ページ1に含まれる内容の要旨
®
WINEGARD
TM
Movin’ View
Digital Satellite Mobile Antenna for Two Receivers
for Use While Stationary or In-Motion
Model MV-4002
Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. © Winegard Company 2005 2452062 Rev. 5/05
1
ページ2に含まれる内容の要旨
Introduction/How Does Digital Satellite TV Work? About this manual —We hope this manual will provide clear instructions to install and operate MV-4002. Two symbols have been used — Indicates suggestions to make Indicates caution should be taken! ! processes easier for you. Introduction For Programming information call: Congratulations! You have purchased one of ® DISH NETWORK - 1-800-333-DISH (1-800-333-3474) Winegard’s latest developments in the mobile satellite TM ® reception product line —the
ページ3に含まれる内容の要旨
FRONT OF VEHICLE FRONT OF VEHICLE Quick Reference Guide NOTICE! ® This model is PRESET for DIRECTV receivers. ® ® If you have a DISH Network or ExpressVu (Canada) receiver, you must change the numbered switches inside the dome. TO CHANGE SWITCHES INSIDE DOME — 1. Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage. ® Switches will be set at 101° for DIRECTV . You will be changing these switches. Models MV-4002, MV-4000, MV-4005 MOUNTING (#1 represents
ページ4に含まれる内容の要旨
Operation b. If it moves off the signal , it is in an effort to verify 1. Turn on receiver and television set. The MV-4002 the signal and it should return to the signal shortly. must be connected to a receiver that is plugged into 120 VAC. 5. After the unit has verified that it has the correct satellite, it will continue to fine tune for about 6 min- 2. Verify that you are getting the receiver’s menu utes (unless the vehicle is in-motion, see 7 below). screens on the television. These screens ar
ページ5に含まれる内容の要旨
To toggle between satellites when subscribing to multi-satellite programming— While in Sleep Mode, the MV-4002 will toggle be- If a switch other than SW42 appears, or you tween the primary and seconday satellites for either have an X in one of the boxes below the satel- DISH Network or DIRECTV. Both have program- lites, repeat Check Switch Steps. ming on more than one satelite.When a channel is selected on the remote control and is not on the 5. Your system is now set up to toggle between sa
ページ6に含まれる内容の要旨
Parts Included • Tools Needed • How to Unpack PARTS INCLUDED: 1 Radome 1 large yellow spade connector 1 Power switch 2 small red spade connectors 1 Wall plate (white) All required screws and washers 1 Surface mount box 1 base with electronics, dish, single LNBF 1 Cable entry plate 30’ power cable and 30’ coaxial cable TOOLS NEEDED FOR UNPACKING & INSTALLATION: Level Phillips screw driver #2 Drill w/3/4” bit Sealant (consult RV manufacturer for proper type 1-1/4” hole saw (if mounting switch in w
ページ7に含まれる内容の要旨
Base Diagram SWITCH LOCATION FIGURE 2 (SIDE OF BOX, SEE PAGE 3) CONTROL COAX CABLE AT BOX TO LNBF CONTROL BOX EL MOTOR GPS ANTENNA CABLE +12VDC POWER CABLE GPS ANTENNA CENTER LINE OF THE VEHICLE CONTROL BOX (DETAIL BELOW) FOOT MUST BE PARALLEL TO THE CENTER LINE OF THE AZ MOTOR VEHICLE LNBF VOLTAGE REFLECTOR CONTROL BOX DETAIL ELECTRONICS INTERIOR VIEW Vehicle Front (#1 represents Switch DOWN; #0 represents Switch up) A Sat. Rcvr. Mt. Option Switch Set Position Mount ..
ページ8に含まれる内容の要旨
Installation Installing unit on roof of vehicle — Install in DRY conditions only! 6. Place the unit on the roof in its permanent loca- ! tion and mark around the base bracket, Figure 4. IMPORTANT! Do not install this system (Make sure the rear adjustable base foot is par- in the rain, or under any wet conditions. Mois- allel with the center line of the vehicle. Refer ture may affect electronics and void your to page 3, Figure 1A ). warranty! 1. For best performance and to reduce signal ac- 7. Cl
ページ9に含まれる内容の要旨
Installation GPS installation — INSTALLING THE POWER SWITCH 10. The GPS antenna is pre-wired and has a 1 meter 1. Choose a location to install the MV-4002 power cable running through one of the connectors. ON/OFF switch. Remember when selecting a location that you will need to run the +12VDC power cable from Determine location for GPS antenna. It is recom- the MV-4002 to the switch. Be sure the switch is in mended you place the GPS antenna 3 feet from dome. the OFF position before continuing. S
ページ10に含まれる内容の要旨
Installation • Wiring Connecting the receiver — WIRING TWO RECEIVERS MV-4002 Tracking System NOT USED Connecting one receiver 1. Mount the DC Passive D575p demultiplexer in the INPUT same cabinet as your receiver. D575p DEMULTIPLEXER 2. Connect the coax cable from the roof to the “input” on SAT RECEIVER the DC Passive D575p demultiplexer. Connect a coax cable from the “sat receiver” on the DC Passive SATELLITE IN demultiplexer. Connect other end of this cable to “satel- PRIMARY RECEIVER lite i
ページ11に含まれる内容の要旨
Troubleshooting SOLUTION PROBLEM 1. Check your Power switch to verify that it is in the ON position. The MV-4002 does not attempt to find a satellite or it never moves. 2. Make sure that the receiver is plugged in and the satellite in jack is connected to MV-4002. 3. Verify that the MV-4002 has had it’s three shipping straps re- moved. These straps are located inside the dome and keeps the dish from moving until it is installed. 1. Wait 10 minutes. The unit can take up to 10 minutes to acquire T
ページ12に含まれる内容の要旨
Specifications & Warranty Features and specifications • One button operation. • 30’ power cable and 30’ coaxial cable included. • GPS satellite signal acquisition. • Dome UV protected. • Depending on receiver type, you can access • Off-white color compatible with all vehicles. satellites 119°, 110°, 101° or 92°. • Compact size — • No user input required. 32” diameter, 15.75” height Weight of unit - 32 lbs. TM • No data port required for DISH Network , Shipping weight - 44 lbs. ® DIRECTV or
