC4.43
PLAYER
HR-P41A
PAL NTSC
INSTRUCTIONS
PU30425-1844
ENGLISH
ページ2に含まれる内容の要旨
Table of contents Precautions Thank you for purchasing this JVC video cassette player. To The rating plate and the safety caution are on the rear of the unit. ensure optimum performance of this unit, please read this instruction manual thoroughly. WARNING: DANGEROUS VOLTAGE IN- SIDE Precautions ........................................................................... 2 WARNING: TO PREVENT FIRE OR SHOCK Controls and terminals .......................................................... 3 Wireless
ページ3に含まれる内容の要旨
Controls and terminals Front panel 1 24 3 5 OPERATE STANDBY INTELLIGENT NTSC PICTURE SP/LP/EP ON PAL TV NTSC 3.58/4.43 INTELLIGENT NTSC3.58 PICTURE LP/EP PAL NTSC VIDEO CASSETTE RECORDING & PLAYBACK NTSC4.43 PLAYER HR-P41A $" # !9876 1 OPERATE button 0 Remote sensor window To turn the power on and off (standby mode). For remote control operation. 2 Cassette loading slot ! Colour System Output switch Load the video cassette here. Select to watch an NTSC tape. 3 Rewind 1 button @ Mode indicators
ページ4に含まれる内容の要旨
Wireless remote control When using the remote control for operation of the video cassette player, make sure that it is pointed at the remote sensor window. OPERATE STANDBY INTELLIGENT NTSC SP/LP/EP ON PAL TV PICTURE INTELLIGENT You can also use the player’s remote control to operate a JVC NTSC 3.58/4.43 NTSC3.58 VIDEO CASSETTE PICTURE LP/EP PAL NTSC RECORDING & PLAYBACK NTSC4.43 PLAYER HR-P41A television. 1 Transmitting window 1 2 TV channel –/+ buttons 3 TV VOLUME –/+ buttons TV - TVCH +
ページ5に含まれる内容の要旨
Connections Make sure that the power to the video cassette player and TV is off before making the following connections. Connection A 10- 40 32 RF OUT IN OUT K AUDIO G ANT. IN VIDEO 1- Connection B Note: If you put a TV set directly on this VCP or install it too close to a TV set, noise may occur. If this noise occurs, separate the VCP and the TV set. Connection A (basic) Connection B In order to use the video cassette player it must be connected For connection of a TV that has VIDEO/AUDIO IN/OU
ページ6に含まれる内容の要旨
40 32 Setting the video channel The video cassette To watch videos on your TV, it must be set to the same UHF Inserting a cassette channel as the video cassette player. This channel is used as the video channel. This video cassette player has been preset to UHF channel 36. Note: OPERATE STANDBY • When you have connected the VIDEO/AUDIO OUT termi- NTSC INTELLIGENT SP/LP/EP ON PAL TV PICTURE NTSC 3.58/4.43 INTELLIGENT NTSC3.58 PICTURE LP/EP PAL NTSC VIDEO CASSETTE RECORDING & PLAYBACK NTSC4.43 PLA
ページ7に含まれる内容の要旨
Playback NTSC, PAL and MESECAM video tapes can be played back on NTSC Playback on PAL TV this video cassette player. Refer to the “Colour system output mode selection” section for details. • The vertical size of the playback picture will shrink and some picture “noise” may appear on the screen. • The playback picture may roll. In this case adjust the picture Before proceeding: with the TV’s vertical hold knob (with some TV’s this adjust- ment may not be possible). • The colour of the playback pi
ページ8に含まれる内容の要旨
Playback features Slow motion playback Intelligent picture Slow motion playback is 1/6 of the normal playback speed. The Use this feature to get a better picture when viewing tapes with sound will be cut during slow motion playback. noise such as rental tapes. (SP mode only) During playback: Press the INTELLIGENT PICTURE button. 1 The INTELLIGENT PICTURE indicator will light. Press the Pause 8 button for 2 seconds. 1 7 Press the INTELLIGENT PICTURE button to cancel this feature. 7 Press the Play
ページ9に含まれる内容の要旨
Recording Editing Use the following procedure to record TV programmes on a Editing To/From Another Recorder blank video tape. Player Before proceeding: • To record TV programmes, the video cassette player must 10- 40 32 be connected to the TV as shown in connection B of the RF OUT IN OUT K AUDIO G “Connections” section. ANT. IN VIDEO 1- • Turn on the power of the TV and video cassette player. • Make sure that the video cassette’s safety tab is intact. If it has been removed, cover the hole with
ページ10に含まれる内容の要旨
Troubleshooting Specifications Format................................ VHS Standard Problem Check point Video recording system ..... Rotary, slant azimuth two-head helical scan system No power Is the power cord plugged Rotary heads...................... 2 video heads in? RF output ........................... System G/K type modulation Is the power turned on? UHF ch 32 – 40 adjustable (preset Tape cannot be ejected Was the video cassette ch 36) player’s ¤ button pressed? Recording (line input) ...
ページ11に含まれる内容の要旨
MEMO 11
