ページ1に含まれる内容の要旨
®
I
SS
HIGH DEFINITION
COMPONENT SYSTEMS
PCH-14X
PCH-314 / PCH-414
PCH-514 / PCH-614
INSTALLATION & OPERATION
®®
ページ2に含まれる内容の要旨
Dear Customer, Congratulations on your purchase of America’s finest brand of car audio compo- nents. At Rockford Fosgate we are committed to musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures we have created a wide range of products that reproduce music with all the clarity and richness you deserve. For maximum performance we recommend you have your new Rockford Fosgate product i
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Package Contents .................................................................................... 1 Introduction ............................................................................................ 1 Technical Design Features ...................................................................... 2 Installation Considerations ...................................................................... 4 Tools Needed .........................................................
ページ4に含まれる内容の要旨
PACKAGE CONTENTS PCH-14x PCH-314 (1) Installation & Operation Manual (1) Installation & Operation Manual (2) 3/4" Tweeter (2) 3/4" Tweeter (2) TX-4186 Crossover (2) 3" Midrange Speaker (2) Surface Mount Base (2) 4x6 Mounting Plate (2) Surface Mount Cup (2) TX-4186 Crossover (2) Flush Mount Base (2) 100µ f Capacitor (2) Flush Mount Cup (2) Surface Mount Base (2) Surface Mount Cup PCH-414/PCH-514 or PCH-614 (2) Flush Mount Base (1) Installation & Operation Manual (2) Flush Mount Cup (2) 3/4" Tweet
ページ5に含まれる内容の要旨
TECHNICAL DESIGN FEATURES Midrange Features PVA Treated Cone The lightweight paper cones are treated with PVA (PolyVinyl Acetate) for environmental stability and increased rigidity. This treatment promotes smooth midrange performance and low frequency extension free of distortion. THE RESULT: Strong and lightweight high performance cones. Vented Pole Piece The vented pole piece by design, ensures proper ventilation to cool the voice coil and maintains lower operating temperatures. This incre
ページ6に含まれる内容の要旨
Tweeter Features Neodymium Magnets The high ionic compound of neodymium enables a smaller tweeter magnet assembly to be used as opposed to the much larger ferrite magnets that are commonly used in speaker manufacturing. THE RESULT: An efficient magnet which allows smaller tweeter construction. Magnetic Fluid Cooling Magnetic fluid is a synthetic liquid consisting of microscopic magnetic particles. The fluid has four times the thermal conductivity as air which makes it an ideal cooling agent
ページ7に含まれる内容の要旨
Optical Compression Circuit The supplied passive crossovers utilize an optical compression circuit for tweeter protection. This protection circuit absorbs the destructive signal caused when the amplifier's output is clipped. This greatly increases the power handling capability and the reliability of the tweeter. THE RESULT: Increased tweeter reliability under harsh conditions. Passive Filter Bypass The TX-4186 utilizes an extra screw terminal on the crossover housing which allows the tweet
ページ8に含まれる内容の要旨
® ® I N S T A • Place the speakers where they have L L A T I O a direct path to the listening area. N • When using the Punch Splits, there 2" or less are two options for speaker place- ment between the midrange and tweeter. For the best integration be- tween the midrange and tweeter, the tweeter should be placed less than 2" from the midrange. (Figure 1) Figure 1 • If you cannot place the tweeter less than 2" from the midrange, then place the tweeter more than 7" from the midrange. Placing the t
ページ9に含まれる内容の要旨
® ® I N S T A L L A Punch Splits speakers with minimum path length differences will T I O N ensure the best staging and imaging possible from your audio system. INSTALLATION The mounting of the Punch Splits speakers and crossovers is just as important as choosing the location for the speakers. Improper installation will degrade the sound quality and reduce the reliability of the Punch Splits speakers. To maximize the performance of your speakers, the following criteria should be considered. • Af
ページ10に含まれる内容の要旨
® ® I N S T A L L A T I 5. Place the mounting ring over the hole. O N 6. Attach the wires and be sure to observe the proper speaker polarity. Keep the speaker wires away from sharp and moving objects. 7. Place the speaker into the hole and screw the speaker into place. Be careful not to bend the speaker frame during this step. 8. Press the speaker grille into the mounting ring. Flush Mounting the Tweeter 1. Cut a 1-1/4" mounting hole. 2. Route the wires through the mounting hole. 3. Attach the w
ページ11に含まれる内容の要旨
® ® I N S T A L L A Mounting the Punch Splits Plates T I O N 1. Cut the proper size hole for the midrange/woofer and tweeter. The midrange/woofer hole should be slightly larger than the mounting plate woofer hole. 2. Place the mounting plate over the mounting holes and mark the location of the screw mounting holes. 3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit. 4. Mount the speaker plate. Be careful not to bend the mounting plate during this step. 5. Route the wires
ページ12に含まれる内容の要旨
® ® I N S T A L Wiring the PCH-314 L A T I O N ®® ® ACTIVE TWEETER PROTECTION TX-4186 (Rear View) PCH-14 – + + – + Dot indicates “+” Terminal Input Protection Striped Wire (Rear View) PCH-34 Dot indicates “+” Terminal Output from – + 100µ f Amplifier capacitor – 9 –
ページ13に含まれる内容の要旨
® ® I N S T A Wiring the TX-4186 L L A T I O (Crossover/Tweeter Protection) N TWEETER CROSSOVER PROTECTION ® + – Input Tweeter Input Output Protection + OUTPUT + FROM – AMPLIFIER – • Striped Wire indicates “+” terminal of tweeter Wiring the TX-4186 (Tweeter Protection Only) TWEETER PROTECTION ® Input Tweeter Input Output Protection + OUTPUT – FROM + AMPLIFIER – • Striped Wire indicates “+” terminal of tweeter • WARNING: Use an external high-pass filter of at least 6kHz @ 18dB when configurin
ページ14に含まれる内容の要旨
®® ACTIVE TWEETER PROTECTION TX-4186 I ® ® N S T A L L Tweeter Level Matching A T I O N (Bottom view of PCH-142x/TX-4186 Cut jumper wire for –3dB • Factory set tweeter level is 0dB • Cut jumper wire on bottom of crossover to reduce tweeter level by –3dB Horizontal Logo Mounting ®® ® ACTIVE TWEETER PROTECTION TX-4186 ® • Configure logo into desired position and snap into place Vertical Logo Mounting ® ® • Configure logo into desired position and snap into place – 11 – ®® ACTIVE TWEETER PROTECTIO
ページ15に含まれる内容の要旨
TROUBLE-S H O O T TROUBLESHOOTING I N G Symptom Diagnosis Remedy No sound from Check and repair or Wires between amplifier, speakers replace wiring as needed. crossover and speakers not connected properly. Check system with known Amplifier has no output. working amplifier and re- pair or replace as needed. Check for shorts in the Speaker wires are wiring with a volt/ohm shorted to each other or meter and repair or to the chassis of the replaced wires as needed. vehicle. Check system with known S
ページ16に含まれる内容の要旨
Ω Ω Ω Ω Ω – 13 – SPECIFICATIONS Model PCH-14 PCH-34 PCH-44 PCH-54 PCH-64 Freq. Response 6.5kHz-20kHz 225Hz-10kHz 100Hz-6kHz 50Hz-6kHz 45Hz-6kHz Power Handling (RMS) 50 Watts* 50 Watts 50 Watts 50 Watts 50 Watts Nom. Imp. 4 4 4 4 4 Sensitivity (1W/1M) 88dB 85dB 85dB 86dB 89dB Nom. Diameter 3/4" 3.5" 4" 5.25" 6.5" Cutout Diameter 1-1/4" 3-3/16" 3-13/16" 4-7/8" 5-11/16" Mounting Depth 29/32" 1-1/4" 1-9/16" 2-1/2" 2-3/4" FS (Hz) 2800Hz 225Hz 100Hz 50Hz 45Hz QTS 1.00 1.50 0.80 0.43 0.40 QMS 1.30 3.10
ページ17に含まれる内容の要旨
LIMITED WARRANTY INFORMATION Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: • Length of Warranty 1 year on speakers 30 days on speaker B-stock (receipt required) 3 years on electronics 90 days on electronic B-stock (receipt required) 2 years on source units • What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions. Produc
ページ18に含まれる内容の要旨
I NFORMATION – 15 – INTERNATIONAL
ページ19に含まれる内容の要旨
ESPAÑOL Asegurese de leer las instrucciones antes de instalar estos productos. INTRODUCCIÓN En los vehiculos de hoy en dia, premia el espacio para todo. Muchas veces, el espacio que los diseñadores de coches dedican al equipo de música es un requerimiento posterior al diseño. Rockford Fosgate sabe que la gente que quiere equipos de música en sus vehiculos, debe pelear con este problema cotidiano. Nuestra solución es los sistema de componentes de Alta definicíon Punch Split. Los altavoces Punch S
ページ20に含まれる内容の要旨
4. Coloque el cable a través del agujero. 5. Coloque el aro de montaje sobre el agujero. 6. Conecte los cables al altavoz observando la polaridad del mismo. 7. Coloque el altavoz en el agujero y atornillelo. Tenga cuidado en no doblar el soporte del altavoz durante este paso. 8. Presione la reja del altavoz sobre el aro de montaje. Montaje empotrado del Tweeter 1 1. Corte un agujero de 1 ⁄4" (32mm). 2. Coloque los cables a través del agujero de montaje. 3. Conecte los cables observando la polari
