ページ1に含まれる内容の要旨
VACUUM / BLOWER
WET AND DRY-2.2 GAL.
90981
OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2003 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
ページ2に含まれる内容の要旨
Specification ITEM DESCRIPTION Electrical Requirements 120V / 60 Hz 1.5 Peak Horsepower Double Insulated, Fan Cooled Motor Holding Capacity 2.2 Gallons Flex Hose Dimensions 1-5/8” diameter X 56-3/4” Long Overall Dimensions 11-1/4”W X 14-1/4”L X 14-3/4”H Weight 7.0 Lbs. Warning: For Indoor Use Only Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manu
ページ3に含まれる内容の要旨
7. Do not overreach. Keep proper footing and balance at all times. 8. Always use protection. Wear ANSI approved safety impact eye glasses when using this product. ANSI approved safety impact eye glasses are available from Harbor Freight Tools. 9. When necessary, use hearing and breathing protection. Wear ANSI approved hearing protectors when using the Vacuum/Blower for extended time periods or using it in a noisy work area. For dusty operations, wear an ANSI approved dust mask. ANSI approved hea
ページ4に含まれる内容の要旨
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS 1. DO NOT SUBMERGE THE MOTOR HOUSING (3) IN WATER OR OTHER LIQUIDS. 2. Guard against Electric Shock. Always prevent body contact with grounded surfaces such as pipes, radiators, ranges, refrigerators, etcetera. Do not handle any part of the Vacuum/Blower with wet hands when the unit is plugged in to its electrical supply source. To comply with the National Electric Code (NFPA70), and to provide additional protection from the risk of electrical shock, thi
ページ5に含まれる内容の要旨
To Vacuum Dry Materials: 1. Note: A dry bag (19) is necessary when vacuuming dry material. If the Bag is wet when vacuuming dry material, the Bag will clog quickly and become difficult to clean. If the Bag is wet, dry the Bag before performing dry vacuuming. See Figures A, B, and Assy. Diagram. 2. To remove the Motor Housing (3) in order to empty the Container (20), or clean or replace the Bag (19), pull outward on the latches located on each side of the Container. See Assy. Diagram and Figure C
ページ6に含まれる内容の要旨
To Vacuum Liquids: 1. For Vacuuming liquids it is necessary to remove the Rubber Band (18) and Bag (19). To do so, remove the Motor Housing (3) from the Container (20). Empty all debris from the Container. Remove the Rubber Band (18) and Bag from the Ball Basket (17). See Figures A, B, and Assy. Diagram. 2. The Vacuum/Blower is equipped with a Ball (16) which will automatically rise to cut off the air flow when the liquid in the Container (20) reaches the full level. When this occurs, make sure
ページ7に含まれる内容の要旨
INSPECTION, MAINTENANCE, AND CLEANING 1. CAUTION: Always disconnect the Vacuum/Blower from its electrical supply source before performing and inspection, maintenance, or cleaning. 2. Before each use, inspect the general condition of the Vacuum/Blower. Check for broken parts, damaged power cord, and any other condition that may affect its safe operation. If a problem with the Vacuum/Blower occurs, immediately discontinue using the tool and have the problem corrected before further use. Do not use
ページ8に含まれる内容の要旨
ASSEMBLY DRAWING Part 1 Part 2 Part 3 Part 16 Part 4 Part 17 Part 5 Part 18 Part 6 Part 8 Part 7 Part 19 Part 9 Part 10 Part 11 Part 12 Part 20 Part 13 Part 14 Part 21 Part 15 Part 22 NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 03/04 SKU 90981 Page 8
