ページ1に含まれる内容の要旨
text_dishpvr.fm Page 1 Tuesday, March 2, 2004 12:35 PM
TABLE OF CONTENTS
Remote Control Basics....................................... 2
Models Supported by this Guide......................... 2
UHF and IR Signals ............................................ 3
Installing Batteries............................................... 3
Converting the 6.0 Remote Control ................... 4
Setting Up to Control the Satellite Receiver ..... 5
Checking the Remote Address .......................... 8
S
ページ2に含まれる内容の要旨
text_dishpvr.fm Page 2 Tuesday, March 2, 2004 12:35 PM REMOTE CONTROL BASICS This remote control gives you easy access to all the features of a DISH Network satellite TV receiver. You can set up the remote to control the satellite TV receiver and up to three other devices. These devices can be a TV, a VCR or DVD player, and a third device. MODELS SUPPORTED BY THIS GUIDE This user’s guide supports the following remote control models as shown on the label on the back of the remote: • 5.0 -
ページ3に含まれる内容の要旨
text_dishpvr.fm Page 3 Tuesday, March 2, 2004 12:35 PM INSTALLING BATTERIES The remote control requires AAA batteries. When you replace old batteries, you should replace all of the batteries. Use batteries of the same kind, for example, alkaline or carbon zinc, and don’t mix batteries of different kinds. Alkaline batteries last longer. 1. Press down on the battery cover and slide the cover off. 2. If you are replacing batteries, take out all of the old batteries. 3. Put the new batterie
ページ4に含まれる内容の要旨
text_dishpvr.fm Page 4 Tuesday, March 2, 2004 12:35 PM CONVERTING THE 6.0 REMOTE CONTROL By replacing the key at the bottom of the 6.0 remote, this remote can be converted to look and work like a 5.0 IR or to operate like a second UHF Pro remote to control the side of the DISH Player-DVR 522 receiver. The instructions that follow show you how to replace this key. After replacing the key, follow the instructions in Setting Up to Control the Satellite Receiver. Note: If you do not need to
ページ5に含まれる内容の要旨
text_dishpvr.fm Page 5 Tuesday, March 2, 2004 12:35 PM 5. If you are converting the remote to operate like a second UHF Pro remote to control the side of the DISH Player-DVR 522 receiver, then get the green 1 UHF Pro key provided separately. Install this key in the remote with the UHF Pro marking showing. Note: Key has the UHF Pro marking. If you set up your DISH Player-DVR 522 to operate the side using UHF Pro, the two UHF Pro remotes for this receiver will interfere with each
ページ6に含まれる内容の要旨
text_dishpvr.fm Page 6 Tuesday, March 2, 2004 12:35 PM 1. For DISH Player-DVR 522 receivers only: If you are using a 6.0 remote control with the green 1 UHF Pro key installed, perform the steps a. through e. below. If not, then go to step 2. a. Open the TV1 UHF Pro Setup screen by pressing MENU-6-1-6 on the remote control. b. Select Enable from the TV1 UHF Pro Setup screen. c. Press the SYS INFO button on the front panel to open the System Information screen. d. Move the highlight to the
ページ7に含まれる内容の要旨
text_dishpvr.fm Page 7 Tuesday, March 2, 2004 12:35 PM 4. Use the number buttons to enter any number from 1 to 16. The SAT mode button goes out after you enter each digit, and then lights up again. Write down the number you entered: 5. Press the POUND (#) button. If you entered the address correctly, the SAT mode button will flash three times. 6. Press the RECORD button. If you are using a 6.0 remote with the green 1 key (no UHF Pro marking), you must point the remote control at the rec
ページ8に含まれる内容の要旨
text_dishpvr.fm Page 8 Tuesday, March 2, 2004 12:35 PM CHECKING THE REMOTE ADDRESS To read out the remote control address setting: 1. Press and hold the SAT mode button for three seconds until all mode buttons light. Then, let go. 2. Press the POUND (#) button twice while watching the SAT mode button. 3. Count the number of times the SAT mode button flashes. This number is the remote address. For example, if the SAT mode button flashes 6 times, this indicates the remote address is set t
ページ9に含まれる内容の要旨
text_dishpvr.fm Page 9 Tuesday, March 2, 2004 12:35 PM SETTING UP USING DEVICE CODE TABLES You can set up the remote to control other devices using the device codes listed on page 29. 1. Use the device’s buttons or its remote control to turn on the device. 2. Find the brand name of the device in the tables starting on page 29. If the brand isn’t listed, see Setting Up Using Device Codes Scan on page 10. 3. Press and hold the mode button for the device you want the remote to control, for
ページ10に含まれる内容の要旨
text_dishpvr.fm Page 10 Tuesday, March 2, 2004 12:35 PM 10.If the code you entered doesn’t work, do steps 3 through 9 again with another device code from the tables. 11.If you cannot find a code that works, try Setting Up Using Device Code Scan. SETTING UP USING DEVICE CODE SCAN If the code for your device is not listed in the tables on starting page 29, use this procedure to scan the remote control’s memory for the device code. Here’s what to do: 1. Use the device’s buttons or its remote
ページ11に含まれる内容の要旨
text_dishpvr.fm Page 11 Tuesday, March 2, 2004 12:35 PM 7. Press the blank POWER button to turn the device back on. 8. Try some other buttons to make sure they work. Sometimes, the blank POWER button works when other buttons don’t. CHECKING THE DEVICE CODES You can find out what device code you’ve set for each remote control mode. 1. Press and hold the mode button for the device you want the remote to control, for about three seconds. When all the other mode buttons light up, let go of
ページ12に含まれる内容の要旨
text_dishpvr.fm Page 12 Tuesday, March 2, 2004 12:35 PM To set the remote to control the device’s volume: 1. Press and hold the AUX mode button for three seconds, and then let go of it. The AUX mode button will blink. 2. Press the POUND (#) button. 3. Press the plus (+) side of the VOLUME button. 4. Press the 0 number button. 5. Press the POUND (#) button. The AUX mode button flashes three times. 6. Press the SAT mode button. 7. Press the plus (+) and minus (-) sides of the VOLUME button.
ページ13に含まれる内容の要旨
text_dishpvr.fm Page 13 Tuesday, March 2, 2004 12:35 PM 7. Press the plus (+) and minus (-) sides of the VOLUME button. The TV’s volume changes and the TV mode button lights instead of the AUX mode button. REMOTE CONTROL OPERATION OPERATING MODES You can set the remote to four different modes to control the receiver or other devices. You may need to change the remote address to operate the receiver. See Setting Up to Control the Receiver on page 4. You must set up the remote to control
ページ14に含まれる内容の要旨
text_dishpvr.fm Page 14 Tuesday, March 2, 2004 12:35 PM TV/VIDEO BUTTON If you connect the receiver with its back panel TV ANTENNA/CABLE IN and TV SET OUT ports, use this button to switch the receiver between the satellite signal (connect it to the SATELLITE IN port) and another video signal like a cable or broadcast TV antenna input (connect it to the receiver’s TV ANTENNA/CABLE IN input). Note: Your remote control will either have the TV/VIDEO button or the SD/HD INPUT button, but not
ページ15に含まれる内容の要旨
text_dishpvr.fm Page 15 Tuesday, March 2, 2004 12:35 PM MUTE BUTTON Press this button to turn the TV sound on or off. Note: You must set up the remote to control the TV for the MUTE button to work. See Setting Up to Control Other Devices on page 8. MENU BUTTON Press this button to open the Main Menu. PAGE UP AND PAGE DOWN BUTTONS Press the PAGE UP button or the PAGE DOWN button to scan, page by page, through the Program Guide, a Themes list, a Favorite List, an Event Timers list, or a l
ページ16に含まれる内容の要旨
text_dishpvr.fm Page 16 Tuesday, March 2, 2004 12:35 PM • Show Themes - Press the LEFT arrow button. • Move around within the Program Guide, menus, and Browse Banner - Press the UP, DOWN, LEFT, and RIGHT arrow buttons. SELECT BUTTON Press this button to select the option you highlight in a menu. Note: The SELECT button may also be labeled SELECT/OK. RECALL BUTTON Press this button to go back to the last receiver channel you watched. Press it again to switch between the last two receiver
ページ17に含まれる内容の要旨
text_dishpvr.fm Page 17 Tuesday, March 2, 2004 12:35 PM CANCEL BUTTON Press this button to cancel and go back to the previous menu or to watch a program. DISH BUTTON Press the dish button to go to DISH Home Interactive TV for receivers that support this feature. NUMBER BUTTONS • Change the channel - Use the NUMBER buttons to enter a channel number to change the channel. If you have the Program Guide open, use the NUMBER buttons to jump to the channel listing on the Program Guide. • S
ページ18に含まれる内容の要旨
text_dishpvr.fm Page 18 Tuesday, March 2, 2004 12:35 PM STAR BUTTON Press the STAR button to back space while using the search function of your receiver. Note: Your remote control will either have the STAR button or the FORMAT/STAR button, but not both. FORMAT/STAR BUTTON Press the FORMAT/STAR button to toggle through the available display modes (Normal, Zoom) on widescreen displays. Note: Your remote control will either have the STAR button or the FORMAT/STAR button, but not both. POU
ページ19に含まれる内容の要旨
text_dishpvr.fm Page 19 Tuesday, March 2, 2004 12:35 PM PLAY BUTTON Press the PLAY button to play back a recorded event. Also, press this button to switch from pause, fast forward, or back to normal play back. STOP BUTTON Press the STOP button to stop recording a program or to stop playing a recorded program. PAUSE BUTTON Press the PAUSE button to pause a program. Press this button again to go back to watching the program. FWD BUTTON Press the FWD (“forward”) button to: • Move ahead throu
ページ20に含まれる内容の要旨
text_dishpvr.fm Page 20 Tuesday, March 2, 2004 12:35 PM SKIP FWD BUTTON Press the SKIP FWD button to: • Skip ahead about 30 seconds in a program. Press this button again to skip ahead again. • Skip ahead one frame at a time. To use the frame advance feature, press the PAUSE button and then press the SKIP FWD button. • Skip ahead one day at a time in the EPG. BACK BUTTON Press the BACK button to: • Move back through a program four times as fast as normal play. Press this button a second ti
