ページ1に含まれる内容の要旨
Parallel to Serial and
Serial to Parallel Converter CE
Model 232SPS2
Documentation Number 232SPS2-3903m
This product designed and manufactured in Ottawa, Illinois USA
of domestic and imported parts by
International Headquarters
B&B Electronics Mfg. Co. Inc.
707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
Home Page: www.bb-elec.com
Sales e-mail: orders@bb-elec.com -- Fax (815) 433-5109
Technic
ページ2に含まれる内容の要旨
Table of Contents CHAPTER 1: INTRODUCTION .......................................................1 PACKING LIST.................................................................................1 SPECIFICATIONS ............................................................................2 CHAPTER 2: PARALLEL TO SERIAL INSTALLATION ..............3 CONNECTING THE 232SPS2 TO YOUR PARALLEL PORT........3 CONNECTING THE 232SPS2 TO YOUR SERIAL PRINTER........3 CHAPTER 3: SERIAL TO PARALLEL INS
ページ3に含まれる内容の要旨
SPECIFICATIONS CHAPTER 1: INTRODUCTION Size: 3.8L x 2.4W x 0.9H in The 232SPS2 is a bi-directional parallel to serial converter. The Buffer Size: 96 bytes 232SPS2 allows you to convert data from your parallel port to a Data Formats: serial communication format or to convert data from your serial port to a parallel communication format. Standard baud rates from 1200 Baud Rates: 1200 to 115.2k baud to 115.2k with a variety of data formats can be used to match the Data Bits: 7 or
ページ4に含まれる内容の要旨
CHAPTER 2: PARALLEL TO SERIAL INSTALLATION When converting data from your parallel port to a serial communication format, position #8 of the dipswitch must be "ON". The other seven positions should be set to match the data format of your serial printer. Refer to Table 5.1 for dipswitch setting specifications. Data Flow 232PS 232SPS2 Parallel Port Serial Printer CONNECTING THE 232SPS2 TO YOUR PARALLEL PORT The 232SPS2 uses most of the available pins on the parallel port. T
ページ5に含まれる内容の要旨
CHAPTER 3: SERIAL TO PARALLEL INSTALLATION When converting data from your serial port to a parallel communication format, position #8 of the dipswitch must be "OFF". The other seven positions should be set to match the data format of your computer's serial port. Refer to Table 5.1 for dipswitch setting specifications. CONNECTING THE 232SPS2 TO YOUR PARALLEL PRINTER The 232SPS2 has a DB-25 female connector on its parallel port. Most parallel printers use a Centronics 36-pi
ページ6に含まれる内容の要旨
CHAPTER 4: POWER CONNECTIONS The unit may be port-powered using DTR and RTS on the serial port. If the 232SPS2 cannot be powered using the handshake lines, it may be powered externally using +7 to +18 volts DC at 2 milliamps. If you are using an external supply, simply plug a 2.5 mm plug from an appropriate DC source into the power jack on the side of the 232SPS2 module. Power supplies are available through B&B. (Model 232PS is recommended.) 232SPS2-3903 Manual Chapter 4: Power Connec
ページ7に含まれる内容の要旨
Table 5.1 CHAPTER 5: SELECTING DIPSWITCH SETTINGS The 232SPS2 is set up using an eight-position dipswitch. In Setting DIP SWITCH POSITION order for the 232SPS2 to function properly, it must be set up to 1 2 3 4 5 6 7 8 match your system's requirements. The following parameters on the 232SPS2 are set on the dipswitch: converter direction, baud rate, 1200 Baud OFF OFF OFF X X X X X flow control, number of data bits, and the type of parity. Each of the 2400 Baud ON OFF OFF X X X X X
ページ8に含まれる内容の要旨
Table A-2 APPENDIX A: PARALLEL PORT CONNECTIONS Serial to Parallel Mode The parallel port connections for the parallel to serial and serial DB-25 Signal Name 232SPS2 to parallel mode are shown in Table A-1, and Table A-2, Pin # Direction respectively. The connections required are the same for both modes 1 Strobe Output of handshaking. The error lines on the parallel port are forced to the 2 Data bit #0 Output "no error" states. If the printer is off-line, out of paper, etc., the
ページ9に含まれる内容の要旨
SERIAL TO PARALLEL MODE, SOFTWARE HANDSHAKING APPENDIX B: SERIAL PORT CONNECTIONS For proper operation the following connections must be present: The next four sections will cover the required serial port 1. Transmit Data (TD) from the host (DTE) must be connections on the 232SPS2. Each section will list the required connected to Pin #2 on the 232SPS2 module. connections and the optional connections that some systems may 2. Receive Data (RD) from the host (DTE) must be requir
ページ10に含まれる内容の要旨
TABLE B-1 PARALLEL TO SERIAL MODE, HARDWARE HANDSHAKING DB-25 Serial Port Connections (S to P) The serial port of the 232SPS2 module is wired as a DCE Serial Port 232SPS2 device. For proper operation the following connections must be (DTE) Signal Name Direction (DCE) present: DB-25S Pin # DB-25P Pin# 1. Transmit Data (TD) from the printer (DTE) must be 2 Transmit Data -----------> 2 connected to Pin #2 on the 232SPS2 module. 3 Receive Data <----------- 3 2. Data Set Ready (DSR
ページ11に含まれる内容の要旨
Some printers may require one or more of the following connections: TABLE B-4 6. Data Set Ready (DSR) from the printer must be DB-9 Serial Port Connections (P to S) connected to Pin #6 on the 232SPS2 module. Serial Port 232SPS2 7. Clear To Send (CTS) from the printer should be (DTE) (DCE) connected to Pin #5 on the 232SPS2 module. DB-9S Signal Name Direction DB-25P 8. Data Carrier Detect (DCD) from the printer should Pin # Pin # be connected to Pin #8 on the 232SPS2 module. 1
ページ12に含まれる内容の要旨
APPENDIX C: SOFTWARE HINTS MODE COM1: 96,n,8,1,p If any of the parameters are omitted, the most recent setting will be used. It is recommended that the "p" option be used for the retry PARALLEL TO SERIAL MODE option. If the "p" is not used, a device busy error may occur. To In parallel to serial mode, data from the computer is output send data out the serial port, the following command can be entered through the parallel port. The 232SPS2 will send the data to the at the DOS
ページ13に含まれる内容の要旨
APPENDIX D: TROUBLESHOOTING Symptom Possible problem Solution No data is being Printer is off-line Put printer on-line printed. Printer is out of paper Fill printer with paper Improper dipswitch Check settings settings (Table 5.1) Improper mode selected Wrong type of flow control Serial port settings do Set serial ports to not match match (Table 5.1, Appendix C) No or not enough Check power on power to 232SPS2 232SPS2 (Ch. 4) Improper connections Check connections
ページ14に含まれる内容の要旨
APPENDIX E: Declaration of Conformity DECLARATION OF CONFORMITY Manufacturer’s Name: B&B Electronics Manufacturing Company Manufacturer’s Address: P.O. Box 1040 707 Dayton Road Ottawa, IL 61350 USA Model Number: 232SPS2 Description: Parallel to Serial Converter Type: Light industrial ITE equipment Application of Council Directive: 89/336/EEC Standards: EN 55022 EN 61000-6-1 EN 61000 (-4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11) William H. Franklin III, Director of Engineer
