ページ1に含まれる内容の要旨
Models: PLA 60, PLA 60-S,
Installation and Assembly - Articulating Swivel Arm for
PLAV 60, PLAV 60-S
37" - 60" Plasma Screens
This product is UL Listed. It must be
installed by a qualified professional
installer.
Maximum UL Load Capacity: 175 lb (79 kg)
3215 W. North Ave. • Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708) 865-2941 www.peerlessmoun ts.com
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06
ページ2に含まれる内容の要旨
Read instruction sheet before you start installation and assembly. WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307. This product should only be installed by a qualified professional. Make sure that the supporting surface will safely support the combined load
ページ3に含まれる内容の要旨
Before you start make sure all parts D M Parts List listed are included with your product. PLA 60 PLA 60-S PLAV 60 PLAV 60-S DESCRIPTION QTY. PART # PART # PART # PART # A wall plate 1 201-1040 201-4040 201-1040 201-4040 B tilt-roll assembly 1 201-1093 201-4093 201-1048 201-4048 E C arm assembly 1 201-1072 201-4072 201-1049 201-4049 D wall support arm axle 1 201-1041 201-1041 201-1041 201-1041 F E vinyl trim 3 600-1012 600-1012 600-1012 600-1012 F M10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262
ページ4に含まれる内容の要旨
Installation to Wood Stud Wall WARNING Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for a
ページ5に含まれる内容の要旨
Installation to Concrete Wall WARNING Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Never exceed the Maximum UL Load Capacity of 175 lb (79 kg). Never mount this product to metal studs. IMPORTANT! Concrete must be 2000 psi density minimum. concrete 1 surface Use wall plate (A), making sure that it is lev
ページ6に含まれる内容の要旨
WARNING If you are uncertain that product is properly installed, call customer care. Note: There are five mounting positions. The N 2 center position is shown (right). Slide washer (J) J over wall support arm axle (D). Next, insert plastic cap (N) into axle. Then, insert holding pin (M) into D axle. See detail 1. M Place arm assembly (C) with washer (J) into wall 2-1 plate (A). Insert axle assembly shown in detail 1 DETAIL 1 through wall plate (A), arm assembly (C), and washer (J). Lock axle i
ページ7に含まれる内容の要旨
Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm 4 assembly (C). Insert one finishing cap (L) into each unused hole of wall plate (A). 4-1 L A SWIVEL BOX C E Note: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceeding with step 5. If your adapter bracket has an aluminum race attached to it, remove before proceeding and discard race. It is not used with this product. Insert
ページ8に含まれる内容の要旨
WARNING Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed 6 thread. SWIVEL BOX C .25" F Hook tilt-roll assembly (B) onto M10 screws (F). 6-1 Insert carriage bolt (I) into slot of swivel box as shown in figure 6.1. Install nylon washer (G) and tilt CAUTION adjustment knob (H). After tilt is adjusted, all fasteners must be tightened. Install remaining
ページ9に含まれる内容の要旨
Depending on the specific size & weight of the plasma, If it is too difficult to adjust roll of plasma, loosen 7-1 7 articulating swing arm may be angled at different screws shown in figure 7.1 using a phillips screw- positions, causing plasma to appear to lean sideways driver. at different articulating positions. Tilt-roll assembly (B) allows plasma to be manually adjusted, so plasma can IMPORTANT! Do not loosen or tighten screws be horizontal at all positions. To adjust, gently rotate more tha
