ページ1に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 1
ページ2に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 2 Congratulations! Congratulations on purchasing Universal Remote Control’s WR7 7-Component Pre--Programmed and Learning remote control. You now have the power to control your entire home entertainment system with one easy--to--use remote. The WR7 can be used with thousands of audio/video components because of the extensive library of codes that have already been programmed into the remote. So... get ready to sit back, relax, and simplify your home entertainment
ページ3に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 3 Table of Contents Getting Started - Overview • Control up to 7 Components………………….......5 • Activating Component Buttons………………….....5 • Learning Capability……………………………........5 • AUX Function………………………......................6 • Light Button......................................................6 • Battery Installation............................................6 • Low Battery Warning…………………………........6 • Couch Mode……….………….........…...............6 Special Advanced Fe
ページ4に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 4 Programming Special Advanced Features ™ • MacroPower Total System On/Off......................21-22 • ‘My Favorites’ – Favorite Channels......................23-24 ™ • SimpleSound Total System Volume Control...........25-26 • Channel Control ‘Punch Through’.........................27 • Transport Control ‘Punch Through’........................28 • OSD (On-ScreenDisplay) Control ‘Punch Through’.......29 Erasing Commands - Overview.............30 • Erasing a Single L
ページ5に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 5 Getting Started - Overview Control up to 7 Components The WR7 remote control is designed to control up to seven different Audio/Video components and operate virtually all brands of AUDIO, TV, DVD, VCR/DVR, CD, SAT/CABLE and AUX (Light, Music Server, etc.) components. Activating Component Buttons Once you have programmed the WR7 for all of your components, all you need to do is press a component button and all the buttons on the WR7 will work with that compone
ページ6に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 6 AUX Function The AUX (Auxillary) button is designed to operate a 7th audio/video component that you may have in your system… such as a TIVO, a second VCR or DVD, or an additional audio component. Light Button The WR7 features a fully backlit keypad for ease of use in low light or darkened viewing conditions. Press the LIGHT button to backlight all the keypad buttons. Press again to turn off (or simply wait 10 seconds for automatic shut-off). Battery Installa
ページ7に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 7 Special Advanced Features The WR7 also offers the following special advanced features that can offer you many time-saving conveniences: ™ MacroPower & Other Macro Buttons MacroPower is a unique feature that enables you to turn all your components ON or OFF, all at the same time, simply with the press of one button. The WR7 has 13 Macro buttons that are designed to store up to 20 commands in each button. Pressing any one of the Macro buttons will send out the
ページ8に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 8 Keypad Layout & Button Functions Allows you to turn the ON SYSTEM OFF selected component on Designed to send Power and off. On/Off commands for up to seven components AUD, CD, VCR, with one button press. AUX, TV, DVD, SAT/CABLE Used to select the component you FAVORITE want to operate and signals Displays FAVORITE CHANNEL remote control activity. listings through the SAT/CABLE Selects the video INPUT set top box. source from avail- able components. CHANNEL Selects
ページ9に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 9 Programming WR7 using Pre-Programmed Codes There are three ways you can program your WR7 using the component brand codes that are pre-programmed into the remote. • Quick Set-Up Method • Three-Digit Code Entry Method • Auto--Search Method The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using one-digit codes for up to 10 major brands for each component. The Three-digit Code Entry Method allows you to set-up the W
ページ10に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 10 STEP 3: Release the component button to save the code. The component LED light will blink three times to confirm that the code has been stored. Repeat the above steps for other components. COMPONENT BUTTONS NUMBER PAD Page 10
ページ11に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 11 Three-Digit Code Entry Method STEP 1: Find the 3-digit code numbers assigned to your brand from the lists in the back of this manual. The codes are listed by component category (i.e., TV, VCR, DVD, etc.), then by brand name. For instance, if you would like to locate a code for a Sony television, first locate the TV category and then look for the Sony brand. STEP 2: Once you have located the 3-digit codes for each of the components that you wish to operate with
ページ12に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 12 IMPORTANT: You have 30 seconds to perform the next step while you are in programming mode. If you do not press a button within 30 seconds, the component LED light will turn off. The remote will exit the programming mode and you will have to start over. STEP 5: Point the WR7 toward the component (in this example the TV) and punch in the first 3-digit code that you wrote down for that specific component. Use the Number buttons 0~9 on the remote to punch in the cod
ページ13に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 13 STEP 7: Once you’ve entered a correct code, you must save it. Press the component button you just programmed (in this case TV) one more time to save the code number. The component LED light will blink three times to confirm that the code was successfully stored. Now when you press the TV component button, all of the buttons will work with your TV. Program the remaining components by repeating steps 3 through 7. IMPORTANT: If you have tried all the set-up cod
ページ14に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 14 Auto-Search Method The Auto-Search Method is a way you can scan through all of the codes in the table to find the right code for your component. STEP 1: Manually or using your old remote, turn on the component you want to program—for example, to program your TV, turn on your TV set. STEP 2: On the WR7, press the Component button that you want to program (in this case the button that says TV) and the SELECT [SEL] button at the same time. Hold down both button
ページ15に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 15 STEP 3: Point the WR7 remote control toward the component and press the UP [ ] arrow (or DOWN [ ] arrow) button once. Each time the UP or DOWN arrow button is pressed, the code will count up (or down) one code number and send a Power OFF signal. When the correct code is sent out, the component will turn off. STEP 4: Once you have found the right code number and the component has turned off, press the POWER [ON] button on the WR7 remote to turn the compone
ページ16に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 16 Programming WR7 using the Learning Method STEP 1: Line up the WR7 to the remote control you want to ‘learn’ from, head--to--head as shown below. Start with both remotes’ IR windows touching (or nearly touching). STEP 2: On the WR7, press the Component button that you want to program (in this case the button that says TV) and the ENTER [ENT] button at the same time. Hold down both buttons for two seconds until the TV Component button light turns on. This signals
ページ17に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 17 STEP 4: Press and hold the [MUTE] button on the other remote until the component button LED on the WR7 blinks twice. Now you can continue learning all other buttons from your old remote by pressing the next button on the WR7 and repeating this step. Note: The component LED will blink five times if there was an error in the learning process. In this case, please repeat Steps 3 and 4. STEP 5: Once the WR7 has learned all the buttons in the selected component mode
ページ18に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 18 Here are some additional facts regarding the Learning process: • Learned functions override any existing pre-programmed functions on the remote control • Learned functions are automatically erased when a new function is learned on the same button • Learned functions are retained even after a different set-up code number is programmed into the remote control • To return to an original pre-programmed function, a learned function must be erased • Rapidly tapping t
ページ19に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 19 AUX Function: Programming a 7th Component After you’ve finished programming the WR7 for six primary com- ponents and you did not use AUX, you can take advantage of the AUX function to program a 7th component, such as a second TV, DVD, or any other audio/video component that you may have in your system. Simply program the [AUX] button in the same manner as any other component using either the Quick Set-Up Method, the 3-Digit Code Entry Method, the Auto-Search Me
ページ20に含まれる内容の要旨
WR7 1/13/08 12:18 PM Page 20 STEP 2: Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code. Next it will pause for about one second and begin blinking again to indicate the number of the second digit. Then once again it will pause, then blink, to indicate the number of the third digit. Example: One blink, pause, eight blinks, pause, three blinks indicates code number 183. Note that ten (10) blinks represent the
