ページ1に含まれる内容の要旨
SERIAL NUMBERS
Prefix and Above
HEWLETT
PACKARD
HP Part No. 08560-90081
August 1992
Printed in USA
Eiia
3207A
Analyzer Spectrum 8560A HP
Manual Service
ページ2に含まれる内容の要旨
@Copyright Hewlett-Packard Company 1990, 1992 All Rights Reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. 1212 Valley House Drive, Rohnert Park, CA 94928-4999, USA
ページ3に含まれる内容の要旨
Certification Hewlett-Packard Company certifies that this product met its published specifications at the time of shipment from the factory. Hewlett-Packard further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, to the extent allowed by the Institute’s calibration facility, and to the calibration facilities of other International Standards Organization members. Warranty This Hewlett-Packard instrument product is warr
ページ4に含まれる内容の要旨
The following safety symbols are used throughout this manual. Familiarize yourself with each of the symbols and its meaning before operating this instrument. The caution sign denotes a hazard. It calls attention to a procedure which, if not correctly performed or adhered to, could result in damage to or destruction of the instrument. Do not proceed beyond a caution sign until the indicated conditions are fully understood and met. The warning sign denotes a hazard. It calls attention to a procedu
ページ5に含まれる内容の要旨
HP 8560A Spectrum Analyzer Documentation Outline For ordering information, contact a Hewlett-Packard Sales and Service Office. Manuals Shipped with Your Instrument HP 8560A Installation and Verification Manual n Tells you how to install the spectrum analyzer. n Tells you what your analyzer’s specifications are. 0 perating and Programming Manual HP 856OA/8561 B/8563A w Tells you how to make measurements with your spectrum analyzer. w Tells you how to program your spectrum analyzer. HP 8560A Quick
ページ6に含まれる内容の要旨
Contents 1. General Information l-l ......................... Manual Organization l-2 ....................... Manual Text Conventions l-2 ................. Serial Numbers Covered by This Manual l-3 ......................... Instrument Variations l-6 ................ HP 85629B Test and Adjustment Module .............................. l-6 Service Kit ..................... 1-6 Recommended Test Equipment l-7 ........................ Electrostatic Discharge l-7 ................. Reducing Potential fo
ページ7に含まれる内容の要旨
15. External Mixer Amplitude Adjustment .............. 2-57 16. Second IF Gain Adjustment .................. 2-60 17. Signal ID Oscillator Adjustment ................. 2-63 18. 600 MHz Amplitude Adjustment ................ 2-66 19. 10 MHz Reference Adjustment (Option 003) ........... 2-68 20. Tracking Oscillator Adjustment (Option 002) ........... 2-71 3. Assembly Replacement Access to Internal Assemblies 3-2 ...................... Cable Color Code ........................... 3-2 Procedure 1. An
ページ8に含まれる内容の要旨
6. General Troubleshooting Introduction ............................. 6-1 Assembly Level Text ........................ 6-l Block Diagrams ........................... 6-l ........................ Assembly Test Points 6-2 Pad.. ............................. 6-2 Test Jack ............................ 6-2 Ribbon Cables ........................... 6-2 ................. 6-6 WR PROT/WR Menus ................. 6-8 Troubleshooting to a Functional Section Using the TAM ............................ 6-10
ページ9に含まれる内容の要旨
Option Module Errors (800 to 899) .................. 6-34 .................. 6-34 User-Generated Errors (902 to 904) ....................... 6-35 Block Diagram Description RF Section ............................. 6-36 A7 LODA ............................ 6-36 A8 Low Band Mixer ........................ 6-36 ....................... 6-36 A9 Input Attenuator 6-36 All YTO ............................ ....................... 6-37 Al3 Second Converter .......... 6-37 Second IF Distribution Amplifier (
ページ10に含まれる内容の要旨
........................... 7-21 Track and Hold ...................... 7-22 A3 Assembly’s ADC Circuits ........................ 7-22 ADC Control Signals ....................... 7-23 ADC Start/Stop Control ............................. 7-24 ADC ASM 7-24 ADC ............................... ........................... 7-25 Ramp Counter ..................... 7-26 A3 Assembly’s Control Circuits Analog Bus Drivers ......................... 7-26 ......................... 7-27 Analog Bus Timing ........
ページ11に含まれる内容の要旨
.................. 8-34 A4 Assembly’s Cal Oscillator Circuit ............ Cal Oscillator Unlock at Beginning of IF Adjust 8-35 Inadequate CAL OSC AMPTD Range ................. 8-35 ....... 8-36 300 Hz to 3 Resolution Bandwidth Out of Specification 8-40 Low-Pass Filter ........................... Sweep Generator .......................... 8-40 .......... AM/FM Demodulation, Audio Amplifier, and Speaker 8-40 9. Controller Section Troubleshooting Using the TAM .................... 9-l Blank Displa
ページ12に含まれる内容の要旨
Unlocked Reference PLL ........................ Operation ............................. Troubleshooting .......................... Third LO Driver Amplifier ...................... 10-44 Sampler and Sampler IF ........................ 10-45 Sweep Generator Circuit ........................ 10-47 A21 OCXO (Option 003 only) ..................... 11. RF Section Troubleshooting Using the TAM .................... 11-2 ................. Low Band Problems (50 Hz to 2.9 GHz) 11-4 Low Band Problems .......
ページ13に含まれる内容の要旨
12. Display/Power Supply Section .................... 12-4 Troubleshooting Using the TAM 12-5 Blank Display ........................... 12-6 Blank Display ............................ 12-7 Display Distortion .......................... 12-8 ............................ Focus Problems 12-9 .......................... Intensity Problems 12-11 ...................... A6 Power Supply Assembly 12-11 ......................... Dead Power Supply 12-13 ......................... Line Fuse Blowing 12-13 .....
ページ14に含まれる内容の要旨
Figures l-2 .................... l-1. Serial Number Label Example 1-7 ................. l-2. Example of a Static-Safe Workstation ......... l-10 1-3. HP 8560A Shipping Container and Cushioning Materials ............. 2-12 2-1. High-Voltage Power Supply Adjustment Setup ...................... 2-14 2-2. Display Adjustment Setup 2-17 ........................ 2-3. CRT Adjust Pattern 2-18 ................... 2-4. A2 Display Adjustment Locations 2-20 .................... 2-5. IF Adjustment Setup ....
ページ15に含まれる内容の要旨
3-27 3-15. RF Section Bias Connections . . . . . . . . . . . . . . . . . . . . . ................. 3-16. A9 Mounting Screws at Right Frame 3-30 ............... 3-31 3-17. A10 Tracking Generator Mounting Screws ........................ 3-32 3-18. All Mounting Screws ................... 3-34 3-19. Al4 and Al5 Assembly Removal .................... 3-36 3-20. Al4 and Al5 Assembly Cables 3-37 3-21. Al7 Mounting Screws ........................ 3-41 3-22. Main Deck Screws ......................... 3-43
ページ16に含まれる内容の要旨
8-31 ........................ 8-13. Faulty Crystal Short 8-31 ........................... 8-14. Faulty LC Pole 8-33 ...................... 8-15. Faulty Crystal Symmetry ............ 8-37 8-16. Output Waveform, 10 Resolution Bandwidth ............ 8-38 8-17. Output Waveform, 3 Resolution Bandwidth 8-38 ............ 8-18. Output Waveform, 1 Resolution Bandwidth ............ 8-39 8-19. Output Waveform, 300 Hz Resolution Bandwidth 8-39 ..................... 8-20. Failed Crystal Set Symptoms 8-43
ページ17に含まれる内容の要旨
Tables l-l. Service Kit Contents ........................ l-6 l-2. Static-Safe Accessories ........................ l-8 l-3. Hewlett-Packard Sales and Service Offices ............... 1-12 1-4. Recommended Test Equipment .................... 1-13 2-l. Related Adjustments (1 of 2) ..................... 2-4 ..................... 2-5 2-l. Related Adjustments (2 of 2) ................... 2-6 2-2. Adjustable Components (1 of 3) ................... 2-2. Adjustable Components (2 of 3) 2-7 ..............
ページ18に含まれる内容の要旨
................... 8-12 8-4. Available Reference Level Range 8-12 ................ 8-5. Signal Level for Reference Level Display 9-2 9-l. TAM Tests Versus Test Connectors .................. ............................ 9-2. Gate Times 10-3 10-l. Center Frequency Tuning Values ................... ................. 10-7 10-2. Sampling Oscillator Test Frequencies 10-3. YTO Frequency in TEST Position .................. 10-9 .............. 10-4. Automatic Fault Isolation References (1 of 2) ........
ページ19に含まれる内容の要旨
General Information This HP 8560A Spectrum Analyzer Service Manual contains information required to adjust and service the HP 8560A Spectrum Analyzer to the assembly level. For component-level information, refer to the HP 856OA/61B/63A Spectrum Analyzer Component Level Information. Manual Organization Chapter 1, General Information, contains information about service kit contents, recommended test equipment, returning an instrument for service, and sales and service offices. Chapter 2, Adjustmen
ページ20に含まれる内容の要旨
Manual Text Conventions The following text conventions are used throughout this manual: Boxed text in this typeface represents a mechanical key physically located on the m instrument. Sof tkeys Shaded text indicates a labels appear on the display and can be activated by pressing corresponding keys surrounding the display. The labels displayed are determined by the mechanical front-panel key depressed and the instrument’s firmware. Display Text printed in this typeface indicates text appearing
