ページ1に含まれる内容の要旨
HIGH SPEED BURNISHER
MODELS:
LB2000I LB2000IAUB2000F LB2000
1009020010090210 1009062010090190
Operating Instructions (ENG)
86309600-B
01/29/09
ページ2に含まれる内容の要旨
MACHINE DATA LOG/OVERVIEW Model: Date of Purchase: Serial Number: Sales Representative: Address: Phone Number: OVERVIEW The High Speed Burnisher is a mains powered, portable floor burnisher intended for commercial use. The appliance can be fitted with a variety of pads to perform various floor care functions. The appliance employs active dust control, and automatically adjusted pad pressure. 86309600 (2000) BURNISHER 10/08/08
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Machine Data Log/Overview................................2 Table of Contents.................................................3 HOW TO USE THIS MANUAL How to use this Manual........................................1-1 SAFETY Important Safety Instructions ...............................2-1 Hazard Intensity Level..........................................2-2 Grounding Instructions.........................................2-3 OPERATION Technical Specifications
ページ4に含まれる内容の要旨
HOW TO USE THIS MANUAL This manual contains the following sections: The OPERATIONS section is to familiarize the operator with the operation and function of the - HOW TO USE THIS MANUAL machine. - SAFETY - OPERATIONS The MAINTENANCE section contains preventive - MAINTENANCE maintenance to keep the machine and its - PARTS LIST components in good working condition. They are listed in this general order: The HOW TO USE THIS MANUAL section will tell you how to find important inform
ページ5に含まれる内容の要旨
SAFETY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To r educe the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments. If the machine is not working properly, has been dropped, damaged, left outdoors
ページ6に含まれる内容の要旨
SAFETY The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices, which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices, which could result in minor personal injury
ページ7に含まれる内容の要旨
SAFETY GROUNDING INSTUCTIONS-120V Grounding Pin THIS PRODUCT IS FOR COMMERCIAL USE GROUNDING CONNECTION ONLY. USING AN ADAPTOR ELECTRICAL: Grounded Outlet In the USA this machine operates on a one 15 Metal Screw FIGURE A amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or Adaptor below those indicated on the data label will cause Tab for Grounding Grounded FIGURE B Screw Outlet Box seriou
ページ8に含まれる内容の要旨
SAFETY GROUNDING INSTRUCTIONS-230V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENSION CORDS: If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length. GROUNDING INSTRUCTION
ページ9に含まれる内容の要旨
SAFETY SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement. WARNING LABEL P/N 86219740 PRV NO. 500194 86309600 (2000) BURNISHER 10/08/08 2-5
ページ10に含まれる内容の要旨
TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Construction Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel self adjusting handle with die cast aluminum handle housing. Motor 1.5 hp Transmission Direct drive from motor shaft. Pad speed 2000 rpm Electrical system: LB2000I, LB2000IA 230 volts, 50Hz LB2000, UB2000F 115 volts, 60Hz 75’ [22.9 m] Cable Switches Dual levers with safety lock. Pad Holder ∅20” [50.8 cm] flexible disc
ページ11に含まれる内容の要旨
OPERATION HANDLE ASSEMBLY 2 3 1 HANDLE MOUNT BRACKET DECK ASSEMBLY HANDLE INSTALLATION The machine is shipped with handle unassembled. 4. Slide Bolt (item 3) through, washers (item 2), Handle Mount Brackets and Handle Assembly as Follow these steps for installation: shown. Tighten bolt (item 3) and nut (item 1) until the handle cannot twist in the mount bracket (45- 1. Remove handle and deck assembly from 50 foot pounds). carton. 5. Check handle for movement up and dow
ページ12に含まれる内容の要旨
OPERATION 6. To stop the machine, release the switch CONTROLS levers. 1. Safety Lock – Prevents unintended operation 7. Do not let machine rest on pad. When of the machine. finished with the machine, return handle to the storage position. 2. Switch Levers – Turns machine on/off. NOTE: The machine is equipped with a circuit 1 breaker to protect the motor in the event an overload condition occurs. The circuit breaker is located on the handle. Push the reset but
ページ13に含まれる内容の要旨
MAINTENANCE MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Tripped circuit breaker Reset Circuit breaker tripped in Check and reset building. Fuse in motor is blown Replace CAUTION: To reduce the risk of electrical shock, unplug the machine before opening fuse holder. Machine will not run Fuse will only open under extreme conditions. Investigate cause before replacing. Power switch failure Test switch for continuity and replace if necessary. Faulty power cord Replace
ページ14に含まれる内容の要旨
MAINTENANCE SERVICE SCHEDULE MAINTENANCE DAILY MONTHLY Check pad wear to prevent buildup of chemicals * Check pad driver system for damage * Check handles, switches, and knobs for damage * Store with pad off the floor * Check all bearings for noise * Check skirt/bumpers for damage and replace as necessary * Check overall performance of machine * 4-2 86309600 (2000) BURNISHER 10/08/08
ページ15に含まれる内容の要旨
NOTES: 4-3 86309600 (2000) BURNISHER 10/08/08
ページ16に含まれる内容の要旨
DECK 1 2 3 5 6A-B 4 7 8 9 11 10 16 12 13 14 15 5-1 86309600 (2000) BURNISHER 10/08/08
ページ17に含まれる内容の要旨
DECK SERIAL NO. REF PART NO. PRV NO. QTY DESCRIPTION NOTES: FROM 1 86216280 140449 4 BUMPER, RUBBER 2 86217520 27918 1 COVER, FILTER BAG 3 86001390 140441 1 BAG, DUST (PACKAGE OF 10 BAGS) 4 86223430 67463 1 RETAINER, CORD 5 86276810 70738 2 SCR, M5 X .8MM X 10 MM PPHMS BLK LB2000, 6A 86217640 29244BLU 1 DECK, 20 IN BURNISHER, BLUE LB2000I, LB2000IA 6B 86289010 29244GRY 1 DECK, 20 IN BURNISHER, GRY UB2000UF 7 86216270 140423 1 BUMPER, EXTRUSION 8 86137
ページ18に含まれる内容の要旨
ELECTRICAL 1 2 3 4 15 14 A-B 5 6 7 13 A-C 12 11 10 9 8 5-3 86309600 (2000) BURNISHER 10/08/08
ページ19に含まれる内容の要旨
ELECTRICAL SERIAL NO. REF PART NO. PRV NO. QTY DESCRIPTION NOTES: FROM 1 86136780 70801 2 SCR, M 3.5 X 40 PHTF TYPE B 2 86137290 87057 2 WASHER, M4 SHAKEPROOF 3 86224750 73993 1 SPRING, COMP, .48OD X .91L SWITCH, 25A SPST 125-250V 4 86007110 72123 2 SNAP 5 86288450 70689 1 SCR, M4.8 X 10 HHTF TYPE B WASHER, M5 SHAKEPROOF 6 86137330 87208 1 PLTD 7 86198450 20005 1 CLAMP, 5/16 NYLON 8 86227300 730021 1 SPACER, POLISHER HANDLE 9 86224930 730012 1 STRAIN RELIEF, 14
ページ20に含まれる内容の要旨
HANDLE-LOWER 16 17 14 19 17 15 18 10 24 7 8 23 6 9 1 2 5 11 3 4 13 12 22 21 25 20 8 5-5 86309600 (2000) BURNISHER 10/08/08
