ページ1に含まれる内容の要旨
®
Extender for
®
HDMI 1.3 over
One Fiber with IR
EXT-HDMI1.3-1FO
User Manual
www.gefen.com
ページ2に含まれる内容の要旨
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday Pacifi c Time Write To: Gefen, LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen, LLC reserves the right to make changes in the hard ware, packaging and any accompanying doc u men ta tion without prior written notice. HDMI, the HDMI Logo, and High-Defi nition Multimedia I
ページ3に含まれる内容の要旨
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Unit Layout 5 Sender Unit Descriptions 6 Receiver Unit Layout 7 Receiver Unit Descriptions 8 Connecting and Operating the Extender 9 DIP Switch Confi guration 10 DIP Switches 11 Local EDID / External (Pass-Through) EDID Modes 11 Deep Color 11 Calibration Procedure 12 Specifi cations 13 Warranty
ページ4に含まれる内容の要旨
INTRODUCTION Congratulations on your purchase of the Extender for HDMI 1.3 Over One Fiber with IR. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies. Gefen’s reliable, plug-and-play products supplement cross-platform computer systems, professional audio/video environments and HDTV systems of all sizes with hard-working solutio
ページ5に含まれる内容の要旨
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE EXTENDER FOR HDMI 1.3 OVER ONE FIBER WITH IR • IR data repeater functionality is single-directional. IR data can only be transmitted from the Receiving unit back to the Sending unit. IR data cannot be transmitted from the Sending unit to the Receiving unit. • Use one SC-terminated multi-mode fi ber optic cable to operate the HDMI 1.3 Over One Fiber with IR. • 1080p video may be extended up to 1000 feet (300m), depending on th
ページ6に含まれる内容の要旨
FEATURES HDMI 1.3 Features • 225 MHz (up to 12 bit YUV 444 @ 1080p) • Deep Color • Dolby TrueHD and DTS-HD Master Audio • Lip-Sync • CEC Protocol Pass-Through Features • Supports video resolutions up to 1080p,1920 x 1200 and 2K • 3DTV Pass-Through • Delivers highest quality signal of any HDMI extension method • EDID Detection/Adjustment for rapid integration of source and displays • Extends HDMI and RS-232 up to 1000 feet (300m) • Uses widely available single-strand multi-mode SC fi ber optic cab
ページ7に含まれる内容の要旨
SENDER UNIT LAYOUT Front 45 12 3 Back 67 4
ページ8に含まれる内容の要旨
SENDER UNIT DESCRIPTIONS 1 Power Indicator This two-color LED will turn bright red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supply has been connected to an available wall outlet. This LED will turn bright green once the Sender unit and Receiver unit are communicating correctly. 2 Calibration Indicator This LED will alternate from red to green during the calibration procedure. The LED will turn solid green once the calibratio
ページ9に含まれる内容の要旨
RECEIVER UNIT LAYOUT Front 12 345 Back 67 8 6
ページ10に含まれる内容の要旨
RECEIVER UNIT DESCRIPTIONS 1 RS-232 Output Port Connect a controlling device to this port. 2 Locking HDMI Output Port Connect a HDTV display to this HDMI port 3 IR Window Receives signals from the Hi-Def source IR remote control unit. The IR signals are sent back to the source device, when using an IR Blaster. 4 Calibration Indicator This LED will alternate from red to green during the calibration procedure. The LED will turn solid green once the calibration procedure has been completed.
ページ11に含まれる内容の要旨
CONNECTING AND OPERATING THE GEFEN EXTENDER FOR HDMI 1.3 OVER ONE FIBER WITH IR How to Connect the Extender for HDMI 1.3 over One Fiber with IR 1. Connect a Hi-Def source to the Sender Unit using the included Locking HDMI cable. Connect the HDTV display to the Receiver Unit with a user-supplied HDMI cable. 2. Connect an SC-terminated fi ber optic cable to the Sender Unit. Connect the opposite end of the fi ber cable to the Receiver Unit. 3. OPTIONAL: Connect an RS-232 cable from the RS-232 s
ページ12に含まれる内容の要旨
DIP SWITCH CONFIGURATION DIP Switches On the bottom of the Sender Unit and Receiver Unit are a bank of four (4) DIP switches. These DIP switches provide control over EDID, Deep Color, and unit Calibration. Remove the strip of tape to expose the DIP switches. To change the DIP switch settings, move the appropriate DIP switch to its ON or OFF position using a small pointed object. The DIP switches and their functions are shown below. Sender Unit DIP switches DIP Switch Function 1 EDID Mode:
ページ13に含まれる内容の要旨
DIP SWITCH CONFIGURATION DIP 1 - EDID Mode • OFF - Local EDID When Local EDID mode is used, the EDID will be assembled by copying all video and audio features of the connected device. Deep Color support will be manually controlled: If Deep Color is supported by the display(s), DIP 2 should be set to the ON position (see DIP 2 - Deep Color, below). By default, the unit is shipped with DIP 1 in the OFF position. • ON - Pass-Through EDID Allows all video and audio features of the connected d
ページ14に含まれる内容の要旨
DIP SWITCH CONFIGURATION Calibrating the Sender Unit and Receiver Unit IMPORTANT: Before beginning the calibration process, make sure that the Sender Unit and Receiver are not powered. 1. Make sure DIP switch 3 on both the Sender Unit and the Receiver Unit are in the OFF position (see page 9). 2. Connect one end of the fi ber cable to the Sender Unit. Connect the other end of the fi ber cable to the Receiver Unit. 3. Make sure DIP switch 3 on both the Sender Unit and the Receiver Unit are in
ページ15に含まれる内容の要旨
SPECIFICATIONS Video Amplifi er Bandwidth ........................................................................ 225 MHz Maximum Resolutions Supported: ..................................1080p60, 1920x1200, 2K Input Video Signal .............................................................................. 1.2 Volts p-p Input DDC Signal .......................................................................... 5 Volts p-p (TTL) HDMI Input/Output Connector ........................................
ページ16に含まれる内容の要旨
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notifi ed within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifi cations. Equipment that fails under conditions other than those covered will be repaired at the current price of
ページ17に含まれる内容の要旨
Rev A5 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Pb This product uses UL listed power supplies.
