ページ1に含まれる内容の要旨
FRANÇAIS
ENGLISH ESPAÑOL
R Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
TWIST--N--EDGEt
TE500CXL
ForOccasionalUseOnly
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de inst
ページ2に含まれる内容の要旨
SAFETY RULES S Always wear foot protection. Do not go barefoot or wear sandals. Stay clear of WARNING: When using gardening spinning line. appliances, basic safety precautions must al- S Secure hair above shoulder length. Secure ways be followed to reduce the risk of fire and or remove loose clothing or clothing with serious injury. Read and follow all instruc- loosely hanging ties, straps, tassels, etc. tions. They can be caught in moving parts. This power unit can be dangerous! Operator is S B
ページ3に含まれる内容の要旨
SAFETY NOTICE: Exposure to vibrations CUTTING SAFETY through prolonged use of gasoline powered hand tools could cause blood vessel or nerve WARNING: Inspect the area before damage in the fingers, hands, and joints of each use. Remove objects (rocks, broken people prone to circulation disorders or ab- glass, nails, wire, etc.) which can be thrown normal swellings. Prolonged use in cold by or become entangled in line. Hard objects weather has been linked to blood vessel dam- can damage the trimmer
ページ4に含まれる内容の要旨
1. Remove wing nut from shield. 2. Insert bracket into slot as shown. Bracket 3. Pivot shield until bolt passes through hole Slot in bracket. Wing Nut 4. Securely tighten wing nut onto bolt. Gearbox Shield OPERATION KNOW YOUR TRIMMER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Assist Handle Trimmer Head Tu
ページ5に含まれる内容の要旨
To avoid engine problems, empty the fuel sys- 8. Pull starter rope sharply until engine runs, tem before storage for 30 days or longer. but no more than 6 pulls. Drain the gas tank, start the engine and let it NOTE: If the engine doesn’t start after 6 run until the fuel lines and carburetor are pulls (at the HALF CHOKE position), empty. Use fresh fuel next season. move the choke lever to the FULL Never use engine or carburetor cleaner prod- CHOKE position and press the primer ucts in the fuel ta
ページ6に含まれる内容の要旨
Do not run the engine at a higher speed than flower beds, but it also can cut the tender necessary. The cutting line will cut efficiently bark of trees or shrubs and scar fences. when the engine is run at less than full throttle. S For trimming or scalping, use less than full At lower speeds, there is less engine noise and throttle to increase line life and decrease vibration. The cutting line will last longer and will head wear, especially: be less likely to “weld” onto the spool. S During ligh
ページ7に含まれる内容の要旨
Sweeping Edging EDGING-- Adjust trimmer to the edging posi- tion (see TWIST AND EDGE section). Allow only the tip of the line to make contact. Do not force trimmer line into work area. MAINTENANCE CLEAN AIR FILTER WARNING: Disconnect the spark A dirty air filter decreases engine perform- plug before performing maintenance except ance and increases fuel consumption and for carburetor adjustments. harmful emissions. Always clean after every 5 hours of operation. CHECK FOR LOOSE 1. Clean the cover
ページ8に含まれる内容の要旨
SERVICE AND ADJUSTMENTS LINE REPLACEMENT INSTALLING SPOOL WITH LINE Pre--wound spools offer the most convenient 1. Install replacement spool. method for replacing line and ensuring opti- 2. Thread line through line guide ring. mum performance. Line through guide ring S Replacement spools are color--coded to ensure use of the correct spool with your unit. Be sure to use the same color spool as Slot the existing spool. NOTE: Always clear dirt and debris from cut- ting head components when performi
ページ9に含まれる内容の要旨
STORAGE Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits WARNING: Perform the following during storage. Add stabilizer to the gasoline steps after each use: in the fuel tank or fuel storage container. Fol- S Allow engine to cool before storing or trans- low the mix instructions found on stabilizer porting. container. Run engine at least 5 minutes after S Store unit and fuel in a well ventilated area adding stabilizer. where fuel vapors cannot reach sp
ページ10に含まれる内容の要旨
TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. REMEDY TROUBLE CAUSE Engine will not 1. ON/OFF switch in OFF 1. Move ON/OFF switch to ON. start. position. 2. Engine flooded. 2. See “Starting a Flooded Engine” in Operation Section. 3. Fuel tank empty. 3. Fill tank with correct fuel mixture. 4. Spark plug not firing. 4. Install new spark plug. 5. Fuel not reaching 5
ページ11に含まれる内容の要旨
LIMITED WARRANTY ELECTROLUX HOME PRODUCTS, INC., er predelivery setup or normal adjustments warrants to the original purchaser that each explained in the instruction manual. new Weed Eater" " " " brand gasoline tool or at- THIS WARRANTY GIVES YOU SPECIFIC tachment is free from defects in material and LEGAL RIGHTS, AND YOU MAY HAVE workmanship and agrees to repair or replace OTHER RIGHTS WHICH VARY FROM under this warranty any defective gasoline STATE TO STATE. product or attachment as follows fr
ページ12に含まれる内容の要旨
warranted part which is not scheduled for re- use of add--on or modified parts. HOW TO FILE placement as required maintenance, or which is ACLAIM: If you have any questions regarding scheduled only for regular inspection to the ef- your warranty rights and responsibilities, you fect of “repair or replace as necessary” shall be should contact your nearest authorized service warranted for 2 years. Any warranted part which center or call ELECTROLUX HOME PROD- is scheduled for replacement as require
