ページ1に含まれる内容の要旨
INSTALLATION MANUAL
PSD-BW/PSD-BWL
Nesting Cart Series
AUSTRALIA,NEW ZEALAND,
NORTH AMERICA EUROPE OCEANIA (Distributor)
3130 East Miraloma Avenue Swallow House, P.O. Box 295
Anaheim, CA 92806 USA Shilton Industrial Estate, Mordialloc Victoria 3195
USA and Canada – Shilton, Coventry, England CV79JY Australia
Phone: 800-368-9700 Phone: +44 (0) 2476 614700 Phone: 03 9586 6330
Fax: 800-832-4888 Fax: +44 (0) 2476 614710 www.premiermounts.com.au
Other Locations – Phone: 001
ページ2に含まれる内容の要旨
PSD-BW/L Table of Contents WARRANTY ....................................................................................................................................................- 2 - CONTACT PREMIER MOUNTS ....................................................................................................................- 2 - WARNING STATEMENTS .............................................................................................................................- 3 -
ページ3に含まれる内容の要旨
PSD-BW/L Warning Statements WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS. WARNING: THE FLOOR ST
ページ4に含まれる内容の要旨
PSD-BW/L Parts List Congratulations on purchasing the PSD-BW/PSD-BWL Nesting Cart. The PSD-BW/PSD-BWL Nesting Cart is shipped with all proper installation hardware and components. Please verify that none of these parts are missing and/or damaged before assembly. If there are parts missing and/or damaged, please stop the assembly and contact Premier Mounts (800) 368-7000. NOTE: Some mounting configurations will allow for a “landscape” orientation. In these situations, when moving the
ページ5に含まれる内容の要旨
PSD-BW/L BW Base Castor Installation (Figure 1) Unpack the PSD-BW/L Nesting Cart and review any WARNING statements that apply to the installation. Select the desired location for the PSD-BW/L Nesting Cart. Locking Castor Non-Locking Castor Figure 1 1. Place the BW/L on a flat surface. NOTE: Make sure the locking castors (Qty 2) are attached to the rear legs of the Nesting Cart. 2. Insert each castor into the threaded mounting point located on the underside of the BW/L base (Fig
ページ6に含まれる内容の要旨
PSD-BW/L PSD-SPA Installation (Figure 3) NOTE: Use of the PSD-SPA will depend on the mount that is used. All PSM/CTM Series mounts require using the PSD-SPA. The Revolution Series, USA and UFA Mounts, however, do not require the use of the PSD-SPA. 1. Slide the PSD-SPA over and down the support tubes. 2. Once the desired height has been determined, tighten the four (4) M8 x 10mm set screws, using the 5/32” Allen wrench (supplied) to secure the PSD-SPA (Figure 3). PSD-SPA 5/32” Al
ページ7に含まれる内容の要旨
PSD-BW/L Optional Mounting Configurations CTM-Series Revolution Series USA/UFA Series Page 7 Installation Instructions
ページ8に含まれる内容の要旨
PSD-BW/L Technical Specifications All measurements are in inches (mm). PSD-BWL PSD-BW Notes Installation Instructions Page 8
ページ9に含まれる内容の要旨
Installation Instructions Installation Instructions Installation Instructions Installation Instructions Rotary Tilt Mount Model: RTM-L AUSTRALIA, NEW ZEALAND, NORTH AMERICA OCEANIA (Distributor) EUROPE 3130 East Miraloma Avenue Swallow House, P.O. Box 295 Mordialloc Victoria 3195 Anaheim, CA 92806 USA Shilton Industrial Estate, USA and Canada - Shilton, Coventry, England CV79JY Australia Phone: 03 9586 6330 Phone: 800-368-9700 Phone: +44 (0) 2476 614700 Fax: 800-832-4888 www.premiermounts.com.au
ページ10に含まれる内容の要旨
RTM-L TABLE OF CONTENTS Warranty 2 Contact Premier Mounts 2 Warning Statements 3 Parts List 4 Installation Tools 4 Thread Depth Indicator 7 Mount Installation 8 Universal Mounting Bracket Installation 9 Display Orientation 11 Securing the Display 11 Tilt Positioning 12 Optional Configurations 12 Technical Specifications 12 Addendum 13 PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from def
ページ11に含まれる内容の要旨
RTM-L Warning Statements WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS. WARNING: THE MOUNTING SURFACE MUST
ページ12に含まれる内容の要旨
RTM-L Parts List NOTE: This mount is shipped with all installation hardware and components. Make sure that none of these parts are missing and/ or damaged before beginning installation. If there are parts missing and/or damaged, please stop and contact Premier Mounts (800) 368-9700. Griplate™ (Qty 8) Universal Mounting Brackets (Qty 2) Hand Crank (Qty 1) M6 Knurl Knob (Qty 1) Rotary Tilt Mount (Qty 1) Installation Tools Phillips Head Screw Driver Soft Material/ Blanket Pencil Tape Measure Thre
ページ13に含まれる内容の要旨
RTM-L Parts List (Cont.) (Qty 8) (Qty 8) M4 x 16 M6 x 20 (Qty 8) M4 x 25 (Qty 8) M6 x 30 (Qty 8) M5 x 12 M6 x 45 (Qty 8) (Qty 8) M5 x 16 M8 x 20 (Qty 8) (Qty 8) M5 x 20 (Qty 8) (Qty 8) M8 x 25 M5 x 25 (Qty 8) M5 x 50 M8 x 30 (Qty 8) (Qty 8) M6 x 16 M8 x 35 (Qty 8) M8 x 45 (Qty 8) M8 x 70 (Qty 4) Installation Instructions Page 5
ページ14に含まれる内容の要旨
RTM-L Parts List (Cont.) Nylon spacers and flat washers' actual size NOTE: The nylon spacers may be stacked to achieve proper spacing. 9/16" Nylon spacers 1/4" Nylon spacers (large) (Qty 8) (Qty 8) 1/2" Nylon spacers Nylon sleeves (large) (Qty 8) (Qty 12) 5/16" Flat washers (metal) (Qty 8) 1" Nylon spacers (Qty 8) 1/4" Nylon spacers (Small) (Qty 8) Page 6 Installation Instructions
ページ15に含まれる内容の要旨
RTM-L Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). 3. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3), until you find one that comes closest to your mark without going past. 4. If your
ページ16に含まれる内容の要旨
RTM-L Mount Installation NOTE: The installation instructions that are contained in this manual refer only to the RTM-L. The installation instructions for the various bases that are used with the RTM-L will be included with those products. NOTE: Prior to installing the RTM-L, the mounting configuration must already be assembled (base, support poles, etc.). Mounting Block Set Screws Cradle Support Poles 2. To secure the mounting block to the support 1. Slide the mounting block poles, tighten t
ページ17に含まれる内容の要旨
RTM-L Universal Mounting Bracket Assembly 1. Place the universal bracket bar and the universal brackets on a flat surface. 2. Slide the universal brackets onto the universal bracket bar (as shown below) with the set screws facing up. At this time, do not tighten the set screws that are located on the universal bracket. 3. Place the display on a soft, flat surface, face-down. Next, place the universal bracket assembly on the back of the display, with the universal brackets resting directly over
ページ18に含まれる内容の要旨
RTM-L 3. Lower the universal bracket bar and display into the cradle (as to the left). Nylon Sleeve NOTE: The circular portion of the universal bracket bar must rest inside the nylon sleeve. If seated improperly, the operation of the RTM-L will be hindered and the nylon sleeve will become damaged. Knurl Knob Mounting Points (a knurl knob may be placed in either mounting hole) 4. Insert an M6 knurl knob into the knurl knob mounting point and tighten. Locking Screws 5. Tighten the two (2) P
ページ19に含まれる内容の要旨
RTM-L Display Orientation The RTM-L will allow the user to adjust the display a full 360°. WARNING: BEFORE ROTATING THE RTM-L, MAKE SURE THAT THE M6 KNURL KNOB IS SECURELY FASTENED TO THE RTM-L. ALSO, PLEASE MAKE SURE YOU ALLOW ENOUGH CABLE AND WIRE CLEARANCE FOR FULL ROTATION. 1. To adjust the RTM-L, rotate the display either clockwise or 2. Tighten the two counter-clockwise. Phillips head locking screws (see Step 5, Page 10). Tilt Positioning Rotate the crank handle to tilt the RTM-L: Down
ページ20に含まれる内容の要旨
RTM-L Optional Configurations PSD-EB PSD-BW PSD-TS Technical Specifications All measurements are in inches (mm). Page 12 Installation Instructions
