Shindaiwa T272/EVCの取扱説明書

デバイスShindaiwa T272/EVCの取扱説明書

デバイス: Shindaiwa T272/EVC
カテゴリ: トリマー
メーカー: Shindaiwa
サイズ: 4.11 MB
追加した日付: 10/3/2013
ページ数: 40
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスShindaiwa T272/EVCの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Shindaiwa T272/EVCに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Shindaiwa T272/EVCをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Shindaiwa T272/EVCのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Shindaiwa T272/EVCの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Shindaiwa T272/EVC 取扱説明書 - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Shindaiwa T272/EVCを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Shindaiwa T272/EVCの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

SHINDAIWA OWNER’S/OPERATOR'S MANUAL
T272/EVC TRIMMER
T272X/EVC TRIMMER
T272
T272X
WARNING!
Minimize the risk of injury to yourself
and others! Read this manual and familiarize
yourself with the contents. Always wear eye
and hearing protection when operating this unit.
Part Number 81606 Rev 11/06

ページ2に含まれる内容の要旨

Introduction Attention Statements Throughout this manual are special The Shindaiwa 7-series hand-held Power Read and follow this “attention statements”. Equipment has been designed and built to operators manual. Failure to do so could deliver superior performance and reliabil- result in serious injury. WARNING! ity without compromise to quality, comfort, Wear eye and hearing or durability. A statement preceded by the protection at all times triangular attention symbol and the during th

ページ3に含まれる内容の要旨

General Safety Instructions Work Safely Inspect for broken, missing or improp- WARNING! Trimmers and brushcutters operate at very erly installed parts or attachments. USE Good JUdGmENt high speeds and can do serious damage NEVER extend trimming line beyond ALWAYS wear eye protection to shield or injury if they are misused or abused. against thrown objects. the length specified for your unit. Never allow a person without training or instruction to operate your unit! NEVER operate the engine

ページ4に含まれる内容の要旨

The Properly Equipped Operator Wear hearing protection devices and a broad-brimmed hat or helmet. Wear close-fitting clothing to protect legs and arms. Gloves offer added protection Always wear eye protection such as and are strongly recommended. Do not goggles or safety glasses. wear clothing or jewelry that could get caught in machinery or underbrush. NEVER wear shorts! Always wear a shoulder strap or a harness when operating a unit equipped with a blade. Always operate with both hand

ページ5に含まれる内容の要旨

Product Description t272 Grass t rimmer Using the accompanying illustrations as a Ignition Switch Spark Plug guide, familiarize yourself with your unit and its various components. Understanding Grip Handle your unit helps ensure top performance, long service life, and safer operation. Fuel Tank WARNING! Outer Tube Throttle Trigger Do not make unauthorized modifications or alterations to either Gearcase of these units or their components. t272X Grass t rimmer Cutting Attachment Shield Spa

ページ6に含まれる内容の要旨

Assembly IMPORTANT! Prior to Assembly ■ Engine and shaft assembly The terms “left,” “left-hand,” and “LH”: This unit comes fully assembled with ■ Cutting attachment shield “right,” “right-hand,” and “RH”; “front” the exception of the cutting attachment ■ Cutting attachment and “rear” refer to directions as viewed shield and cutting attachment. ■ Kit containing cutting attachment by the operator during normal operation Before assembling, make sure you have shield bracket and hardware, thi

ページ7に含まれる内容の要旨

Assembly (continued) Cutting Attachment Shield T272/T272X Socket- T272 T272X Head Cap Outer Bolt Screw Cutting Tube Upper Clamp Attachment Shield Bracket Shim Cutting Shim Attachment Nuts Shield Clamp Screw Shim Shim Cutting Attachment Line Cutter Nut Mounting Plate Line Cutter Retaining Nut Figure 8a Figure 8 26013 3. Tighten the four socket-head cap screws 1. Insert the cutting attachment shield to secure the cutting attachment shield. between the outer tube and the cutting Cutting

ページ8に含まれる内容の要旨

Assembly (continued) Mount the Cutting Blade T272X Turn the T7X upside down so the Shaft Bolt Slide the safety clip off-center gearcase output shaft is facing UP and remove the shaft bolt, bolt guard and Bolt Guard holder B from the gearcase shaft. Output Shaft Holder B 1. Align the hole in blade holder A with the matching hole in the gearcase flange and then temporarily lock the Gear Shaft output shaft by inserting a hex wrench Safety Clip Safety Clip through both holes. See Figure 1

ページ9に含まれる内容の要旨

Mixing fuel Examples of 50:1 mixing quantities CAUTION! CAUTION! Gasoline 2-cycle mixing oil This engine is designed to operate on liters milliliters ■ Never use any type of gasoline a 50:1 mixture consisting of unleaded .5 - 1 50 ml containing more than 10% alcohol gasoline and ISO-L-EGD or JASO FC 5 - 1 100 ml by volume! Some types of gaso- class 2-cycle mixing oil only. Use of 10 - 1 00 ml line contain alcohol as an oxygen- 0 - 1 400 ml non-approved mixing oils can lead to ate. Oxygen

ページ10に含まれる内容の要旨

Starting the Engine IMPORTANT! Engine ignition is controlled by a two-position on-off switch mounted on the throttle body. This switch is typically labeled “I” for ON and “O” for OFF. WARNING! T272/T272X Return IGNITION Tube SWITCH Never start the engine from ON the operating position. 1. Slide the ignition switch to the “ON” position. See Figure 16. . Set the throttle lever to the “fast idle”: a. Squeeze the throttle lever toward Primer Bulb the handgrip on the shaft tube. b. Depres

ページ11に含まれる内容の要旨

Stopping the Engine T272/T272X Idle the engine briefly before stopping IGNITION (about  minutes), then slide the ignition SWITCH OFF switch to the “O” (OFF) position. See Figure 0. 27029 Figure 20 Engine Idle Adjustment The engine must return to idle speed 3. If a tachometer is available, the whenever the throttle lever is released. Idle Adjusting engine idle speed should be final Screw -1 Idle speed is adjustable, and must be set adjusted to 3,000 (±50) min (rpm). low enough to permi

ページ12に含まれる内容の要旨

Operation Shoulder Strap T272X IMPORTANT! NOTE: Shoulder Strap Adjust the shoulder strap or harness Although a shoulder strap accessory is recommended for use with grass so the shoulder pad rests comfortably not required for use with a grass trim- trimmers on the off-side shoulder and the cutting mer, a shoulder strap can increase path of the cutting attachment is parallel operator comfort during extended peri- to the ground. Make sure all hooks and ods of operation. adjustment devices are

ページ13に含まれる内容の要旨

T U C T O N O D Operation (continued) Using a Blade T272X ■ Whenever you strike a hard object with Brushcutter Shoulder Strap WARNING! a blade, always stop the brushcut- A shoulder strap provides additional ter and carefully inspect the blade protection against blade thrust. In addi- ■ Before working with a blade- for damage. NEVER OPERATE THE tion, a shoulder strap gives significant equipped unit, always inspect and BRUSHCUTTER WITH A DAMAGED support and comfort to help ensure saf

ページ14に含まれる内容の要旨

Maintenance General Maintenance IMPORTANT! Muffler Blades Keep blades sharp and check blade MAINTENANCE, REPLACEMENT This unit must never be operated with OR REPAIR OF EMISSION CONTROL condition frequently. If a blade’s per- a faulty or missing spark arrester or formance changes suddenly, stop the DEVICES AND SYSTEMS MAY BE PER- muffler. Make sure the muffler is well FORMED BY ANY REPAIR ESTABLISH- engine and check the blade for cracks secured and in good condition. A worn or or other da

ページ15に含まれる内容の要旨

Maintenance (continued) 50 Hour Maintenance Perform more frequently in dusty or dirty conditions. ■ Remove and clean the cylinder cover and clean grass and dirt from the cyl- inder fins. ■ Remove the cutting attachment, cut- New Grease ting attachment holder and gear shaft collar. Remove the filler plug from Old Grease the side of the gearcase and press new grease into the gearcase until old grease is pushed out. Use only lith- ium-base grease such as Shindaiwa Gear Shaft Collar Gearcase

ページ16に含まれる内容の要旨

Long Term Storage Whenever the unit will not be used for 30 To remove the remaining fuel from the ■ Before storing the unit, repair or days or longer, use the following proce- fuel lines and carburetor and with the replace any worn or damaged parts. dures to prepare it for storage: fuel drained from the fuel tank. ■ Remove the air cleaner element from ■ Clean external parts thoroughly. 1. Prime the primer bulb until no more the carburetor and clean it thoroughly fuel is passing through. w

ページ17に含まれる内容の要旨

Troubleshooting Guide ENGINE DOES NOT START What To Check Possible Cause Remedy Faulty recoil starter. Consult with an authorized servicing dealer. NO Fluid in the crankcase. Does the engine crank? Internal damage. YES Loose spark plug. Tighten and re-test. NO Good compression? Excess wear on cylinder, piston, Consult with an authorized servicing dealer. rings. YES Fuel incorrect, stale, or contaminated; Refill with fresh, clean unleaded gasoline NO mixture incorrect. with a pump octane of 87

ページ18に含まれる内容の要旨

Troubleshooting Guide (continued) LOW POWER What To Check Possible Cause Remedy Operator is overworking the unit. Cut at slower rate. Carburetor mixture is too lean. Consult with an authorized servicing Is the engine overheating? dealer. Improper fuel ratio. Refill with clean fresh unleaded gasoline with a pump octane of 87 or higher, mixed with Premium -cycle mixing oil at a 50:1 gasoline/oil ratio. Fan, fan cover, cylinder fins dirty or Clean, repair or replace as necessary. damaged Carbo

ページ19に含まれる内容の要旨

Troubleshooting Guide (continued) ADDITIONAL PROBLEMS What To Check Possible Cause Remedy Clean or replace the air filter. Clogged air filter. Replace the fuel filter. Clogged fuel filter. Poor acceleration. Consult with an authorized servicing Lean fuel/air mixture. dealer. -1 Idle speed set too low. Adjust:3,000 (±300) min . Switch turned off. Reset the switch and re-start. Fuel tank empty. Refuel. See Fuel section of manual. Clogged fuel filter. Replace fuel filter. Engine stops abrup

ページ20に含まれる内容の要旨

Emission System Warranty Statement Your Warranty Rights and Obligations Owners Warranty Responsibilities The California Air Resources Board, the U.S. Environmen- As the small off-road engine owner, you are responsible for tal Protection Agency and Shindaiwa Corporation are pleased the performance of the required maintenance listed in this to explain the exhaust and evaporative emission control sys- owners manual. Shindaiwa Corporation recommends that tem warranty on your new small off-road (


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Shindaiwa 63848-94010 取扱説明書 トリマー 14
2 Shindaiwa 80844 取扱説明書 トリマー 8
3 Shindaiwa 80974 取扱説明書 トリマー 3
4 Shindaiwa 68800-94313 取扱説明書 トリマー 2
5 Shindaiwa 80775 取扱説明書 トリマー 0
6 Shindaiwa 81601 取扱説明書 トリマー 1
7 Shindaiwa 81606 取扱説明書 トリマー 0
8 Shindaiwa 81372 取扱説明書 トリマー 0
9 Shindaiwa 81010 取扱説明書 トリマー 0
10 Shindaiwa 81605 取扱説明書 トリマー 0
11 Shindaiwa 81646 取扱説明書 トリマー 0
12 Shindaiwa 81643 取扱説明書 トリマー 0
13 Shindaiwa 81642 取扱説明書 トリマー 0
14 Shindaiwa 82014 取扱説明書 トリマー 0
15 Shindaiwa 89309 取扱説明書 トリマー 0
16 Sony PCS-G70P 取扱説明書 トリマー 12
17 Sony PCS-G70 取扱説明書 トリマー 12
18 ABC Office 440 取扱説明書 トリマー 2
19 Sony 370A 取扱説明書 トリマー 83
20 ABC Office 448 取扱説明書 トリマー 2