ページ1に含まれる内容の要旨
Assembly Instructions for Model: VMAA26
Thank you for choosing a Sanus Systems VisionMount™ wall mount. The VMAA26 is designed to mount up to 50” Flat panel televisions
weighing up to 130 lb. to a vertical wall. It allows you to tilt the television from +5° to -15°. It will also extend 25.75” away from the wall,
swivel up to 180°, and roll ± 6°.
CAUTION: The size and weight of your television must not exceed 50” [1270 mm] diagonally and 130 Lbs [59 Kg]. The wall
must be capable of suppor
ページ2に含まれる内容の要旨
Hardware: (Hardware shown is actual size) Wire Tie - H Wire Tie Clip - G Qty. 10 Qty. 7 Lag Bolt - I Lag Bolt Washer - J 7/32 & 3/16 Allen Keys - K Qty. 4 Qty. 4 Qty. 1 Each 1/4-20 Nut - M Preventor Bolt - O Safety Bolt - N 2” Carriage Bolt - L Qty. 4 Qty. 2 Qty. 3 Qty. 4 Supplied Television Mounting Hardware: (Hardware shown is actual size) M4 x 12 mm Bolt - P M5 x 12 mm Bolt - Q M6 x 12 mm Bolt - R M8 x 16 mm Bolt - S Qty. 4 Qty. 4 Qty. 4 Qty. 4 M4 x 30 mm Bolt - T M5 x 30 mm Bolt - U M6 x 35
ページ3に含まれる内容の要旨
Step 1: Mounting Monitor Brackets to a Televisions with a flat back NOTE: For TVs with a curved back or any other obstruction See Step 2. After completing this step, proceed to Step 3. Determine the diameter of the Bolt (P,Q,R,S) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately. Once you have determined the correct diameter, refer to the appropriate Diagram below. Thread the Bolt through the appropriate Lo
ページ4に含まれる内容の要旨
Step 2: Mounting the Monitor Brackets to Televisions with a curved back or other obstruction. Determine the diameter of the Bolt (T,U,V,W) your TV requires, by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately. Once you have determined the correct diameter, refer to the appropriate Diagram below. Thread the Bolt through the appropriate Lock Washer (X,Y,Z,AA), a Washer (DD,EE), the Monitor Bracket (E), a second Washer (DD - M4/
ページ5に含まれる内容の要旨
Step 3: Add the Vise Assemblies to the Monitor Brackets: NOTE: Do not overtighten the 1/4-20 Nut (M). The Vise Assembly (F) should be able to rotate freely around the Carriage Bolt (L). Place the Vise Assembly (F) into the Monitor Bracket (E) so that the two Jaws point toward the set of 1” diameter holes and the Allen Bolt is facing away from the television. Place a 2” Carriage Bolt (L) through the square hole in the side of the Monitor Bracket, and the Vise Assembly; then, through the squar
ページ6に含まれる内容の要旨
Step 4: Attach the Arm Assembly to the Television (Continued) CAUTION: The 1” Diameter Tubes (D) must extend beyond the outside edges of both Monitor Brackets (E) and the Allen Bolts in all 6 Vise Assemblies (F) must be tightened. Failure to do this will result in an installation that unstable and may result in property damage and/or personal injury. Position the Arm Assembly (B) so the hook shaped tab shown in Detail View of Diagram 4b is on the top. Line up the two 1” diameter holes in
ページ7に含まれる内容の要旨
Step 6: Hang the assembly onto the Wall Plate CAUTION: This step may require two people to lift the assembly onto the Wall Plate. Sanus is not responsible for property damage and/or personal injury. Orient the Arm Assembly (B) so the arm extends directly away from the television and the Transfer Plate is parallel with the television. Lift the assembly and hook the Transfer Plate onto the tab on the top of the Wall Plate (A) as shown in Diagram 6a. Horizontally adjust the Transfer Plate s
ページ8に含まれる内容の要旨
Step 8: Add Preventor CAUTION: Avoid Pinch Points. Placing your hands or fingers between moveable parts (Pinch Points) may result in personal injury Determine which direction you want the Arm to fold. If you want the Arm to fold to the right, place the Preventor (C) on the right side of the Arm Assembly (B). If you want the Arm to fold to the left, place the Preventor on the left side of the Arm Assembly. Position the Preventor so the flat side is facing the Idler as shown in the Detaile
