ページ1に含まれる内容の要旨
OPERATING INSTRUCTIONS
ENGLISH pp.1-8
®
ESPAÑOL pág 9-13
Commercial
FRANÇAIS p. 14-18
Lightweight
Record and retain
Cleaner with
Model_________________ Serial No._________________
Dirt Cup
(Located on bottom of cleaner)
Important Safeguards
When using an electrical appliance, always follow
basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
Warning: To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
•
ページ2に含まれる内容の要旨
UP It is extremely important to read and 1. Assembling cleaner follow all the assembly steps in order. Carton contents 1-1 D C B A E H F G Remove all parts from carton and A.Upper handle F. Handle bolt and nut packet (One extra nut identify each item shown. Make B.Lower handle included) sure all parts, especially small C.Cord items, such as G and F, are locat- G. Dirt cup screws (2) D.Dirt cup assembly ed before disposing of cardboard H. Dirt cup support packaging. E. Cleaner body Step 1 Assembl
ページ3に含まれる内容の要旨
1-4 1-5 F F I F H With (F) pointing downward (toward Rotate cord protector (F) as shown. back of handle), press groove (H) into slot (I). Pull cord tight. 1-6 Step 3 Attach dirt cup assembly 1-7 A F Press cord into place at each of the three notches indicated and note correct positioning of (F). Do not plug cleaner in until assembly is totally complete. Release dirt cup latches (A) by Note proper placement of pulling them outward. cord at notch as shown. Remove cup and set it aside. 1-10 1-8 1
ページ4に含まれる内容の要旨
1-16 1-14 1-15 N Pull support toward bottom of han- With cloth bag to the front, place Push bolt into hole on lower front of dle slightly to make sure support is assembled handle onto handle base handle. locked in place. of cleaner body. If bolt will not go through hole Make sure hole in handle (N) is visi- Rock handle side to side while easily, handle is not pushed com- ble through hole in support. pushing down firmly. Extra push- pletely down. ing effort may be required. 1-17 1-18 1-19 P Q O
ページ5に含まれる内容の要旨
2-2 2-3 2-4 A B Transporting cleaner Edge cleaning Belt storage To move your cleaner from room to Edge cleaning is provided on Lift door to conveniently store extra belt. room, put handle in upright position, tilt both sides of nozzle to remove dirt in cleaner back on rear wheels and push carpet near baseboards and furniture. forward (A). Guide either side of nozzle parallel to The cleaner can also be moved by lift- edge of carpet or furniture. ing it as shown in (B). 3-1 3. Maintenance 3-2 Emp
ページ6に含まれる内容の要旨
3-6 3-7 3-5 C B A Place the three tabs on bottom plate into Slip agitator through new belt (with let- Remove hood slots in front of cleaner body. Snap bot- tering toward outside of cleaner) and Place handle in operating position and tom plate into place over agitator. position belt in belt guide (A). turn cleaner over. Insert end of flat Push end of belt into opening in cleaner screwdriver into one of the four slots body. beside an arrow on bottom of cleaner. Reposition agitator making sure to a
ページ7に含まれる内容の要旨
3-11 1 Lubrication The motor is equipped with bearings 8 which contain sufficient lubrication for 4 5 6 the life of the motor. The addition of 9 12 3 10 11 7 lubricant could cause damage. Do not add lubricant to motor bearings. 2 13 The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Use this illustration for agitator reassembly, 6. Agitator end Service Center or an Authorized Hoover if necessary. Washer must be placed 7. Shaft Warranty
ページ8に含まれる内容の要旨
8
