ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-9302
APPLICATIONS
BMW
Mini Cooper/Cooper S 2002-2007
99-9302
KIT FEATURES
• Mounting bracket
KIT COMPONENTS
A) Mounting Bracket
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • T-33 Torx Driver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION
ページ2に含まれる内容の要旨
99-9302 TABLE OF CONTENTS Dash Disassembly - BMW Mini Cooper/Cooper S 2002-2007 . . . . . . . . . . . . . . . 1,2 Kit Assembly - DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 *Note: Refer also to the instructions included with the aftermarket radio.
ページ3に含まれる内容の要旨
99-9302 DASH DISASSEMBLY BMW Mini Cooper/Cooper S 2002-2007 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Carefully pry out both top edges of driver’s knee panel and allow panel to hang. (Figure A) 3 Remove (2) Torx T-33 screws from driver’s side rail trim. (Figure B) 4 Remove (2) Torx T-33 screws from B passenger side rail trim. (On specially equipped models, it may be necessary to open the glove box to access these (2) screws) (Figure C) C 1
ページ4に含まれる内容の要旨
99-9302 DASH DISASSEMBLY BMW Mini Cooper/Cooper S 2002-2007 D 5 Remove (1) Phillips scew from each cup holder. (Figure D) 6 Carefully pry up mirror adjustment switch panel and remove (2) Phillips screws. (Figure E) 7 Slide cup holder/gear shift assembly toward rear of car and carefully remove side rail trims. (Figure F) 8 Remove (4) Phillip screws securing E radio. Pull out radio, disconnect and remove. (Figure G) G F 2
ページ5に含まれる内容の要旨
99-9302 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio open- ing of the Radio Housing and secure by bending the metal locking tabs out- ward. (Figure A) 2 Slide the aftermarket radio unit into the cage until it snaps into place. (Figure B) Continue to final assembly. B 3
ページ6に含まれる内容の要旨
99-9302 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
ページ7に含まれる内容の要旨
99-9302 NOTES 5
ページ8に含まれる内容の要旨
99-9302 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 06/19/07 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION INST99-9302
