ページ1に含まれる内容の要旨
Lift 42
Motorized Flat Panel Lift System with
Universal Adapter.
ULN # 10235
PN # Lift 42 = L1-10235-PRO-101008vE
INSTRUCTION MANUAL
IMAGES MAY DIFFER FROM ACTUAL PRODUCT.
ページ2に含まれる内容の要旨
WARNING – ENGLISH WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING. If you do not understand the instructions or have any concerns or questions, please contact a qualified installer. North America residents can contact OmniMount customer service at 800.668.6848 or info@omnimount.com. Do not install or assemble if the product or hardware is damaged or missing. If you require replacement par
ページ3に含まれる内容の要旨
Contents Contents 1 1 Base Mount 2 1 Lift Column 1 3 1 Bayonet Bracket 4 1 Screen Support 5 1 Top Plate 6 1 Control Box 7 1 Remote Control 8 1 IR Receiver/Control switch 2 9 2 Corner brackets 10 1 Universal Adapter 11 2 Vertical Extension Rails and covers 12 1 Screen Adapter 13 1 Motor cable 14 1 Power cable 5 3 4 6 7 9 8 10 11 12 13 14 3
ページ4に含まれる内容の要旨
Contents Monitor Kit: Parts M-A through M-N are used to connect the TV to the universal adapter. Spacers may be necessary for a proper fit with recessed mounting holes or to allow access to TV inputs. Monitor Kit L-U-vA Pouch # Part # Qty Description M-A M-A M-A 4 Philips screws M4 x 15mm M-B M-B 4 Philips screws M4 x 35mm M-B M-C M-C 4 Philips screws M4 x 50mm M-D M-D 4 Philips screws M5 x 15mm M-E M-E 4 Philips screws M5 x 35mm M-C M-F M-F 4 Philips screws M5 x 50mm M-G M-G 4 Philips screws
ページ5に含まれる内容の要旨
Before Installation Prior to enclosure construction and lift assembly, please read through the below warnings and recommendations to ensure a successful installation! PINCH POINT WARNING! • Improper construction of lift enclosure can create dangerous pinch points. It is the responsibility of the installer to ensure the intended use of this product does not create hazardous pinch zones. Installation design should prevent users from inserting objects between moving parts and fixed objects
ページ6に含まれる内容の要旨
Before Enclosure Construction! Assemble lift mechanism and connect the TV to be used in the install to determine dimensions for the lift enclosure prior to construction. Be sure to leave room for adjustments If necessary. An out of cabinet assembly of the mechanism can be done using steps 1,4,6,8,9 and 10 in order. (D) (D + 2”) (W) (W + 2”) (H) (H + 2”) Minimum INTERIOR Dimensions (H) Minimum Height Height of lift in closed position or Height of TV + 2” NOTE: For use with the longer rail
ページ7に含まれる内容の要旨
Measurements Required For Cabinetry Dimensions Use previous page to find the minimum INTERIOR dimensions for custom enclosures. Width Height Depth 7
ページ8に含まれる内容の要旨
Step 1 Attach the Base Bracket (1) to the Lift Column (2): • Using the small Hex wrench and 6mm x 20mm screws (O), connect the base bracket to the lift column. Note that one side is counter sunk to ensure flush installation of screws. Hand tighten all four screws before proceeding. If the height of the TV to be used is greater than 22” a spacer block will be needed under the base bracket and lift column. 2 1 O x4 8
ページ9に含まれる内容の要旨
Step 2 Attach the Bayonet Bracket (3) to the enclosure: • Using the #10 x ¾” screws (Q), attach the bracket so that the top edge of the brackets back plate is 20” above the bottom mounting surface (the bottom of the cabinet or top of the spacer block if used). 3 x4 Q 9
ページ10に含まれる内容の要旨
Step 3 Secure Lift Column and Base Bracket in enclosure: • Gently glide the lift column into place on the bayonet bracket so that the tapered slots on the column are secured to the extrusions on the bracket. Gently push down until the base bracket is touching the bottom of the enclosure. DO NOT ATTACH THE BASE BRACKET TO THE MOUNTING SUREFACE AT THIS TIME! • For floating top installations it is recommended that the top of the lift column sits below the lip of the enclosure by 10mm (7/16”)
ページ11に含まれる内容の要旨
Step 4 Connect Screen Adapter (12) to the Screen Support (4): • Use the large hex wrench to secure the screen adapter to the screen support using four 3/8-16 x ¾” screws (S). Depending on TV size and mounting hole pattern the screen adapter can be vertically adjusted for optimal fit. TOP 12 4 12 4 S x4 11
ページ12に含まれる内容の要旨
Step 5 Initialize the lift system: • Connect the motor cable to the control box and “pigtail” on the lift column as shown in figures A and B. • Connect the IR receiver/control switch and control box power as shown in figures C and D. • Once all the cables are properly connected, the lift must be initialized by pressing and holding the down button on the IR receiver until the column is at its lowest limit (see figure E for IR receiver orientation). There will be slight raising and lowering
ページ13に含まれる内容の要旨
Step 6 Attach the Screen Support(4) and Top Plate(5) to the Lift Column(2): • Before attaching the top plate ensure that the rubber guide on the “pigtail” is secured in the square cutout on what will be the front of the lift column (fig. A). Failure to do so may result in damage to the wire. • Once the pigtail is secure, line up the holes on top of the screen support with the holes in the lift column. Make sure the plate is on the same side as the pigtail, the pigtail will be protected by
ページ14に含まれる内容の要旨
Step 7 Attach lift assembly to enclosure base: • Using a level on the top plate ensure that the lift column and assembly are level within the enclosure. Gently tap the base of the column left or right to bring the top plate level. • Using four #10 x ¾” (Q) screws attach the base bracket and lift assembly to the enclosure. 2 1 Q x4 14
ページ15に含まれる内容の要旨
Step 8 Attach the Universal Adapter to the TV: • Place the TV face down on a protected surface. • For larger TV’s, the vertical rails may need swapped out for the longer included rails. Rails are swapped by removing 2 Phillips screws per rail. • Use the self center function of the adapter to line up the TV’s mounting holes with the slots in the vertical rails. Connect the TV to the adapter using the correct screws (M-A – M-L) and square washers (U). Spacers (M-M and M-N) may be needed if t
ページ16に含まれる内容の要旨
Step 9 Connect the TV and universal adapter to the lift column: • Partially install two ¼-20 x ½” (W) hex screws into the top rear of the universal adapter (fig. A). • Lift and lock TV into position on screen adapter (fig. B). • Install two remaining hex screws through the screen adapter into the universal adapter. Hand tighten all 4 hex screws to secure TV to the lift column (fig. C). Figure A Figure B Figure C 16
ページ17に含まれる内容の要旨
Step 10 Install universal adapter rail covers: • Carefully attach the correct plastic covers to the universal adapter. 17
ページ18に含まれる内容の要旨
Appendix Using guide pins for a floating top: • The guide pins are recommended for use as a safety measure to prevent pinch points. A template has been included to assist with guide pin use. • If the guide pins are to be used, make sure the top surface of the enclosure will not be used as a load bearing surface. • Carefully consider the location of the top plate and guide pins in relation to the center of the enclosure lid before construction of the enclosure. The top plate and guide pins
ページ19に含まれる内容の要旨
Guide Pin/Top Plate Template 19
ページ20に含まれる内容の要旨
OmniMount Systems, Inc. 8201 South 48th Street Phoenix, AZ 85044-5355 1-800-MOUNT-IT 1-800-668-6848 www.omnimountpro.com Thank you for purchasing an OmniMount product. 20
