ページ1に含まれる内容の要旨
Owner’s Manual
Model Numbers:
P/N 28334
Date 04-06-05
THT-210/210S/2000/2100/2120
THT-2510/2520/240/2530/2540
HTD-2520PF/2522PF/2526PF
HTD-2530PF,HTS-2530PF
HEDGETRIMMERS
THT-2120
HTD-2530PF
Supplier To The Outdoor Power Equipment Industry
th
ISM, Inc. • 1028 4 Street SW Auburn, WA 98001 Phone: (253) 333-1200 Fax: (253) 333-1212
www.tanaka-usa.com custsvc@tanaka-ism.com
ページ2に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual Before using this unit: • Read the operator’s manual carefully. • Check that the cutting equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment. See “Maintenance”. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth de
ページ3に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual 1. Recoil Starter 2. Fuel Tank 3. Safety Trigger 4. Throttle Trigger 5. Front Handle 6. Rear Handle 7. Spark Plug 8. Hand Guard 9. Cutting Blade 10. Air Cleaner 11. Ignition Switch 12. Blunt Guard (optional) 13. Gear Case 14. Choke Lever 15. Lock Button 16. Blade Cover 17. Lock Button 18. Priming Pump www.tanaka-usa.com
ページ4に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual 2. Warnings and safety instructions. Cutting Safety • Do not cut any material other than plant hedge. Operator Safety • Inspect the area to be cut before each use. Remove objects • Always wear a safety face shield or goggles. which can be thrown or become entangled. • Always wear heavy, long pants, boots and gloves. Do not • Keep others including chi
ページ5に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual 3. Assembly procedures Handle B (3) and Gathering Plate (4) (Fig, 1-1) 1. Remove the four washers and nuts (1) from cutting blade end. NOTE! In case of Handle B installation only, remove only the nut on the longest bolt. 2. Set the gathering plate on the guide bar, then finger tighten the three washers and nuts. *Use one each (5) of the two washers, which have
ページ6に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual 4. Operating procedures Fuel (Fig. 2-1) WARNING! The hedge trimmer is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel • Always use branded 89 octane unleaded gasoline. • Use Tanaka two-cycle oil or a quality two-cycle oil at mixi
ページ7に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual Starting (Fig. 2-2, 2B) CAUTION! Before starting, make sure the cutting attachment does not touch anything. 1. Set ignition switch (1) to the ON position. (Fig. 2-2) *Push priming bulb (4) several times so that fuel flows through the bulb or return pipe. (if so equipped)(Fig. 2-2C) 2. With the safety lever (2) pressed (if so equipped), pull t
ページ8に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual Cutting When cutting, operate engine at full throttle as this maintains proper cutter speed. When trimming top of hedge, hold trimmer so blades are between 15 and 30 degrees from a horizontal position and swing trimmer in an arc toward edge of hedge to sweep cuttings off. When trimming sides of hedge, hold blade vertically and swing unit in an arc. NOTE! (THT-210/2
ページ9に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual 5. Maintenance MAINTENANCE, REPLACEMENT, OR REPAIR OF THE EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY NONROAD ENGINE REPAIR ESTABLISHMENT OR INDIVIDUAL. Carburetor adjustment (Fig. 3-1, 1B) WARNING! The blades may be moving during carburetor adjustments. WARNING! Never start the engine without the complete clutch cover! Otherwise the
ページ10に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual Spark plug (Fig. 3-3) The spark plug condition is influenced by: • An incorrect carburetor setting. • Wrong fuel mixture (too much oil in the gasoline) • A dirty air filter. • Hard running conditions (such as cold weather). These factors cause deposits on the spark plug electrodes, which may result in malfunction and starting difficulties.
ページ11に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual Gear case (Fig. 3-5, 5B) Apply a good quality lithium based grease through the grease fitting until a small amount comes out between the cutter blades and the gear case. NOTE! Lubrication should be applied at 50 hour intervals and more frequent at heavy use. Fuel filter (Fig. 3-6) Remove the fuel filter from the fuel tank and thoroughly
ページ12に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual Maintenance schedule Below you will find some general maintenance instructions. For further information please contact your service dealer. Daily maintenance • Clean the exterior of the unit. • Check the blade guard for damage or cracks. Change the guard in case of impacts or cracks. • Check that the blade is sharp, and without cracks. • Check that the bla
ページ13に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual 6. Specifications www.tanaka-usa.com 12 custsvc@tanaka-ism.com
ページ14に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual 6. Specifications cont. www.tanaka-usa.com 13 custsvc@tanaka-ism.com
ページ15に含まれる内容の要旨
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262 HTD-2520PF/2522PF/2526PF/2530PF,HTS-2530PF Owner’s Manual www.tanaka-usa.com 14 custsvc@tanaka-ism.com
