ページ1に含まれる内容の要旨
®
ELECTRONICS CORP.
VOH560PKG Drop Down Video Monitor
and Video Cassette Player System
Installation and Operation Manual
ページ2に含まれる内容の要旨
Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the motor vehicle. Please note that the state of Rhode Island forbids the installation of such a device in a motor vehicle.
ページ3に含まれる内容の要旨
MATERIALS INCLUDED IN THIS PACKAGE: 1)VOH560 Video Monitor with out TV Tuner (1 pc) 2)VCP Harness (P/N 112C3035) (1 pc) 3)12 Pin Power / Signal harness (P/N 112B2821) (1 pc) 4)2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc) 5)Hardware Package for VOH560 #4 x 3/8” Screws (12 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 6)Remote Control (P/N 136C1957)(1pc) 7)Left Protective Cover for External A / V Inputs (P/N 102B3596) (1pc) 8)Right Protective Cover for Headpho
ページ4に含まれる内容の要旨
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, RF nd Modulator/external amp, remote headphone, 2 VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire harn
ページ5に含まれる内容の要旨
VEHICLE PREPARATION: 1) Locate a constant power source (+12v at all times) and an accessory power source (+12v when key is in the acc. and run positions, and 0v when key is off). Generally, these wires can be found at the ignition switch or fusebox. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the vehicl
ページ6に含まれる内容の要旨
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini console installation. If the video monitor is to be installed with a custom full sized overhead console, refer to page 3. If the video monitor is to be installed in a vehicle with the mini console (P/N 102D3595), this console may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the video monitor is mounted directly to the overhead crossmember in the roof usin
ページ7に含まれる内容の要旨
MOUNTING THE MINI CONSOLE Roof Roof support Headliner 5"x9"x3/4" Plywood Block or Optional VOHBKT (4) #8x1" self drilling screws (not supplied) Mini-Console Video unit (4) #8 Flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5-
ページ8に含まれる内容の要旨
VOH560 Note: cables exiting the pod should be routed as sho w n. Power Harness Red: +12 V DC Item # 4 M ini-Din Connectors 4 (Accessory Cir.) cho ke Black: Ground Optional Hard Wired FM Modulator Output 21 RC A-Female 12 V DC Powe r an d Groun d Left Inpu t Am/Fm LE FT Antenna FM TO WHITE Pa tch Co rd Modulator FACTORY RIG HT 1070610 RED RADIO Dash Radio Rig ht *Refer to Instructions with the RF Inpu t M od ulato r K it fo r fu rthe r d etails. RC A-Female To Secondary AV Monito
ページ9に含まれる内容の要旨
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, b
ページ10に含まれる内容の要旨
Negative Switched Dome lighting Red / black - Lamp on To 12 pin Black / red - Lamp common connector Purple / brown - Lamp Auto on Monitor To constant +12vdc Factory Dome light circuit To constant +12vdc Factory Door ajar switch or Body Control computer Troubleshooting: Remedy: Symptom: -Verify +12 VDC on Red wire at 2 pin Power Harness behind video moni- No power at Video Monitor tor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness -Ver
ページ11に含まれる内容の要旨
4 1 5 2 6 3A 7 8 9 10 3B Front Panel 1. Infrared Transmitter – Used to transmit audio to wireless headphones. 2. Power Button – (Bright red when system is On, dim when OFF). 3A. Forward Remote Sensor Eye – Allows the remote control to operate the VOH560 OSD (On Screen Display), control volume to wired headphone jacks (and optional external speakers), and to control the Video Cassette Player and other accessories. 3B. Side Remote Control Eye – Allows the remote control operate th
ページ12に含まれる内容の要旨
VCP756 FRONT AND BACK VIEW VID E O AU D IO L 8 AU D IO R 9 POWER STOP/EJECT REW PLAY F F REPEAT 1 5 7 234 6 10 1. Dust Cover – Protects VCP from dust and abuse access. 2. Power Button – (Bright red when system is On, dim when Off). 3. Stop / Eject Button – Used to stop the tape, and press it once more to eject the tape. 4. (Fast) Rew Button : – Press Fast Rewind once in playback mode, the VCP enters the reverse picture search mode and the tape will rewind
ページ13に含まれる内容の要旨
REMOTE CONTROL OPERATION 1 5 BATTERY INSTALLATION 4 POWER VIDEO REPLAY or GAME Before attempting to operate your Remote Control, 3 2 + PICTURE install the batteries as described below. SELECT WIRED HEADPHONE VOLUME CONTROL 1) Turn the Remote Control face down. Press REW FWD 8 6 down on the ridged area of the battery cover and slide it off. STOP PLAY 9 7 2) Install two “AAA” batteries as shown. Make sure that proper polarity (+ or -) is observed. 3) Slide the cover back
ページ14に含まれる内容の要旨
Remote Controlled VCP Functions 5. REPLY BUTTON Pressing this button will rewind tape and immediately begin playback when the tape is fully rewound. 6. “REW” REWIND BUTTON If this button is pushed while the tape is stopped, the tape will rewind. If this button is pushed while the tape is playing, the VCP will go into rewind search mode. For more information, see page 10. 7. PLAY BUTTON Press this button to activate play mode while a tape is loaded into the VCP
ページ15に含まれる内容の要旨
Remote Sensor The VOH560 incorporates an infrared sensor which relays signals from the remote control to allow the VOH560 and VCP to be controlled simply by pointing its remote control at the remote sensor eye. This provides control of auxiliary equipment such as an Audiovox DVD. The infrared sensor can reply signals to auxiliary source that is connecting to monitor din connector #2, such as a DVD player. In this case you must use the remote control supplied with the DVD player. Remote Sensor Ey
ページ16に含まれる内容の要旨
Wired FM Modulator Your video system may be equipped with an RF modulator, that allows you to listen to the VOH560’s audio signal by tuning your vehicle’s radio to the selected frequency, (88.7 or 89.1 - check with your installer) and turning on the remote mounted RF modulator switch. (In most cases this toggle switch will be located underneath the driver’s side of the dash, check with your installer for the exact location.) Whenever the RF modulator is on, broadcast radio reception will be poor
ページ17に含まれる内容の要旨
Warnings F Do not use any solvents or cleaning materials when cleaning the video system. F Do not use any abrasive cleaners, they may scratch the screen. Use only a lightly dampened lint free cloth to wipe the screen if it is dirty. F Lock the LCD screen in the fully closed position when not in use. F Before putting on headphones always adjust the volume setting to the lowest position. F Remember to leave the dome light switch in the off or auto positions when the vehicle is unattende
ページ18に含まれる内容の要旨
For Custom er Service Visit O ur W ebsite At WWW.audiovox.com Product Information, Photos, FAQ ’s O wner’s M anuals © Copyright 2001 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788 128-6065
