ページ1に含まれる内容の要旨
848-D3N-93A1 (704)
OWNER’S MANUAL
HEDGE-TRIMMERS
eHT753S
eHT603D
• Before using our products,
please read this manual
carefully to understand the
CAUTION
proper use of your unit.
• Keep this manual handy.
ページ2に含まれる内容の要旨
English SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■NOTES ON TYPES OF WARNINGS IN THE MANUAL WARNING This mark indicates instructions which must be followed in order to prevent accidents which could lead to serious bodily injury or death. IM
ページ3に含まれる内容の要旨
English 1. PARTS LOCATION 1. Plate receive 2. Right handle 3. Starter 4. Fuel cap 5. Left handle 6. Engine Stop switch 7. Throttle lever 8. Fuel tank 9. Muffler 10. Blade 11. Air cleaner 12. Spark plug 13. Gear case 14. Throttle cable 15. Choke lever 16. Front handle 17. Engine switch 18. Safty lock lever 19. Rear handle 20. Lock lever 21. Grease nipple 3
ページ4に含まれる内容の要旨
English WARNING 1. CLEANER Please inspect the cleaner every day for dirt. Please clean out any dust that is found up to the element on the carburetor side. When rebuilding the cleaner, be sure to follow the following order: element → felt → element. If dust remains on the cleaner when it is used, the dust may enter the engine, cause abrasion in the pistons, and lead to engine damage. 2. GEAR CASE Please re-supply the gear case with grease every 25 hours. Grease must be added every day if the uni
ページ5に含まれる内容の要旨
English 3. SAFETY PRECAUTIONS ■ BEFORE USING THE MACHINE a.Read this owner's manual carefully to understand how to operate this unit properly. b. This product has been designed for use in trimming leaves and branches from trees and hedges, and it should never be used for any other purpose since doing so could result in unforeseen accidents and injuries occurring. c. You should never use this hedge- trimmer when under the influence of alcohol, when suffering from exhaustion or lack of sleep, when
ページ6に含まれる内容の要旨
English 3. SAFETY PRECAUTIONS g. Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury. Limit the amount of time over which the hedge-trimmer is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes of rest between work sessions. Also try to keep the total amount of work performed in a single day under 2 hours or less. h. Be sure to keep this manual handy so that you may refer to
ページ7に含まれる内容の要旨
English 3. SAFETY PRECAUTIONS ■WARNING CONSIDERING HANDLING OF FUEL a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. You should never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. b. Smoking while operating the hedge-trimmer or refilling its fuel tank is extremely dangerous. Always be sur
ページ8に含まれる内容の要旨
English 3. SAFETY PRECAUTIONS persons, always check the presence and locations of others so as to maintain a distance each person sufficient to ensure safety. c. Make sure that there are no loose screws or bolts, fuel leaks, ruptures, dents, or any other problems which might interfere with safe operation. Be especially careful to check that there is nothing wrong with the blades or with the joints by which the blades are attached to the hedge- trimmer. d. Never use blades that are bent, warped,
ページ9に含まれる内容の要旨
English 3. SAFETY PRECAUTIONS ■ KICKBACK SAFETY PRECAUTIONS •A dangerous reaction may occur when the spinning blade contacts a solid object in the critical area. It is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury. Avoid kickback, observe the safety precautions below strictly. 1. Keep the cutting blades clear of fances, posts, wires, and rocks to prevent kickback and damage to the blades. 2. When using your hedge-trimmer, do not
ページ10に含まれる内容の要旨
English 3. SAFETY PRECAUTIONS d. If the grass gets caught in the blade during operation, or if you need to check the unit or refuel the tank, always be sure to turn off the engine. e. If the blade touches a hard object like a stone, immediately stop the engine and check if something is wrong with the blade. If so, replace the blade by new one. f. If someone calls out while working ,always be sure to turn off the engine before turning around. g. Never touch the spark plug or plug cord while the e
ページ11に含まれる内容の要旨
English 3. SAFETY PRECAUTIONS d. When sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury. e. When replacing blade or any other parts or when replacing the oil or any lubricants, always be sure to use only ZENOAH products or products which have been certified by ZENOAH for use with the hedge-trimmer. 11
ページ12に含まれる内容の要旨
English 4. FUEL WARNING •Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. •Make sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored. IMPORTANT •Never use oil for 4 cycle engine use or water cooled 2-cycle engine. • Never use "FUEL WITH NO OIL (RAW GASOLINE)". • Never use fuel laced with water. • Mixed fuels which have been le
ページ13に含まれる内容の要旨
English 5. OPERATION ■ STARTING THE ENGINE F1 WARNING Keep the blades clear of everything around It as they will start moving upon the engine starts. 1. [eHT753S] Make sure that the throttle lever is at idling position. [eHT603D] Release the throttle lever and make sure it is fully back. (F1) 2. [eHT603D] Set the engine switch to the “I (RUN)” position. (F1) 3. Push the primer pump until overflown fuel flows out in the clear tube. (F2) 4. Move the choke lever to the closed position. (F3) F2 (1)
ページ14に含まれる内容の要旨
English 5. OPERATION ■ CUTTING WORK WARNING •Weather conditions and altitude may effect carburation. • Do not allow anyone to stay close to the hedge-trimmer while working or while adjusting the carburetor. ■ HOW TO USE HANDLE [eHT603D only] (F5) F5 [eHT603D] To reduce fatigue when trimming hedges, the handle can be swivelled through 90° to the left or right. Do not press the throttle during this operation! Proceed as follows: 1. Free the handle by pressing the locking lever. 2. Turn the handle
ページ15に含まれる内容の要旨
English 6. MAINTENANCE WARNING Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool. F8 ■ BLADE (F8) • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. Point: 1. Keep the end corner sharp. 2. Round the root of the edge. 3. Do not use water when using a F9 grinder. ■ ADJUSTING THE BLADE GAPS (F9) To adjust the blade gaps, proceed as follows. 1. Fully tighten the blade-sec
ページ16に含まれる内容の要旨
English 6. MAINTENANCE 3. Check if the safety lock returns to its original position when you release your hand from safety lock. If you find any defects at the checks above, contact your nearest servicing dealer for repair. F11 ■ ANTI-VIBRATION SYSTEM (F11) WARNING The deformed or damaged anti- vibration system may cause of the breakages like getting rickety or falling off of engine and/or blade. • [eHT753S] Check periodically if the rubber cushions are not deformed or damaged. • [eHT603D] Chec
ページ17に含まれる内容の要旨
English 6. MAINTENANCE ■ FUEL FILTER (F13) F13 When the engine runs short of fuel supply, check the fuel strainer for blockage. ■ WAY OF THE COOLING AIR F14 (F14) This engine is air-cooled. Dust clogging between the inlet port of the cooling air and cylinder fins will cause overheating of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover. ■ SPARK PLUG (F15) Starting failure and mis-firing are often caused by a fouled spark plug. Per
ページ18に含まれる内容の要旨
English 6. MAINTENANCE ■ GEARCASE (F16) F16 Supply multi-purpose grease at every 20 hours of use. 1. Use a grease pump. 2. Feed grease until it comes out of the base of blades.(F16-a) ■ ADJUSTING CARBURETOR F17 (F17) The carburetor has been adjusted at the factory. Should your unit need readjustment due to the changes in altitude or operating conditions, please let your skillful dealer make the adjustment. A wrong adjustment may cause damage to your unit. (1) Idle adjusting screw (2) Up (3) Dow
ページ19に含まれる内容の要旨
English 6. MAINTENANCE ■ MUFFLER AFTER 100 HOURS OF USE F19 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. (F19) (1) screw driver (2) muffler 2. Tighten all screws, bolts, and fittings. 3. Check to see if any oil or grease has worked its way in between the clutch lining and drum, and if it has wipe it away using oil-free, lead-free gasoline. ■MAINTENANCE BEFORE STORAGE F20 IM
ページ20に含まれる内容の要旨
English 7. SPECIFICATIONS Model name .................. eHT753S [eHT603D] Type .......Single blade [Double-blade], double-action type Blade length .............................. 750 [600]mm Engine model ........................... Zenoah G20LH Displacement ......................................... 21.7cc Carburetor .......................... Diaphragm type Ignition system ........................................... C.D.I Spark plug ......................... Champion CJ6Y Fuel ..................
