ページ1に含まれる内容の要旨
5 Wire Analog Resistive Touchscreen
FST Series Product Specifications
ページ2に含まれる内容の要旨
FST Series Product Specifications Table of Contents 1. Product Specifications...................................................................................................3 1-1. Product Applicable .............................................................................................................. 3 1-2. Structure.............................................................................................................................. 3 1-3. Environmental Specifications...
ページ3に含まれる内容の要旨
FST Series Product Specifications 1. Product Specifications 1-1. Product Applicable § This specification is applied to the 5 wire analog resistive touchscreen: FST Series. 1-2. Structure § Dimensions, structure, and shape are referred on the drawing attached. 1-3. Environmental Specifications Specification Value Operating Temperature -20°C to 70°C (no condensation) -20°C to 60°C Less than 90%RH (no condensation) Operating Humidity 3 Exceeding 60°C 133.8g/m (no condensation) Stor
ページ4に含まれる内容の要旨
FST Series Product Specifications 1-6. Appearance § Scratch, dust (W = width, L = length, D = average diameter = (longest + shortest) /2) Item Size (mm) Length (mm) Acceptable Numbers Total 0.1≥W>0.05 4≥L 1pcs in φ30mm Scratch 0.05≥W>0.03 10≥L 2pcs in φ20mm 0.03≥W 20≥L Acceptable Dust 0.1≥W>0.05 5≥L 2pcs in φ30mm Within 5pcs per product. (Linear) 0.05≥W Acceptable Acceptable 0.4≥D>0.3 *1 1pcs in Viewing Area *1 Dust 0.3≥D>0.2 2pcs in φ30mm (Circular) 0.2≥D Acceptable Applied on
ページ5に含まれる内容の要旨
FST Series Product Specifications 2. Testing Regulation 2-1. Testing Regulation § If the regulation is not specified, the test is performed under the supplier’s regulation. § Tests are performed under the room temperature unless specified. The room temperature is referred as follows: Temperature: 20°C±5°C Humidity: 65%±10%RH 2-2. Environmental Specifications § Chemical Resistance Test Condition: Tested after leaving the chemical on the surface for 12 hours being wiped off by cloth.
ページ6に含まれる内容の要旨
FST Series Product Specifications 2-4. Electrical Characteristics § Terminal Resistance Test Condition: Top and bottom electrodes are measured at the terminal. Judgement: Must satisfy the specification. § Insulation Resistance Test Neighboring Terminals: Measured by applying the reference voltage to the terminals Active Area Electrodes: Measured by applying the reference voltage to the top and bottom electrodes. Judgement: Must satisfy the specification. 2-5. Appearance § Appearan
ページ7に含まれる内容の要旨
FST Series Product Specifications 3. Reliability Condition 3-1. Temperature Condition § Temperature Condition Test Following test are performed in the condition with no dew condensation: Cold Test: Tested after leaving the parts in -30°C±3°C for 240 hours and in the room temperature for 2 hours. Heat Test: Tested after leaving the parts in 80°C±3°C for 240 hours and in the room temperature for 2 hours. Humidity Test: Tested after leaving the parts in the temperature 60°C±3°C, humidity
ページ8に含まれる内容の要旨
FST Series Product Specifications 5. Handling Notes 5-1. Precautions § This product is intended for use in standard applications (computers, office automation, and other office equipment, industrial, communications, and measurement equipment, personal and household devices, etc.) Please avoid using this product for special applications where failure or abnormal operation may directly affect human lives, or cause physical injury or property damage, or where extremely high levels of reliab
ページ9に含まれる内容の要旨
FST Series Product Specifications 5-5. Mounting Notes § Gap between the Bezel and Touchscreen Bezel A gap of approximately 0.5mm is needed between the bezel Top Electrode and the top electrode. It may cause unexpected input if the gap is too narrow. § Cushion If a cushion is used between the bezel and the top electrode, Bezel Cushion the cushion must be free enough to absorb the expansion and contraction difference between the bezel and the top electrode. If the cushion is squash
ページ10に含まれる内容の要旨
FST Series Product Specifications 6. Warranty 6-1. Warranty Period § The warranty period is limited to 3 years from the date of shipping. The warranty for the initial defection such as appearance defection is limited to 1 month. § Any defected parts under proper use will be examined by the supplier and replaced by the new parts if the defection is considered to be caused by the supplier. § The replacement is subject to be included in the next lot. 6-2. Warranty Target § The warranty
ページ11に含まれる内容の要旨
FST Series Product Specifications 7. Revision history Rev1.0 (May 11, 2005) Initial release Rev1.1 (July 13, 2005) 4-1.Recommended Connector is changed RE-H052SD-1130 to RE-H052SD-1110. 6-1.Warranty Period is changed 5 years to 3 years. Rev2.0 (October 13, 2006) The specification item name was changed. 1-3.”Storing Temperature” to “Storage Temperature” 1-3.”Storing Humidity” to “Storage Humidity” 1-4.”Operating Load” to “Activation Force” 1-4.”Light Transmissivi
ページ12に含まれる内容の要旨
FST Series Product Specifications FST Series Product Specifications Rev. 2.0, October 13, 2006 © 2005 - 2006 DMC Co., Ltd. This document can be freely distributed, but any alternation to this document is prohibited. http://www.dmccoltd.com th 9 floor, Kanda Sento Building, 1-2-4 Yushima, Bunkyo-Ku, Tokyo 113-0034, Japan Phone: +81-3-5209-7131 (Japanese), 7135 (English) Fax: +81-3-5209-7130 12 Rev. 2.0 ©2005 -
